Question about 2008 Cadillac Dts

Open Question

Replace right front turn signal bulb - 2008 Cadillac Dts

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: Replacing front turn signal bulb on 2006 Cadillac SRX

wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.

Posted on Jan 25, 2009

Ad
  • 1 Answer

SOURCE: Front turn signal bulb replacement

In your manual on page 5-53 it states how to change the bulb out
for the turning signals - we had the drivers side out. Gave it to our mechanic and had it completed in about 2 hours.

Posted on Feb 23, 2009

  • 1 Answer

SOURCE: 2004 CTS Cadillac front passenger turn signal bulb is out.

Actually no you don't. Crank your steering wheel all the way to the right so yo have the maxumum clearance for your hands and arms in the front of the wheel well. Remove the plastic clips that hold the wheel well splash guard and pull it back enough to allow access to the interior of your bumper.
Replace bulbs as needed.
Yes, a jack is nice and makes it a touch easier to access, but I did this in an AutoZone parking lot during a cross country road trip.
5 mins tops to complete.

Posted on Mar 14, 2010

Zeevert
  • 373 Answers

SOURCE: procedure to change turn signal light bulb on a

Remove 3 or 4 of the plastic pins holding the inner fender. They are located around the lip of the fender opening. The pins are removed by pulling the center cap of the pin straight out about an 1/8" and then wiggle and pull the whole pin out.
Pull the inner fender down and back.
Reach your arm in and grab the socket and squeeze the locking tab.
Rotate the socket counter-clockwise less than a quarter turn, and pull straight back.
Reach your other hand in and remove the bulb by pulling it straight out of the socket. It takes a 3157 bulb

Posted on Jun 22, 2010

Testimonial: "Thank you so much for your help. Really I had ask the question about 3 months ago, but since I didn't had it fixed yet, it's OK now. Franco"

  • 1 Answer

SOURCE: Need to replace the right front turn signal bulb

I called the dealer,They wanted $85 an hour,an two hours to do it!!!!I took the front splash guard off under the front ,Just put on with plastic plugs,Then took the inner fender well off also with plastic plugs.Turned the wheel in,I didn't have to remove it.. and used a screw driver to take a cover off to get at the bulb..It took some time and it was not easy to get at.But it was warm outside when i did it,and saved afew bucks too!!Be patient and its really not that hard.I've done it twice......

Posted on Jan 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My right front turn signal on my 2001 ford ranger doesnt work and my inside right turn signal light on dash doesnt work and flashes really fast. Buld on right side was replaced and works when lights


was the correct bulb used? this sounds like a single function bulb was used NOT the bulb that will light with the headlights and ALso produce turn singles

Dec 06, 2014 | 2001 Ford Ranger Regular Cab

3 Answers

Fast flashing turn signals


I would change out the turn signal bulb on the right front. A blown bulb can cause the fast flash issue. The signals staying on is not related to the bulb being blown. That is most likely a problem with the multifunction switch, the knob you use to signal.

Jul 12, 2013 | Buick Cars & Trucks

2 Answers

Brake light and right turn signal come on at same time


You put in the wrong bulb and it's feeding back.

Feb 02, 2018 | 2003 Jeep Liberty

2 Answers

Need replace turn signal bulb


YOU HAVE TO THE FRONT HEADLIGHT HOUSING TO REPLACE THE TURN SIGNAL BULB.

Aug 24, 2009 | 1996 Chevrolet Cavalier

2 Answers

Front right turn signal


i had a bad socket that was my problem on mine.

Dec 10, 2008 | 2000 Oldsmobile Intrigue

1 Answer

2000 Accord turn signal problem


either the front or the rear turn signal bulb is blown, that is why the flash frequency is high. replace the bulb and the problem will be solved. best to replace both the front and rear turn signal bulbs. good luck.

Aug 29, 2008 | 2000 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...