Where is headlight flash relay located?

are you DIY, doing or did this work or others?
your hands? if did, see the HID bulb below?
head light , right side, dead (USA right side) ?
in UK passenger is LEFT side. so please say left /right

• low beam
• high beam
• and high beam flaster switch

OR all 3 dead. selections dead.
and all other electric things work and car drives ok.
yes the 2 orange are parking lamps. all sides/corners and ends of car good parking lamps.

off hand using the wrong bulbs not reading the free users guide in the glove box for bulb number
USA answers only (me)
Chrysler maker
this car uses the BCM body brain to run front lamps
and does so using 4 outputs. 2 low and 2 high each side.

some of these cars have HID lamp options.
and are totally unique, for head lamps! IF TRUE.

standard bulbs are H3 TYPE. AND ARE NOT HID.
PAGE 406 IN THE USER GUIDE
HID BULBS ARE HIGH VOLTAGE LAMPS.
DO NOT PLAY WITH THOSE, OR GET SHOCKED
AND REQUIRE SPECIAL PARTS TO REPAIR IT.
Same page
On vehicles equipped with High Intensity Dis-
charge Headlights (HID), when the headlights are turned
on there is a blue hue to the lights. This diminishes and
becomes more white after approximately 10 seconds, as
the system charges.

the lost free manual is here by maker

https://vehicleinfo.mopar.com/assets/publications/en-us/Chrysler/2007/Pacifica/1577.pdf

and more
Do not touch the glass of High Intensity Discharge (HID) or halogen bulbs with fingers or other possibly oily surface. Reduced lamp life will result.

HID install 1 step says
Place the igniter on the HID lamp. Do not at this time connect the igniter electrical connector. It will make it unable to twist the igniter to the closed position.

the igniter can be bad.
HID uses D2S bulbs only .
Chrylser p/n
MOPAR 4865941AB
and looks like this.

VERY EXPENSIVE TOO. PARTS.


PARTS PAGE

https://www.rockauto.com/en/catalog/chrysler,2007,pacifica,4.0l+v6,1433518,electrical-bulb+&+socket,headlamp+bulb,11701

Hello Joe

Not sure what you mean when you say "when I turn the lever loose"?

It sounds like the switch is faulty. If both headlights come on and then go off when you touch the lever, you know it isn't the bulbs, relays or fuses because they start off working.

@Larry Ng is the Fixya Expert on Jeeps. Hopefully he will come by tomorrow.

PAWEL IS A BOT. HE POSTS GENERIC ANSWERS. AND OVERLAYS NAME OF YOUR CAR. 82 GENRIC ANSWERS HIM
AND LIES ABOUT IGN SWITCH.
NOW YOUR CAR.! FACTS, ONLY, 1 CAR
LEARN TO USE THE DMM , CORRECTLY;
HEAD LAMPS ON.(SWITCH) NO KEY IS NEEDED FOR HL.
IS DRIVER LEFT OR RIGHT,? IN USA LEFT.
IS HIGH AND LOW BEAMS DEAD LEFT? No TOLD AT ALL.
PUT METER BLACK LEAD TO THE BATTERY NEG LUG
THEN PROBE RED TO ALL WIRES OF DEAD LAMP 1 BY 1.
12VDC IS GOOD 0 BAD
IF LAMP GROUND PIN READS 12VDC <<< GROUND FAILS.

LEFT LAMP USES GROUND LUG G101. IF R

CAR HAS DRL. SO DRL AND MANUAL LAMPS FAIL
HIGH , LOW , AND FLASH HIGH>? NOT TOLD
DOES ENGINE RUN? OMG NOT TOLD.
THIS CAR RUN HL RELAYS BY BCM CONTROLLER BRAIN


FUSE ARE ON THE OUTPUT OF ALL HL RELAYS
SO IF ALL FUSES INPUT(TOP) ARE DEAD,THAT MEANS
BCM IS FAILING. OR THE SWITCH TO IT.
OR FUSES BLOW TO BCM
WE SCAN THE PCM/BCM TO SE WHY.


HEAD LAMPS ON THE 4 FUSES ALL 4 RIGHT SIDE ARE
12VDC, IF NOT BCM IS MESSED UP, OR RELAY DEAD.
HE LOW BEAM RELAY RUNS BOTH SIDE
SAME WITH BEAM. A RELAY FOR IT.
DRL HOT ONLY IN DRL MODE.
DRL; HAS A SUN SENSOR (AUTO MODE)


BOTTOM HERE IS HEAD LAMPS.SIDE.

HEAD LAMPS ON USA WORK EVEN KEYOFF
SO DOES BCM TO DO THAT, MAIN BATTERY NOT DEAD

Ive changed the relay and the headlight switch on the dash .. still wont turn off headlights ? Just changing parts won't fix it , need to test . Hooking up a professional scan tool , one that can read codes in the BCM - body control module is the way to start to find the problem . Then familiarize yourself with how they work.

Headlamps
Major components of this system are the body control module (BCM), headlamp relay, beam select relay, ambient light sensor, headlamp and panel dimmer switch, turn signal/multifunction switch, park brake switch, and the low and high beam headlamps.
The headlamps may be turned ON in 2 different ways. First, when the driver places the headlamp switch in the ON position, normal operation occurs. Second, when the headlamp switch is placed in the AUTO position, automatic lamp control (ALC) operation occurs. During ALC control, the headlamps will be OFF in daylight conditions or in low/high beam operation in low light conditions.
The headlamp relay receives battery positive voltage directly from the battery. The BCM supplies a ground signal to the headlamp relay for normal headlight operation. The BCM also supplies voltage to the beam select relay coil for high beam headlight operation. When the driver places the headlamp switch in the ON position and the dimmer switch is in the low beam position, the headlamp relay supplies current flow through the left and right low beam headlamp fuses to both low and high beam headlamps. Both low beam headlights are grounded through the beam select relay. When activated, the dimmer switch sends a ground signal to the BCM in the high beam position and a momentary ground signal in the flash-to-pass (FTP) position from G106. The BCM then energizes the beam select relay which switches the headlamp grounds from the low beam headlight bulbs to the high beam headlight bulbs illuminating the high beam headlights. With the headlights in the low beam position, the high beams may be momentarily turned ON or flashed by activating the FTP portion of the switch.
The instrument panel cluster (IPC) illuminates the high beam indicator when the BCM detects that the high beams are requested. The IPC receives a class 2 message from the BCM requesting illumination.
The Headlamps On at Exit and Perimeter Lighting modes can be adjusted using the steering wheel controls to select the function as displayed in the driver information center (DIC). The Headlamps On at Exit selection will allow the driver to customize the period of time that the headlamps remain illuminated upon exiting the vehicle. This period can be adjusted from 0-180 seconds. The Perimeter Lighting feature allows the driver to select if they want the headlamps and backup lamps to illuminate when the door UNLOCK button on the key fob is activated. This feature can be turned ON or OFF by using the DIC steering wheel control buttons.

DTC B2575 Headlamp Control Circuit

Circuit Description
When the body control module (BCM) senses a request for headlamp or daytime running lamp (DRL) illumination, the BCM sends a ground signal to the headlamp relay through the low beam headlamp relay control circuit. The headlamp relay will illuminate the low beam headlamps.

Install a scan tool.
Turn ON the ignition, with the engine OFF.
With a scan tool, command the headlamps ON and OFF.
Does the headlamp relay turn ON and OFF with each command?

Do you know what bi-directional control means ? Need a professional scan tool to do these type of test .

DTC B2602: Daytime Running Lamp Control Circuit Low or Open
DTC B2603: Daytime Running Lamp Control Circuit High

Without this type of info. from service repair manual an using a scan tool your missing the big picture .

I would check the fuses first. Headlights are typically on a separate fuse then the parking lights. If the fuse is fine check and see if the Bulb is burnt out but it is rare for both lights to go out at the same time.

Sounds like a switch issue.

You can't turn them on manually with the switch . You have the switch set on auto ?
Headlamps
You can use the headlamps in two different ways.
• Place the headlamp switch in the ON position for normal operation.
• Place the headlamp switch in the OFF position for automatic lamp control (ALC). During ALC the high beam headlamps are On at reduced intensity for daytime running lamp (DRL) operation in daylight conditions, or low beam headlamps On in low light conditions.
The DRL/EXT LTS fuse and the EXT lamps fuse in the underhood junction block supply battery positive voltage at all times to both of low beam lamps and to the right high beam lamp. The low beam circuit continues to the high/low beam switch, then, depending on the position of the dimmer switch, connects to the normally-open headlamp relay switch contacts. Placing the headlamp switch in the HEAD position provides a ground path for the headlamp switch input of the Body Control Module (BCM). After receiving this input, the BCM energizes the headlamp relay. When the headlamp relay is energized, the low beam circuit is connected to ground G201. The high beam circuit is divided into a left and a right side circuit.
The DRL/EXT LTS fuse in the underhood ignition block supplies battery positive voltage to both the coil and to the normally-closed contact of the DRL relay switch circuit. During high beam operation, the left side current flow is through the closed contacts of the DRL relay, and to the left high beam lamp.
The EXT Lamps fuse in the top of the engine fuse block supplies battery positive voltage to the right high beam lamp. Both high beam circuits are then connected together, and continue to the dimmer switch. When the driver closes the high beam contacts of the dimmer switch, the circuit is grounded at G201.
Both the headlight switch and the BCM provide a ground, or control circuit, to the headlight relay coil circuit for manual or automatic headlamp operation. When you place the headlamp switch in the OFF position, and the ambient light sensor indicates low light conditions, the BCM energizes the headlamp relay for low beam operation. You may switch the headlights to high beam by pulling the dimmer switch handle toward you until the dimmer switch is activated. When the dimmer switch is placed in the HIGH position, the indicator lamp input to the BCM is pulled low. The BCM then sends a class 2 message to the instrument cluster in order to illuminate the high beam indicator lamp.
If the headlamp switch is left in the head position, the inadvertent power control feature will turn off the headlights 10 minutes after you turn the ignition switch to the OFF position. If you place the headlamp switch in the head position after the ignition switch has been turned OFF, or if the ignition switch is in the ACCY position, the headlights will remain ON until you turn them OFF or until the battery runs dead.

High beam switch moat likely, have you checked relays and fuses?

Both sides or just one? If both, The multi-function switch on the steering column is not working properly

do your flash to pass lamps light when you pull the stalk towards you? If yes, the bulbs are ok.
Do the hig beams work?
Your headlamps have sepaerate fuses for each headlamp and you have a low beam relay and a high beam relay under the hood in the black box.
If everything is out, I suspect a bad headlamp switch.
Check car-part.com and look on page with * for cheapest price.

Your owner manual will identify fuses & relays.

PS, You did not recently instal high current bulbs did you? If yes, put originals back in.

HEADLAMPS

The voltage is supplied to the lamp switch through a fuse. This fuse is located in the central junction box in the left-hand footwell.
When the headlamps are switched on, a voltage is supplied to the high beam/low beam switch and to the low beam relay. The relay for the low beam is located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "low beam", then a voltage is supplied through the low beam relay to the low beam part of the headlamp assembly. The left and right-hand low beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "high beam", then a voltage is supplied through the high beam relay to the high beam part of the headlamp assembly. The left and right-hand high beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.

----------------------------------------------------------------------------------------------------------
Lamp Switch
Removal

1. CAUTION: Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
   Remove the lower driver's side footwell trim.

1. Detach the lamp switch bezel.
   • Remove two screws.

1. Remove the light switch.
   • Remove three screws.
• Disconnect the electrical connector