What should I do next after cancelled radio code using VIN no on Toyota Ascent 07? Its displayed 3 lines --- on radio stereo?

The antitheft system only allows you 15 seconds to complete each step. Have a pen and paper to get all codes before you begin.

Step 1: Start the vehicle and turn on the radio.

Step 2: Press and hold preset numbers 2 and 3 until a three digit code appears on the radio display. Write this code down.

Step 3: Press the AM/FM button. Your radio will display a second three digit code. Write the second code down. You will now have a six digit code.

Step 4: Call the Chevy Radio Code phone line at 1-800-537-5140. Enter 106010 followed by the # key to direct you to the radio code retrieval system.

Step 5: Enter the six digit code you retrieved in steps 2 and 3 followed by the * key. They must be in order. You will be given a four digit radio code. Write down the radio code.

Step 6: Start your vehicle and turn on the radio. Using the Minute and Hour buttons, enter in the four digit radio code to your stereo system. Press the AM/FM button to unlock your stereo.
Good luck

Try going to this website, it does charge for the code. www.radio-code.com

toyota ascent are fitted with different radios during the model production run

the glove box owner manual should have a card with a 3 or 4 digit number you enter into the radio
.if missing contact or take the ascent to a toyota service center and you get the correct code using the vin number

Try this: How to Unlock a Chevy Radio Step 1: Start the vehicle and turn on the radio.
Step 2: Press and hold preset numbers 2 and 3 until a three digit code appears on the radio display. Write this code down.
Step 3: Press the AM/FM button. Your radio will display a second three digit code. Write the second code down. You will now have a six digit code.
Step 4: Call the Chevy Radio Code phone line at 1-800-537-5140.
Step 4: Enter 106010 followed by the # key to direct you to the radio code retrieval system.
Step 5: Enter the six digit code you retrieved in steps 2 and 3 followed by the * key. They must be in order. You will be given a four digit radio code. Write down the radio code.
Step 6: Start your vehicle and turn on the radio. Using the Minute and Hour buttons, enter in the four digit radio code to your stereo system. Press the AM/FM button to unlock your stereo.
How to Unlock a GM Radio Step 1: Start the vehicle and turn on the radio. The radio will display "LOC" indicating the Theftlock system is activated.
Step 2: Press and hold preset buttons 1 and 4 for ten seconds. (If you don't have a fourth preset button, press and hold presets 2 and 3.) The radio will display a three digit number. Write this number down.
Step 3: Press the AM/FM button. Your radio will display a second three digit code. Write the second code down. You will now have a six digit code.
Step 4: Contact your local GM Dealer and give them the six digit code. They will give you a four digit radio code.
Many dealers will give you your radio code for free, while others may charge a small fee. If your dealer is charging a larger fee, consider calling another dealer or doing a Google search for sites offering GMC Radio codes. They usually charge a small (around $10) fee.
Step 5: Start your vehicle and turn on the radio. Press the Hour button on the radio until the first two number of the code appear. Next, press the Minute button until the last two numbers of the code are displayed. Once all four digits appear, press the AM/FM button to unlock your stereo. The display will read "SEC" indicating you have successfully unlocked your radio and it is fully operational.
If radio display reads "INOP" while the vehicle is on, too many incorrect radio codes have been entered. To remove "INOP" from your display and unlock your radio, you must leave the key in the On position for one hour. Once you've retrieved your radio unlock code, write it down for future use. Your radio code will not change and having it handy will save from going from the radio code retrieval process again.

3 DIGITS ??? USALLY ITS 4 DIGITS ON STEREOS, CHECK WHIT YOUR NEAREST DEALER FOR THE CODE TOO YOUR CAR

Send the request via email through this site these guys can help or go back to dealer and get them to get it for you.
http://autoforum.classifieds1000.com/Volkswagen-Quantum/2007_VW_golf_radio_code
Below is procedure once you have the code:

* Turn on radio -- the word "SAFE" will be displayed.

* First press the MODE button and then press the SCAN button and hold them down simultaneously until "1000" appears in the frequency display. Release the buttons. Do not, under any circumstance, continue holding the buttons down or press them once again. This would cause the radio to take the number "1000" as the code number.

* Using the first four radio station buttons, enter the code number found on your Radio Card. Use button 1 to set the first digit of the four digit code, button 2 to set the second digit, etc. The first digit of a four digit code must be "1". If your code number has three digits, the first digit on display must be set blank.

* Once the code is shown on the display, press and hold the MODE button and SCAN button simultaneously until the word "SAFE" appears in the frequency display. Release the buttons. A radio station frequency will automatically be displayed. The radio will now play once again.

If, when cancelling the electronic lock-up, a wrong code number is entered by mistake, the word "SAFE" will appear in the frequency display first blinking, and then continuous.

You can now repeat the entire cancelling procedure but only once. The number of attempts will be shown in display.

If the wrong code number should be entered again, your radio will be locked up for approximately one hour. The radio will not play. Leave the radio switched on. After an hour, you can cancel the electronic lock-up as previously described.

This cycle, two attemps - one hour lock-up continues again. //

only the dealer can get that information

Oribeeboy is spot on for a 100 series Landcruiser - last 3 VIN numbers.
Let's say the last 3 VIN Nos were 264
Turn the ignition key so that the radio displays "SEC"
then: press "TUNE"and press No1 button on the radio at same time
then: press No1 button 2 times
then: press No2 button 6 times
then press No3 button 4 times
Finally hold the "SCAN" button to confirm the code. The radio will then turn itself off. You can then turn it on in the normal way.
(Hopefully!)

The unlock code for the 11712 audio unit is as follows:

6 4 0 7 0 2

A FixYa rating for my assistance would be greatly appreciated.

The only way to unlock the radio is by using a scan tool. The scan tool sends the appropriate diagnostic message (relearn VIN) to reset the radio. Using a scan tool, select the radio VIN relearn procedure from the module replacement screen in Vehicle Control Systems