How do I remove panel to replace liftgate switch, please?

2008 Saturn Vue liftgate will not open

The endgate/liftgate can be locked or unlocked by operating either one of the front door lock switches, your's doesn't do this ?
Endgate/Liftgate
Once the vehicle doors have been unlocked, the endgate/liftgate can be opened by using the handle mounted to the exterior of the gate. The endgate/liftgate can be locked or unlocked by operating either one of the front door lock switches, or by pressing the Lock/Unlock button on the key fob. The endgate/liftgate lock and unlock functions operate in conjunction with the rear doors.

1.Open liftgate before disconnecting battery.
2.Open hood, disconnect and isolate the battery negative cable.
3.Open liftgate.
4.Disconnect the power liftgate prop rod.
5.Remove liftgate trim panel
6.Remove the four retaining nuts to spoiler .
7.Gently lift spoiler off of outer liftgate panel.
8.Disconnect the CHMSL electrical connector.
9.Disconnect the washer hose.
10.Remove spoiler from vehicle.
11.If replacing spoiler, transfer CHMSL lamp to new spoiler.
12.If replacing spoiler, transfer washer nozzle to new spoiler.

There is a known TSB for this....
#07-08-52-003: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE)/Key Fob Transmitter/Door Lock Switch, Lifgtate Hatch or Liftgate Glass May Lock/Unlock When Rear Liftgate Glass Button Depressed - (Sep 13, 2007)


Subject: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE), Key Fob Transmitter or Door Lock Switch, And/Or Liftgate Hatch Or Liftgate Glass May Lock Then Unlock When Rear Liftgate Glass Button is Depressed (Reposition Lock Cylinder Wave Washer and Adjust Lock Rod)


Models: 2005-2007 Buick Rainier

2005-2008 Chevrolet TrailBlazer, TrailBlazer EXT, TrailBlazer SS

2005-2008 GMC Envoy, Envoy XL, Envoy Denali

2005-2008 Saab 9-7X




--------------------------------------------------------------------------------
Do This
Don't Do This

Reposition liftgate lock cylinder wave washer and adjust lock rod.
DO NOT replace the liftgate latch or actuator.


Condition
Some customers may comment on one or more of the following conditions:

• The rear liftgate glass may not lock when using the remote keyless entry (RKE), key fob transmitter or door lock switch unless the lock is pressed a second time.

• The rear liftgate or glass locks, but may be unlocked when the rear liftgate lock cylinder button is depressed.

• The rear liftgate locks but the liftgate glass may not lock.

Cause
These conditions may be caused by one or all of the following:

• The rear liftgate cylinder lock rod may be out of adjustment.





• The wave washer on the liftgate lock cylinder may be out of position with the cup side down.

• Excessive movement or slack in the lock rods at the liftgate bell crank assembly.





• The liftgate lock cylinder pawl may contact the rear liftgate glass latch when the lock cylinder button is depressed.

Correction
Important: Do Not remove the rear liftgate lock cylinder from the vehicle to perform this repair.

Reposition the rear liftgate lock cylinder wave washer and adjust the lock rod using the steps below.

Verify the customer's condition.

Open the liftgate.

Remove the upper liftgate garnish molding.

Remove the rear liftgate trim panel.

Remove the cylinder lock rod from the threaded lock rod retaining clip.

Tip
Place the tip of a screwdriver blade into the opening of the C-clip and slowly rotate the screwdriver to pry out the C-clip from the shaft. Then use needle-nose pliers to remove the C-clip.

Remove the C-clip from the rear liftgate lock cylinder push button and remove the wave washer.

Install the wave washer with the cup side up.

Position the wave washer with the curved edges of the wave spring parallel to the tabs on the lock cylinder shaft.

Important: Use needle-nose pliers to slightly squeeze the C-clip back into shape. Make sure the clip seated, you should feel a snap and hear an audible click.

Install the C-clip onto the shaft and in the slot using needle nose pliers. Then rotate the pawl several times to make sure the C-clip does not rotate. If the clip rotates then the clip is not fully seated.

Position the lock cylinder pawl to the full clockwise position.

Pull up on the cylinder lock rod to remove any slack in the bell crank.

Install the cylinder lock rod into the threaded lock rod retaining clip while removing any slack from the lock rod linkage.

Close the lock rod retainer clip.

Close the liftgate assembly.

Open the liftgate glass while keeping the liftgate closed.

Use the key fob to cycle the liftgate to the lock and unlock position while inspecting the rear liftgate pawl. The lock cylinder pawl should have clearance between the latch as shown above. If the pawl is contacting the latch, readjust the cylinder lock rod.

Verify that the customer's condition has been corrected.

Install the rear liftgate trim panel.

Install the upper liftgate garnish molding.

{: ) Liftgate Access Plug is located at the bottom center area of the liftgate trim panel.
From inside the vehicle lower the second and third, if applicable, row seats.
Use a small flat-bladed tool to remove the access plug from the liftgate lower interior trim panel. It is like a round and smooth plastic grommet.
Push on a silver lever located on the right just through the access hole to unlock the liftgate.
Open the liftgate from the outside of the vehicle using the exterior handle.

Remove the liftgate pull handle. Refer to Liftgate Inside Pull Handle Replacement .
DO NOT attempt to remove the liftgate trim panel if there is a failure of the electric latch. Refer to Opening the Liftgate Without Electrical Power .
1
Liftgate Trim Finish Panel
2
Liftgate Trim Finish Retainer Clips (Qty: 2)
3
Liftgate Lower Trim Finish Panel
4
Liftgate Trim Finish Retainer Clips (Qty: 14)

There is a switch, most likely built into the latch, that tells the body control module when the liftgate is open or closed. If that fails what you experience will happen. An open / shorted wire or bad BCM or overhead panel will also cause the "liftgate open" indicator to be on. Try and locate the switch and look for obvious damage.

how to i open a stuck lift garte on a ford winstar 2000 lock broken too

The liftgate consists of the following components:

• liftgate door lock actuator
• liftgate lock cylinder (if equipped)
• liftgate window glass
• liftgate window latch/ajar switch
• liftgate window glass release handle
• liftgate latch remote control which consists of the following component:
  • liftgate release handle
• liftgate latch, which consist of the following component:
  • liftgate latch door ajar switch

Liftgate Latch Actuator Removal and Installation

1. Remove the liftgate latch remote control. For additional information, refer to Liftgate Latch Remote Control in this section.

SECTION 501-14: Handles, Locks, Latches and Entry Systems 2001 Escape Workshop Manual
REMOVAL AND INSTALLATION Liftgate Latch Removal and Installation

1. Remove the liftgate trim panel.

1. Disconnect the liftgate ajar switch electrical connector.

1. Disconnect the liftgate latch actuating rod.
   1. Open the clip.
   1. Disconnect the actuating rod.

1. Remove and discard the liftgate latch bolts.

1. Remove the liftgate latch.

1. NOTE: Make sure the liftgate latch release rod is not preloading the latch. It should be clipped in a relaxed state with no slack.
   NOTE: Position the liftgate latch release rod by pushing outboard to remove the slack.
   

1. Remove the screws and the liftgate latch actuator

Had same problem on Ford Escape, Could not unlock the rear liftgate or window, if you can open you are in better luck.
If it is locked and closed, you will have to pull the top portion of the plastic trim away from the liftgate, it is held in place by metal retaining clips on top, and four screws on the bottom, if you can open, remove the screws then remove the rest of the panel, if unable, pull the top of the panel just far enough to reach in and unlock the liftgate.
Once you have the gate open and the panel off, you will see the locking actuator connected to the electrical connetion, it is a little bit smaller then a pack of cigarettes with a black lever.

To remove you will need to remove the two outter 10mm nuts holding the "brass" colored assembly, you will probably have to disconnect the two lever connections to get to the back side of the brass assembly, once this is done, you can use a T-20 torx to remove the locking actuator, part number stamped on my part was 4510 5424 made by KIEKERT although a search of this part didnt give me any good results, anyway, that was the cause of my problem, once replace and all put back together everything worked fine.