At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
lift car put two stands first.find drain bolt,drain oil then put back bolt do not over tight.move to oil filter remove with GASKET!!!put new one DO NOT OVER TIGHT.fill the oil and check level.done.
No. The oil is very easy to change. All you need is a filter wrench and a 15 mm. socket, and a drain pan. Get under the truck and the oil filter is right there and the drain plug is in the oil pan. Drain the oil first, then remove the oil filter with the filter wrench. Take your finger and dip it in the oil and put a film of oil on the new oil filter gasket. Then install the new oil filter. Once you install the new oil filter, put the drain plug back in. Then put 5 quarts of new oil in the oil fill.
oil filter located inside of front drivers side fender. lay down and look up you will see the filter in the front of the fender. oil drain plug located on the back of the black oil pan I think its a 15mm bolt unbolt let drain. When done draining put it back in the oil pan. next pull oil filter off turn counter clockwise and put new filter back on then fill with 6quarts of oil. I think its 5w-30 but you can use 10w-30 won't hurt it.
take the drain plug off of the engine oil pan, let the oil drain. replace the oil filter. put the drain plug back on. refill with proper oil, usually around four-ish quarts.
Take and drain all the oil out and if you have started it change the filter if you havent started it since adding antifreeze to the oil after draining all the oil out put the oil plug back in and fill with oil if you started it do change the oil filter and drain drain all the oil out and refill.
Jack up pass side.Put cardboard, BIG piece under engine just in case. Using a pan to drain the oil in put under oil pan drain plug. Remove drain plug with socket wrench. Let drain 5 min. Check the gasket on the drain plug, if bad replace with new gasket .99 cents to replace gasket only on plug. Put plug back in DO NOT OVER TIGHTEN the plug. Slide drain pan with drained oil to the front to remove oil filter. Using a filter wrench remove oil filter. Let drain. When installing new filter put a little new engine oil on the rubber gasket on the filter with your finger. Screw filter back on tighten with filter wrench. Fill van with oil from front valve cover opening.
Remove drain plug from oil pan to drain oil. Remove oil filter using filer wrench. Instatt new oil filter. Put oil drain plug back in. Check owner's manual for oil capacity, put all oil in minus one quart. Start engine let run for aproximately 10 seconds. put in rest of oil and check dip stick to ensure corret amont.
go to a parts store and they will give you all the right supplies and tell you how to do it. There is a drain plug on the bottom of your oil pan take plug out and let oil drain. Take out oil filter by hand or with a oil filter wrench. Take new filter and fill it with as much oil as you can without spilling it all over putting filter back in, apply a thin coat of fresh oil to the rubber ring on the oil filter and screw it back on the engine hand tight (do not tighten using a wrench). Put drain plug back in. Fill engine back up with oil. Replace oil cap> Done.
yourgoing to have to drain it from the pan just pull the drain plug and let it all drain. change the filter and then replace with 5 quarts of 10w30 oil perferably quakerstate or valvoline brand
If you have never changed your oil before use care:
0.) Safely Jack up vechile
1.) remove oil filler cap
2.) remove oil drain plug on oil pan
3.) Let oil drain into a container
4.) Flush a quart of through with the drain plug removed to get any deposits out.
5.) remove and drain oil filter
6.) install new oil filter(make sure you put some oil on the filters gasket by hand)
7.)Install oil drain plug
8.) Re-fill with oil
9.) Put oil filler cap back on
Hope this helps and again use with care if you have never turned a wrench before, people get hurt easily by being careless while working under a car.
×