At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
It does indeed have keyless entry. It needs reprogramming when you get a new remote. Also if you disconnect the battery. Usually a local car alarm fitting shop, or an auto-electrician will do it. Plus of course a Ford dealership.
You can reset Your system by turning Your Key on and off several times and you should hear the doors lock and unlock.. you will need to this really fast/ On and Off and On and Off and On and Off . Then You should be able to set Your remote control numbers it will be a 4 digit code.. give it a try..
I own a 2007 Buick Lacrosse, but I imported it to Paraguay, South America. Now I bought a new Engine Start Keyless Entry Remote from Amazon, but here we do not have any GM dealer to program the unit.
I really need help to program the keyless remote control, I will appreciate very much your help.
To program ( or reprogram ) a keyless entry remote transmitter into the remote keyless entry module, perform the following steps:
1. Turn the key to ON or ACC and short the two terminals of the program connector, a two-pin connector located below the driver's side of the instrument panel at the base of the steering column. All doors should lock and then unlock. 2. Press any button on each keyless entry remote transmitter in turn. All doors should lock and then unlock. If the door locks do not respond, press the button again (up to three times maximum with the same keyless entry remote transmitter). If the door locks still fail to respond, go to Pinpoint Test A. 3. Repeat Step 2 to program additional keyless entry remote transmitters into the remote keyless entry module (up to four keyless entry remote transmitters maximum). 4. Turn key off. 5. Remove the short from the program connector. All doors should lock and then unlock. 6. Verify that the keyless entry remote transmitters have been successfully programmed by pressing the LOCK or UNLOCK button on each one, and observing that the system responds by locking and/or unlocking the doors.
Programming Electronic Door Lock Control System
NOTE: The electronic door lock control processor (14B001) erases all
previous keyless entry remote transmitter (15K601) from memory when the keyless
entry remote transmitters are programmed or reprogrammed. The electronic door
lock control processor can store up to four keyless entry remote transmitters in
memory.
To program (or reprogram) keyless entry remote transmitter into the
electronic door lock control processor, perform the following steps:
Turn ignition switch to the RUN position and momentarily short the two
terminals of the program connector taped to the wire assembly and located behind
the glove compartment. All doors should lock and then unlock. Remove shorting
pin.
Press any button on keyless entry remote transmitter. All doors should lock
and then unlock to verify the keyless entry remote transmitter has been
programmed. If door locks do not respond, press button again (up to three times
maximum with the same keyless entry remote transmitter).
Repeat the above step to program additional keyless entry remote transmitters
into the electronic door lock control processor (up to four keyless entry remote
transmitters maximum).
Turn ignition switch OFF. All doors should lock and then unlock.
security module in the trunk ???? There is no security module in the trunk . What light's come on by them self ? Park lamps , headlamps , brake lamps ,turn signals etc.... The module for anti-theft is under the right hand side of the dash . The remote keyless entry module is located in the trunk.
Is this the part you hear clicking in ?
Door Lock Control Processor, Electronic
NOTE: The electronic door lock control system will not function when the ignition switch is in the RUN or ACC position.
The electronic door lock control processor:
is located on the LH side of the luggage compartment.
contains a radio receiver that receives a signal from the keyless entry remote transmitter (15K601) through electronic door lock control processor antenna, and sends the appropriate command to the power door locks, the horn relay, the indicator flasher, or the anti-theft warning system.
is equipped with a battery backup which holds the programmed code in memory in the event the vehicle battery is disconnected.
Doors Do Not Lock or Unlock Using Keyless Entry Remote Transmitter
The sounding alarm maybe a security system installed by in the truck. Disconnecting the battery will only temporarily solve your problem, but will resume once you reconnect the battery for electrical power.
You must find the keychain/remote of the security system and disable it. If you are unable to locate this, you can have it disconnected by a qualified automotive electrician.
Word of caution though, if you are using the keyless entry system with the security system, this will be disabled until you install a receiver with such function.
This bulletin supersedes TSB# 02-90-001.
DESCRIPTION:
The security system keyless adapter cable (SPX/Kent-Moore P/N 09900-21300) is a special service tool (SST) that is used for programming new keyless entry remote transmitters to the factory security systems. The keyless adapter is used in conjunction with the Hi-Scan Pro (with Hi-Scan SOL Pro Software Version 09-29-03 or newer) and Data Link Connector (DLC) Cable.
SERVICE INFORMATION:
The keyless adapter cable can be used on the following vehicles:
2001 - 2004 MY Elantra
2001 - 2004 MY Santa Fe
2002 - 2004 MY Sonata
2001 - 2004 MY XG300/350
NOTE
The 2003 - 2004 MY Tiburon does not need the Keyless Adapter Cable to add keyless entry remotes to the factory security system. Instead, the Hi-Scan Pro connects to the vehicle using only the DLC cable. See page BE-60 in the 2004 MY Tiburon Shop Manual for the latest instructions.
The most current Keyless Adapter Cable Instructions are available in the following shop manuals:
SHOP MANUAL
PAGES
2004 MY Elantra
BE-73 - BE-74
2004 MY Santa Fe
BE-43 - BE-44
2004 MY Sonata
BE-40 - BE-41
2004 MY XG350
BE-46 - BE-47
KEYLESS ADAPTER CABLE INSTRUCTIONS:
Connect the keyless adapter cable to the Hi-Scan Pro DLC cable.
Plug the keyless adapter into the vehicle's 10-pin multi-purpose connector located behind the driver's side lower instrument panel (next to the DLC).
NOTE
Sample vehicle shown is the Santa Fe.
Turn the Hi-Scan Pro ON and press ENTER .
NOTE
"Release date 29. Sep. 2003" OR LATER must appear on this screen. To update your SOL card with the latest software go to www.hmaservice.com and refer to TSB 00-00-001.
Select option "HYUNDAI VEHICLE DIAGNOSIS" and press ENTER .
Select vehicle model and press ENTER .
Select option "TRANSMITTER CODE SAVING" and press ENTER .
Ensure that the key has been removed from the ignition cylinder before proceeding.
Follow the steps noted on the Hi-Scan Pro screen to program the remote(s).
NOTE
The factory security system can only be programmed to accept two remote transmitters and MUST be programmed for both remote transmitters at the same time.
Press ESC on the Hi-Scan Pro and verify that the remote(s) are functioning properly.
Turn the Hi-Scan Pro OFF and disconnect the adapter cable from the multi-purpose connector.
×