2004 Ford F150 Logo
Posted on Mar 18, 2016
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

I went through programing as far as lock recycling but wont go any further

Answer This Question

1 Answer

Jeff Armer

Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

  • Ford Master 15,575 Answers
  • Posted on Mar 18, 2016
Jeff Armer
Ford Master
Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

Joined: Nov 22, 2012
Answers
15575
Questions
1
Helped
7102196
Points
73899

Remote Transmitter Programming NOTE: All keyless entry remote transmitters must be programmed at the same time.
NOTE: Programming (or reprogramming) the keyless entry remote transmitters into the central security module can be accomplished using a diagnostic tool or by carrying out the following steps.

  1. Turn the ignition switch from OFF to RUN eight times within 10 seconds, ending in RUN. If the module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after Step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the doors will lock and unlock one last time to confirm.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

What other issues can cause fob not to work beside the fob itself?
Take it to an auto electrician to have it checked for operation and reprogrammed with a scan tool computer..
Read full answer
Jan 08, 2022 • Cars & Trucks
0helpful
1answer

I programmed remote as far as lock recycle but wont go any further 2004 matrix
Contact a company call remote remote for a step by step for the reprogram. remoteremote.com
Great folks there they will help you.
Read full answer
Mar 18, 2016 • 2004 Chevrolet TrailBlazer
0helpful
1answer

98 Nissan frontier,4wd wont engage,lock in hubs manualy but they will not engage
If you have turned the lock tabs until they click in or out which ever the case may be for 4wd drive then maybe the transfer case is not selecting 4wd If it is vacuum actuated or electronic operation I would be checking their actions be for e I went any further.
Read full answer
Sep 08, 2013 • 1998 Nissan Frontier
0helpful
1answer

I have a 93 jeep cherokee country. The power window on front drivers side will not go down. it went down halfway the other day...would not go any further....went back up fine now wont work at all...i dont...
Sound like the window regulator is coming apart if there is any motor noise replace the regulator
Read full answer
Dec 27, 2017 • Jeep Cherokee Cars & Trucks
0helpful
1answer

1999 Chevy silverado z71trying to program a new key fob
Use this procedure for New Body Style.
1. Close all doors
2. Insert key into ignition
3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down
until instructed to release in step 9.
4. Perform steps 5 through 8 in a fairly rapid succession.
5. Turn the ignition to the ON position (as far as you can go without starting the engine.)
6. Turn the ignition to the OFF position.
7. Turn the ignition to the ON position (as far as you can go without starting the engine.)
8. Turn the ignition to the OFF position.
9. Release the power UNLOCK button on the door panel. The vehicle should respond by
door locks locking and unlocking automatically. (If locks do not cycle after you let go,
not before you let go of the unlock button, then the vehicle has not entered programming
mode and you must start procedure over. Remove key from ignition, open drivers door
and return to step 1 ). If the locks do cycle automatically then proceed to step 10.
10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and
unlock. This may take up to 30 seconds.
11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
12. Turn the ignition to the ON position to exit the programming mode.
13. Test remote(s).
Read full answer
Apr 29, 2010 • 1999 Chevrolet Silverado 1500
1helpful
1answer

My door locks on the passenger side wont work, and my interior lights wont turn off, the windows also wont work. I have a 2002 jeep grand cherokee
you have a broken grond wire in the front pasanger door boot in the front door jam. very common on these and have to repair thwm all the time. you have to pull back the black boot and inspect all the wires and pull on the. sometime the break is up further and you can't see it because the boot don't pull back far enough. it most likely with be a black wire. good luck
Read full answer
Mar 14, 2010 • 2004 Jeep Grand Cherokee
0helpful
1answer

1999 Sonata lock code changed
the remote programming may have been erased-with the doors locking automatically it is a feature that should be able to be changed-you will have to check the owners manual on how to change that feature
as far as the remote-you will have to contact a hyundai dealer about reprogramming the remote-it may also just need a battery
Read full answer
Feb 18, 2010 • 1999 Hyundai Sonata
0helpful
1answer

Need to re-program 2000 Chev.C3500 key fob need help
1. Close all doors
2. Insert key into ignition
3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down
until instructed to release in step 9.
4. Perform steps 5 through 8 in a fairly rapid succession.
5. Turn the ignition to the ON position (as far as you can go without starting the engine.)
6. Turn the ignition to the OFF position.
7. Turn the ignition to the ON position (as far as you can go without starting the engine.)
8. Turn the ignition to the OFF position.
9. Release the power UNLOCK button on the door panel. The vehicle should respond by
door locks locking and unlocking automatically. (If locks do not cycle after you let go,
not before you let go of the unlock button, then the vehicle has not entered programming
mode and you must start procedure over. Remove key from ignition, open drivers door
and return to step 1 ). If the locks do cycle automatically then proceed to step 10.
10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and
unlock. This may take up to 30 seconds.
11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
12. Turn the ignition to the ON position to exit the programming mode.
13. Test remote(s).
Read full answer
Jun 09, 2009 • 1999 Chevrolet Tahoe
4helpful
4answers

1998 Honda Accord Sunroof wont close all the way
I took mine in expecting to have it repaired and it turns out that it was just the screws along the left and right-hand side of the panel.  They were loose.  The guy told me that "it eventually happens" and that "it's only a matter of time".  He went on to say that "it shouldn't happen again".  So, check the screws on either side of the panel right where it's stopping.  I suspect that this is prohibiting yours from closing as well.

HTH!
Read full answer
Feb 24, 2009 • 1998 Honda Accord
3helpful
1answer

2001 pontiac sunfire wont start
I have had the exact same problem. There is an ignition lock that probably went off. There is a fuse box under the hood. The fuse that says ignition on it pull it out and put it back in. This should reset the ignition lock. Its a safety feature because the car thinks that someone was trying to tamper with it.
Read full answer
Dec 03, 2008 • 2001 Pontiac Sunfire
Not finding what you are looking for?

View Most Popular

2004 F150

  • Cars & Trucks

Related Question

What other issues can cause fob not to work beside the fob itself?

  • Cars & Trucks

Related Topics

406 views

Ask a Question

Usually answered in minutes!

Popular Questions

Diagram for ford f 150

Ford F-150 Cars & Trucks

Diagram of front end for '94 F150 Ford

1994 Ford F150 Styleside Supercab

Firing order for 1994 f150 v8 302 engine

1994 Ford F150 Styleside Supercab

93 to 95 Ford F-150 V-8 engine....firing orders!

1993 Ford F150 SuperCab

I need an F150 trailer towing wiring diagram.

2001 Ford F150 Styleside SuperCrew

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Ford Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
Manual. user-manual-2004 F150 Manual

2004 F150

Loading...