Ihave a 1998 Buick Century, removed drivers seat to convert to RHD for mail carrier,now seat belt chimes all the time, need to be able to unhook chime?

Audible Warnings Description
The seatbelt/ ignition key/ lamps alarm provides an audible warning for the following signals:
• The fasten seat belt reminder
• The key in the ignition reminder
• The headlamps ON reminder

Seat Belt/ Ignition Key/ Lamps (Warning) Alarm
Behind the instrument panel, on the right side of the A/C module

Looks like it has several connectors to it, just pull the one connector to stop the chime (warning) your hearing. Assume you have one on all the time? annoying isn't it .

You will need to unbolt them from the floor, the nuts are under the car.

Try under dash, Drivers side, Left side near side of car at firewall

unhook the batt. or remove the fuse hold the back of the socket and unscrew the inner part with external pliers or eqiv.

COULD BE YOUR HEATER CONTROL UNHOOK IT THEN HOOK IT BACK UP AND SEE IF THAT WORKS

sir , you are talking about seat belt chimes?

METHOD 1 - NO TOOLS REQUIRED

1. Sit in the vehicle driver's seat.
2. Remove the ignition key from the ignition lock cylinder.
3. Close all of the vehicle's doors.
4. Press and HOLD the door "LOCK" switch to the "Unlock" position.
5. Insert and remove the ignition key twice (without rotating the ignition lock cylinder).
6. Insert the ignition key a third time leaving the key in the ignition lock cylinder. The ignition must be in the "OFF" position.
7. Release the door "LOCK" switch from the "Unlock" position (three fast chimes will be heard when the remote control door lock receiver enters the programming/diagnostic mode).
8. Press and HOLD the transmitter "LOCK" and "UNLOCK" buttons simultaneously for at least 12 seconds . Two fast chimes will be heard confirming successful programming.
9. Repeat step 8 for each additional transmitter to be programmed.
10. Remove the ignition key from the ignition lock cylinder

The transmitter may have lost programming,
In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.

IMPORTANT:

• Once entering this procedure, programming the first transmitter erases all previous transmitters. You must program all transmitters.
• Program one vehicle at a time. One transmitter could be programmed into other vehicles that are also on program mode in close proximity.

1. Sit in the driver's seat.
2. Remove the ignition key from the ignition lock cylinder.
3. Close all vehicle doors.
4. Press and hold unlock on the door lock switch.
5. While holding the door lock switch in the unlock position, insert and remove the ignition key twice. Do not rotate the ignition lock cylinder.
6. Insert the ignition key a third time leaving the key in the ignition lock cylinder. The ignition must remain in the LOCK position for the rest of the procedure.
7. Release the door lock switch. You will hear three chimes. This chime feedback indicates that transmitter programming is active.
8. Press and hold the lock and unlock buttons at the same time on the keyless entry transmitter for 12 seconds . You will hear two chimes. This chime feedback indicates that the transmitter has been programmed successfully.
9. Repeat step 8 for the rest of the transmitters (for a total of 4 transmitters).
10. Exit this procedure by removing the ignition key from the ignition lock cylinder.

It should have bolts holding down the back of the seat. If you can get to these, remove them. Most CAR seats do not have bolts in the front - only tabs that slide into slots in the floorboard. Once the rear bolts are out, you should be able to slide the seat loose and remove it. There will be a wire plugged in underneath or on the seat belt assembly that you will have to unplug before removing the seat.

try parking on a level surface, then gently feed the belt back where it comes from, very gently pull it back out as if you were putting it on. hope this helps