Question about 2008 Cadillac Dts

1 Answer

How do i replace right front turn signal bulb on 2008 cadillac dts

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cadillac Master
  • 5,274 Answers

My automotive database says you have to remove headlamp assembly to replace bulb. To remove headlamp assembly, you need to remove front bumper fascia.
Why in the world should you have to remove front of vehicle just to change a bulb, I don't know? My database is the only info I have to go by. I doubt I can walk you through it, step by step, I can't see anything from here.

Posted on Mar 01, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Cadillac SRX Why do right turn signals flash much faster than left? All bulbs are illuminated.


The turn signals on your vehicle are computer controlled by the BCM - body control module . The first place to start would be to hook up a scan tool that can access BCM DTC'S an data Parameters. If all the turn signal bulb's are good .
Turn Signal Lamps
Ground is applied at all times at G201 to the turn signal/multifunction switch. The turn signal lamps may only be activated with the ignition switch in the ON or START position. When the turn signal/multifunction switch is placed in either the TURN RIGHT or TURN LEFT position, ground is applied to the body control module (BCM) through either the right turn or left turn signal switch circuit. Battery voltage is applied at all times to the BCM. The BCM then applies a pulsating voltage to the front and rear turn signal lamps. Ground for the front turn signal lamps is supplied at G104. The left rear turn signal lamp is supplied ground at G402 and the right rear turn signal lamp is supplied ground at G401.
High resistance some where in the turn signal circuit could also cause this type problem . Doing voltage drop testing on the circuit would find a problem of high resistance .

High Mastering Voltage Drop Testing with Pete Meier and Jerry Truglia

Oct 19, 2016 | Cadillac Cars & Trucks

1 Answer

Replace right front turn signal bulb


You may be able to access it from the engine compartment, or from under the car. There's a twist-out buld socket - (twist about an 1/4 quarter turn to the left) - then pull striaght back. If not accessable that way remove the light cover/lens and then the light unit - there should be enough slack in the wires to pull the assembly forward alittle to remove buld socket.

Aug 01, 2014 | 2007 Cadillac DTS Sedan

1 Answer

How to change the signal lights


one of the three of them is blown,turn it on with car parked and see which light is out

Apr 25, 2014 | 2007 Cadillac DTS Sedan

1 Answer

How to change front turn signal bulb on 2008 SRX Cadillac


Nope don't need to drop the whole light assembly. I just took the wheel and inner cover off, then the 6 torx screws that hold the light hosing together , replaced the turn signal bulb and good to go!!

Mar 04, 2013 | 2004 Cadillac SRX

1 Answer

How do i replace the fuse for the front turn signal on 2006 cadillac srx


The socket is defective?? Probe the socket with a volt meter to see if voltage is turning on and off to trigger the bulb to flash.

Jul 09, 2012 | 2006 Cadillac SRX

1 Answer

Change turn signal bulb 2008 srx


Front turn signal bulb replacement 2008 SRX . Jack up car & block . Remove front wheel & front half of the wheel house assemble. There are about 7 plastic pull rivets that have to be removed . Pull out the wheel house . Remove turn signal & driving light cover held on by 6 # T10 torx screws . Twist out socket & replace bulb # 3757NAK . Should take about 45 min.

Mar 26, 2012 | 2006 Cadillac SRX

1 Answer

Passenger side brake light & signal not working


Hello! The Right Stop/Turn Signal are the same bulb...The most obvious answer is to replace the bulb...But if you have done that without success let me know and I'll find the fault....Guru....saailer

I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

Oct 30, 2011 | 2007 Cadillac DTS Sedan

2 Answers

2007 cadillac dts passenger side rear brake light is not working


If the turn signal is blinking fast on the dash then this means that the bulb is blowned outside of the vehicle. Check to see that all of your exterior turn signals are lighting up and if not then it's time to replace the bulb(s). Hope this was helpful to you

Oct 30, 2011 | Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

223 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...