1999 Isuzu Trooper Logo
Y
Yuri Kokhanov Posted on May 24, 2016
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

How to replace inner rear axel seal

Gear oil leaking out to brake shoes. Outer is duster and seal inner by differential. do i need remove differential to replace inner seal?

Answer This Question
  • _-__-___-_
    _-__-___-_ May 26, 2016

    Hi Yuri Kokhanov, I want to help you with your question,
    why not post a photo of your axle first.
    so we can see if it has the carrier, per OEM shows., Ive not done all 3 bodies
    2wd
    4wd
    TOD. (runs special sensors, and diff axle)
    sorry, what you have is , well, what's there.

×

1 Answer

_-__-___-_

_-__-___-_

Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

  • Isuzu Master 20,706 Answers
  • Posted on May 26, 2016
_-__-___-_
Isuzu Master
Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

Joined: Apr 06, 2013
Answers
20706
Questions
2
Helped
6797015
Points
57965

Why not login to mitchells and read all that.
why ask for help, and get wrong answers, or incomplete.
the FSM book covers this job.
per axle type.
is car 2wd or 4wd, is it with TOD?
why do I ask this will the axle are not the same.. see>.
sad no photo of axle posted, and all this goes byebye what's there.?
some axles have inner clips. the Rodeo does.

here is what , one book shows. i think it is wrong, for full coverage

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Rear wheel
    • Disc brake caliper and bracket
    • Disc brake rotor
    • Wheel speed sensor bracket
    • Parking brake cable and bracket
    • Parking brake shoes
    • Axle shaft
    • Snapring and discard it
    • Bearing, press it off the axle shaft with the bearing holder and oil seal


the oem page shows no such clip....
there are 2 seals the inner and outer.
#3 is inner. #4 is the bearing, the keeper is to right of #4.
the last photo here is buying bearing, see that keep K?
if you see that , that means no clips.
how to replace inner rear axel seal - 26203934-qvvdcm34jvcwbumk4o5kywm4-3-0.jpg



how to replace inner rear axel seal - 26203934-qvvdcm34jvcwbumk4o5kywm4-3-3.jpgcm34jvcwbumk4o5kywm4-3-3.jpg" alt="26203934-qvvdcm34jvcwbumk4o5kywm4-3-3.jpg" class="h_mi" />

Testimonial: "Thank you... everything I looked showed wrong diagrams and differentials w/snap ring. And Trooper do not have it, it was much easy to do"

  • 1 more comment 
  • _-__-___-_
    _-__-___-_ May 26, 2016

    k above = keeper. (sleeve holder)under huge force (pressed) on, this device keep the axle wheel/tire from flying off car in wild turns.... see?
    and the lack of a rear cover tell you that.
    the axles both must be pulled to remove the CARRIER pig.

    id just have.
    drained axle ,and the housing end bolts off.
    then with my slide hammer on the studs
    it be off easy if not it has clips.
    take no time to do this.
    the with axle out. take it to shop and get them to press a new one on, just did one last month.
    and then put the inner seal
    use the same magic tool the slide hammer
    with the correct end, to pull old seal out.
    then use some pcv pipe or the like , matched up to press in the new seal not distorting it.
    like that.

  • _-__-___-_
    _-__-___-_ Jun 02, 2016

    yes the rodeo and trooper run diff, axles
    best is to read the FSM book that matches your car,
    mitchill diy has this.... not spam, just what most real shops use, (not DIY , real)

  • Anonymous Jun 06, 2016

    why not long in and read first then ask question there, not clear.... RTM its called
    http://www.eautorepair.net/Marketing/Def...

    read the manual please.

×

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Why do I have oil in my breaks of my 1996 Chevy
if your talking about the rear brakes its probably the differential axle seal that is leaking differential oil out of the rear end onto the brake shoes. you will have to pull the rear axle to replace the seal and clean the rear brakes/area with brake cleaner or replace the rear brakes if they are too soaked with brake fluid.
Read full answer
Oct 04, 2014 • Cars & Trucks
0helpful
1answer

Leak from rear axel
The differential axle seal will need to be replaced to repair the leak.
Read full answer
Feb 07, 2013 • 2003 Ford Escape
1helpful
1answer

Left rear axle leaking - Dealer states $820 to fix due to many parts within the axle. Does this sound right?
fix same problem myself...these's' only 1 inner seal (differential output seal only-about 10$ each) that needs to be replace and new brake shoes (20$ part)..assumed u have rear drums and it leaked diff fluid on the brake shoes..but, i also replaced the brake cylinder (15$ part)-u have to disconnect brake cylinder to remove axle..look on internet for procedures..http://www.yotatech.com/f128/replacing-rear-axle-seals-3rd-gen-4runner-76339/..hope this helps..all dealers are ripoffs-worked at toyota for a year
Read full answer
Jul 31, 2010 • 1999 Toyota 4Runner
0helpful
3answers

Rear brake drum leaking on my 1989 ford bronco 2 y did it happen and how do u fix it
The drum isn't leaking, either the wheel cylinder is leaking or the line is leaking
Read full answer
Oct 07, 2009 • 1989 Ford Bronco II
1helpful
1answer

Grease and differential oil inside left rear drum
Not that difficult, raise and support the rear of the truck and remove the wheels. Might as well replace both sides so you know you have new seals, remove the differential cover and drain the fluid. Once differential is opened and cleaned , remove the axle "C" clip that hold the axle in place and slide the axle out. Once the axle is out remove the wheel seal and clean around the area. This would be a good time to replace the wheel bearing too since you have access to them and there not that expensive. Install the new bearing and seal, note make sure you oiled the bearing and seal before installing it back and take care when installing the axle back in and "C: clip. Use RTV silicon gasket maker to seal the differential cover and wheels back on and lower. If your lazy like i am, you can drain the differential fluid and replace it with a 50/50 mix with gear oil and Lucas engine oil additives. That may stop the leak and get you a few more miles. You gear oil is (ford 75W-140) (Dana 80W-90)and the capacity is 2.6 liters and 3.5 liters if you have the 10.25 Ring gear. Good luck and hope this helps.
Read full answer
Jul 07, 2009 • 1998 Ford F150 Regular Cab
4helpful
1answer

Rear Axel Seal Leaking, How do I pull the axel to repair?
You will need to remove the differential rear cover,drain fluid, remove wheel, brake drum, (rotor) . Unbolt center diff. pin, carefully remove (don't loose shims) push axle in remove lock keeper, then slide out axle, replace seal, put some grease on it, slide axle in reverse all to install.
Read full answer
May 22, 2009 • 1999 Jeep Grand Cherokee
4helpful
1answer

How do you remove right rear axle on a 2004 ford crown vic to replace seal on wheel?
Section 05-02A: Axle, Integral Carrier — 8.8-Inch Ring Gear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual REMOVAL AND INSTALLATION Axle Shaft NOTE: Whenever replacing the rear axle lubricant, use Rear Axle Lubricant XY-90-QL (ESP-M2C154-A) or equivalent.
Removal
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The rear brake anti-lock sensor must be removed before the axle shafts are removed. The rear brake anti-lock sensor is bolted on the rear disc brake caliper anchor plate.
  1. Raise vehicle to desired working height. Refer to Section 00-02 . Remove rear wheel (1007) and tire assembly. Remove rear disc brake calipers (2552) and rear disc brake rotors (2C026) .




  1. Clean all dirt from area of axle housing cover with a wire brush and/or cloth.
  1. Drain rear axle lubricant by removing the axle housing cover .
  1. Remove differential pinion shaft lock pin and differential pinion shaft .


    9979cb3.gif
  1. Push flanged end of the axle shafts toward the center of the vehicle and remove the rear axle shaft retaining u-washer from the button end of the axle shaft .



  1. Remove axle shaft from the rear axle housing , being careful not to damage the inner wheel bearing oil seal (1177) and rear brake anti-lock sensor ring.
Installation
NOTE: Check for presence of rear axle shaft o-ring (4A332) on the spline end of the shaft and install if not present.
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Care must be taken not to let axle shaft splines damage oil seal or bearing assembly.
  1. Carefully slide axle shaft into rear axle housing without damaging rear wheel bearing (1225) or rear brake anti-lock sensor indicator (2C189) . Start splines into side gear and push firmly until the button end of axle shaft can be seen in the differential case .
  1. Install the rear axle shaft retaining u-washer on the button end of the axle shaft splines, then pull the shaft outboard until the shaft splines engage and the rear axle shaft retaining u-washer seats in the counterbore of the differential side gear .
  1. Position the differential pinion shaft through the differential case and differential pinion gears , aligning the hole in the differential pinion shaft with the lock bolt hole. Apply Rear Axle Lubricant to differential pinion shaft lock pin . Install differential pinion shaft lock pin and tighten to 20-41 Nm (15-30 lb-ft). sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Differential pinion shaft lock pin must be tightened to specification using Stud and Bearing Mount E0AZ-19554-BA (WSK-M2G349-A1) or equivalent.




    NOTE: Axle housing cover must be installed within 15 minutes of application of the silicone rubber or new silicone rubber must be applied.
    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure machined surfaces on both axle housing cover and rear axle housing are clean before installing the new silicone sealant. Inside of axle must be covered when cleaning the machined surface to prevent axle contamination. Tighten the cover bolts in a crosswise pattern to ensure uniform draw on axle housing cover .
  1. Apply Silicone Rubber D6AZ-19562-AA or BA (ESB-M4G92-A or ESE-M4G195-A) or equivalent. Install axle housing cover and tighten retaining bolts to 28-38 Nm (38-52 lb-ft).



  1. Add Motorcraft Rear Axle Lubricant XY-90-QL or KL (ESP-M2C154-A) or equivalent until it is 6-14mm (1/4-9/16 inch) below bottom of fill hole. Add 118.3 mL (4 oz) of Ford Additive Friction Modifier C8AZ-19B546-A (EST-M2C118-A) or equivalent to Traction-Lok axles. Install fill plug and tighten to 20-41 Nm (15-30 lb-ft).
  1. Install rear brake anti-lock sensor indicator . Tighten retaining bolt to 4.5-6.8 Nm (40-60 lb-in).
  1. Install rear disc brake caliper and rear disc brake rotor .
  1. Install wheels and tires.
---------------------------------------------------------
  1. Insert Rear Bearing Remover T85L-1225-AH in bore and position it behind bearing so tangs on tool engage bearing outer race. Remove rear wheel bearing and inner wheel bearing oil seal as a unit, using Impact Slide Hammer T50T-100-A.

    Rear Disc Brake Caliper Anchor Plate




  1. Lubricate the rear wheel bearing with Rear Axle Lubricant.



  1. Install rear wheel bearing into the housing bore using Axle Tube Bearing Replacer T78P-1225-A.



    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Installation of rear wheel bearing or inner wheel bearing oil seal assembly without proper tool may result in an early bearing or seal failure. If inner wheel bearing oil seal becomes cocked in bore during installation, remove it and install a new one.
  1. Install the inner wheel bearing oil seal using Axle Tube Seal Replacer T78P-1177-A. Use Premium Long-Life Grease XG-1-C or K (ESA-M1C75-B) or equivalent between the lips of the inner wheel bearing oil seal .



  1. Install axle shafts as outlined.
Read full answer
May 13, 2009 • 2004 Ford Crown Victoria
2helpful
1answer

Rear Axel Seal
Wheel, brakes etc that are in way of pulling axle out have to come off. Drain rear end fluid, remove rear housing cover, remove bolt that holds pin in differential, remove differential pin, push in slightly on axle to remove "U" clip that holds shaft in, then slide shaft out. replace seal. Reverse procedure for re-install & fill with gear lube. If any questions, get back to us.
Read full answer
Apr 16, 2009 • 2002 Ford Mustang
3helpful
1answer

Replace left rear axle seal 1999 ford explorer
Axle Shaft Removal
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the differential housing cover (4033).
    1. Loosen the bolts and drain the lubricant from the rear axle housing (4010).
    1. Remove the bolts.
    1. Remove the differential housing cover.
Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Turning the differential case (4204) or an axle shaft (4234) with the differential pinion shaft (4211) removed will cause the differential pinion gears (4215) to fall out of the assembly and damage the components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  2. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the U-washer groove.
  3. Remove the U-washer (4N237).
  4. Push the axle shaft inboard.
  5. Remove the U-washer.
Reinstall the differential pinion shaft.
  1. Install the differential pinion shaft.
  2. Install the differential pinion shaft lock bolt finger-tight.
  3. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal (1177).
    Remove the axle shaft.
-----------------------------------------------------------------------------------------------------------------
Seal Removal
  1. Remove the axle shaft (4334). For additional information, refer to Axle Shaft in this section.
  1. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never remove the wheel bearing oil seal (1177) by itself. Always remove the rear wheel bearing (1225) and the inner wheel bearing oil seal at the same time.
    NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged with foreign material.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal together.
6c7eb46.gif Installation
  1. Lubricate the new rear wheel bearing.
    • For 4.0L SOHC and 4.0L EI with limited slip rear axles and 5.0L vehicles, use SAE 75W-140 High Performance Rear Axle Lubricant F1TZ-19580-B or equivalent meeting Ford specification WSL-M2C192-A.
    • For 4.0L SOHC and 4.0L EI with conventional rear axles, use SAE 80W-90 Premium Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.
  1. Using the special tools, install the rear wheel bearing.

ece7d89.gif
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the wheel bearing oil seal.
c21e27d.gif
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.
Read full answer
Feb 22, 2009 • 1999 Isuzu Rodeo
7helpful
1answer

Leaking left rear wheel seal.
Loosen differential cover and let oil drain. Remove cover, remove E clip lock from axel. Pull axel out. Remove bearing seal. Install new seal and reinstall axel. Reinstall E clip lock and new cover gasket. Fill with 75-90wt gear oil. Now I know that sound pretty straight forward. But there are some things to remember. The E clip lock can be difficult to remove sometimes. The most important thing is the seal, you will need to make sure it gets seated correctly and not torn when installing axel
Read full answer
Jul 26, 2008 • Chevrolet Silverado 1500 Cars & Trucks
Not finding what you are looking for?

View Most Popular

1999 Trooper

  • Cars & Trucks

Related Question

Why do I have oil in my breaks of my 1996 Chevy

  • Cars & Trucks

Related Topics

477 views

Ask a Question

Usually answered in minutes!

Popular Questions

Isuzu 320 KB v6 camshaft timing diagram posted to wrong forum.

1999 Isuzu Trooper

Isuzu bighorn diesel 4jg2 engine timing diagram

1994 Isuzu Trooper

Isuzu Trooper (Bighorn) 4JX1 Engine Common rail

1998 Isuzu Trooper

2002 ISUZU TROOPER, TOD CHECK LIGHT IS FLASHING,

2002 Isuzu Trooper

My ABS light on my Isuzu trooper remain on how can I reset

2002 Isuzu Trooper

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Isuzu Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...