After driving when u put in reverse it stalls when u restart the engine it is fine

engine dies when shifting into reverse or drive - Third Generation ...

www.thirdgen.org/forums/tbi/346079-engine-dies-when-shifting.html

Feb 11, 2006 - engine dies when shifting into reverse or drive ... After it dies it starts right up and idles fine in park or neutral. ... these ignition items because you weretrying to cure the stalling, or, did the stalling occur after you replaced these items? ...The only thing that kept the car running was adjusting the Idle screw up.

Engine Dies When Placed In Gear***Split from Spittybug...EFI ...

dmctalk.org > ... > MAIN FORUMS > Custom DeLoreans/Mods > EFI

Jul 5, 2012 - 18 posts - ‎4 authors
Just to give an update on my car - I've been having an issue with the car stalling when moving from Park into Reverse or Drive (I have automatic). ... I have been playing with the idle advance trying to get more ... I put in the remainder of the AT fluid I had on hand and the car never died on shifting after that.

starts but dies when shifted into drive or reverse - Suzuki Forum

engine starts with no problem; but, when I put in gear and ...

www.cargurus.com > Questions > Hyundai > Sonata

CarGurusNov 15, 2012 - The engine just fall dead when you step on the gas; it seems to jerk before ... My car does the same thing but i put it in neutral n it starts up. ... I have a 2004 kia optima it jerks when I go into reverse it was driving ... start and run fine butwhen I put it in drive or any other gear it dies! ... 2002 Hyundai Elantra GT.

Engine stalls when tranny put in Drive or Reverse - Kia Forum

www.kia-forums.com/kia-carnival...2002.../43407-engine-stalls-when-tr...

Feb 28, 2008 - 10 posts - ‎3 authors
Give it a little gas before putting in D or R and it will go. .... When I start the van cold and shift the tranny into drive or reverse.....the whole front ... won't run in forward gears - Kia Forum
10 posts
May 25, 2012
Intriguing problem - engine rough idle & hesitation ...
10 posts
Aug 31, 2011
2006 Kia Spectra engine stalls and bad idle, cleaning the ...
10 posts
Aug 30, 2010
2002 Kia Spectra Won't Go Out of Park - Kia Forum
3 posts
Oct 28, 2008
More results from www.kia-forums.com

I need a little more info. I presume it is automatic, not a manual trans. Was it multiple times that it stalled when you shifted to reverse? or just 1 time. Is the check engine light on, and/or the D4 light flashing?

sounds like your alt. is starting to go out and possibly a dead cell in the battery check to see if battery and alt. are working

check for pinch wires around core install. also a vacume leak from same job not plugged

This problem is commonly caused by a dirty automatic idle speed control valve and throttle valve but always run a OBD2 fault code as well as the cleaning procedure. Buy a can of throttle valve cleaner (do not use carburetor spray cleaner!) from NAPA or Carquest (made by CRC chemicals) and spray it into the air intake while the engine is running, use up about 1/2 the can, engine will try to stall hold the speed up, shut it down and let it soak for 30 minutes, restart and blow out the remaining fluid, shut it down and disconnect the negative battery cable for 5 Min's to reset the base idle control. If the above cleaning doesn't cure your issues you need to have the computer controlled automatic idle speed control system diagnosed and repaired by a dealer or electronic engine control repair shop.

Not saying this is your problem but I had a ram 1500 5.9l gas do the same thing would start and die as soon as I put it in drive but would run fine in reverse after doing all kinds of trans testing it ended up being the crank sensor still doesn't make sense to me but it would back fire and carry on in drive changed sensor and runs great and better fuel mileage

Since the car stall only in the drive position, it sounds(i'm not there to actually ck the car)like when the engine torques, it might be pulling on a harness somewhere and killing the ignition. Do this,start the car and under the hood while the engine is running, move or jiggle the harnesses around and see if the car stalls. If the car stalls try to pinpoint the location on the harness and look for frayed or broken wires.

try the map sensor. it is cheap and takes about 20 minutes to change. Good place to start.