What's the cost to replace l/f door entry pad

Remove inner door panel and look while helper operates pad. Probably unlock solenoid needs lube or replacement.

Fuse #8 on the interior fuse panel and 20amp on the engine compartment fuse box, but if either of these were blown you would have several other things not working, door locks from any switch, dash board wouldn't light up, cluster radio heater control and d o on.if all this is working, I would start my testing at the door pad.they get little cracks in them over time and water gets inside and corrodes the switch, pad, internally. .ive done a lot up hete on east coast. .

Entry Code The system (permanent) entry code is located in three places:

• on the owner's wallet code card (in glove compartment)
• electronically accessible by requesting the remote anti-theft personality module KEYCODE PID on the New Generation Star (NGS) Tester 007-00500 or equivalent.
• on the remote anti-theft personality module housing

The remote anti-theft personality module is programmed at the factory with a five-digit entry code. A replacement remote anti-theft personality module includes replacement labels and a new owner's code card.
Remote Anti-theft Personality (RAP) Module C253
Above the drivers side footwell, directly above the accelerator pedal

need to notify dealer for original code have vin and proof of ownership of vehicle available

If the remote batteries are low the car will tell you on the information center by the speedometer. The door handle on the keyless entry is malfunctioning. You must replace the door handle. It usually cost around $160 plus shipping cost. Sometimes the contacts within the keyless entry become corroded or broke. Nevertheless, you need to replace it or have someone replace it. There is one screw behind the weather scrip that holds it in place. You will need a torex wrench to remove it.

You can take your registration and driver license to a dealer and they can use their diagnostic tool to retrieve it from the computer. It should cost 1/2 hour of labor. Call first & ask.

Also, look in glove box for a plastic "credit card" with the code on it.

does the key pad light when you press a button at night? If yes, the fuse is ok.
Do you have the plastic card with the permanent code in your owner manual packet? If yes, tryit.
report back.

Keyless Entry The keyless entry keypad is hardwired to the GEM. The GEM interprets the inputs from the keyless entry keypad and then controls the associated operation. The keyless entry keypad will be illuminated for five seconds when any button is pressed. Additionally, it will request the illuminated entry feature to turn the courtesy lamps on. If a lock all doors code is entered, the illumination will turn off, as well as request the illuminated entry feature to turn off the courtesy lamps. When pressed, the keyless entry keypad supplies the ground signal to the GEM or the GEM receives a signal from the keyless entry remote transmitter. Then the GEM outputs a ground signal to the appropriate lock or unlock relay which supplies the power to the actuator to lock or unlocks all doors, including the luggage compartment. The keyless entry remote transmitter also unlocks the liftgate or activates the panic alarm by sending a signal to the GEM.
--------------------------------------------------------------- Visual Inspection Chart Mechanical Electrical

• Keyless entry keypad
• Keyless entry remote transmitter

• Central junction box (CJB) Fuse F222 (20A)
• Circuitry
• Generic electronic module (GEM)

------------------------------------------------------------------------

• No communication with generic electronic module (GEM)

• Generic electronic module.
• Circuitry.

• REFER to Section 419-10 .

------------------------------------------------------------------------------------

Hello
this is how to program the remotes/keyless entry

How

• Obtain all remote transmitters
• enter the 5 digit permanent code into the keyless entry pad on the drivers door
• Press the 1-2 switch on the keyless entry pad
• Within 5 seconds
• Press any button on the first remote transmitter
• The doors should open then lock
• Within 5 seconds
• press any button on the second & third remote
• within 5 seconds for each remote
• to exit programming
• simultanionusly press 7-8 & 9-0 switchs on the key pad or wait more then 7.5 seconds

NOTE
The 5 digit permanent code is located in one of the following places

1. On the owners warranty card
2. On the label on the inside the trunk/ boot
3. On the owners code card
4. On the centrel locking control module located in the drivers door
5. In the PCM ford can get this for about $25.00

I hope this help
Regards Paul
www.limotec.co.uk

Doubt its a fuse. Most likely the key pad has failed and needs to be replaced. On the bright side this is a good problem to have and you have a very reliable car.

the keyless entry pad may be an add on from the dealer which was just stuck on therefore comtains a battery need to remove the door panel and check for wires from pad