Where is the fuse for my driver seat? Does it operate both seats

Check for battery power on the orange wire pin D and ground (black wire) pin C- Brown wire pin B should be ignition hot on connector C1 on the Driver Climate Control Seat Module located under the driver seat. If you have power and ground, you may need to use a scan tool to see if there are any codes stored in the module. If the scan tool is unable to communicate with this module, it could either be a bad module or a network problem. If you are missing either battery, ignition hot, or ground- then repair as needed

unplug it or pull fuse

DRIVER SIDE OPERATION Power is supplied at all time ? through 50A fusible link (letter F , located in the fuse and fusible link box) ? to driver seat control unit terminal 1. ? through 10A fuse [No.21, located in the fuse block (J/B)] ? to driver seat control unit terminal 8.

Not a fuse issue , more then likely a burnt heating element in the seat , happens all the time .
Heated Seat Components
The heated seat system consists of the following components:
• Driver and passenger heated seat switches
• Driver and passenger seat back heater elements
• Driver and passenger seat cushion heater elements
• Driver and passenger seat back temperature sensors
• Driver seat module
• Driver door module
• Passenger door module

The control module have a Battery voltage supply , the module supply's voltage to the seat heating elements .
The heated seat switches are momentary contact switches and are inputs to the driver and passenger door modules. Battery voltage is supplied to the switch assembly from the door module, and when a heated seat switch is pressed and released a brief switch signal voltage is supplied to the door module. Whenever the door module receives an active heated seat switch input, the next heated seat operating mode is determined by whatever the current mode may be. The seat heater elements are controlled by the driver seat module using inputs from the door modules through Class 2 serial data circuit messages. The driver seat module controls the voltage supply and the ground circuits to the seat heater elements. When a heated seat function is commanded active, the seat module will switch battery voltage to the heater element supply circuits, and ground is provided through low side drive control circuits. During heated seat operation both the seat back and cushion heater elements are supplied battery voltage. The seat module grounds the appropriate control circuits for back only or back and cushion heating modes, and opens or closes the active control circuits as necessary in order to maintain the desired seat temperature. The seat module relies on inputs from thermistors located in the driver and passenger seat backs to control heated seat temperatures. The thermistors are 2 wire sensors supplied with a 5-volt referenced signal circuit and a low reference circuit from the seat module. Resistance through the thermistors varies with temperature causing the heated seat sensor signal circuit voltage levels to decrease as the seat back temperatures rise. The seat modules allow heated seat operation only while the engine is running which is determined by a Class 2 serial data circuit message from the powertrain control module.

Your best bet , take it to a qualified repair shop.

Heated Seats
This system allows the electrical heating of the front seats on passenger demand.
The components of the system are:

• the seat heating elements located in the seat cushion and backrest.
• the heated seat control switch, located on the seat side trim panel.
• temperature sensors located in the seat cushion heating elements.
• heated seat relay.

Do both front seat heaters not work ? Do you know how to test electrical circuits with voltmeter ?
PINPOINT TEST J: THE HEATED SEAT IS INOPERATIVE Test Step Result / Action to Take J1 CHECK HEATED SEAT SWITCH OPERATION

• Key in ON position.
• Press the heated seat switch on the driver and passenger seats.
• Are both heated seat switch indicators illuminated?

Yes
If both indicators illuminate, Go To Pinpoint Test K . If only one indicator illuminates, GO to J5 .

No
GO to J2 . J2 CHECK THE HEATED SEAT RELAY CIRCUITS

• Key in OFF position.
• Disconnect: Heated Seat Relay C3250 (located under the driver seat).
• Key in ON position.
• Measure the voltage at heated seat relay C3250-86, circuit 1003 (GY/YE), harness side and ground; and between C3250-30, circuit 566 (DG), harness and ground.
  
• Are the voltages greater than 10 volts?

Yes
GO to J3 .

No
REPAIR inoperative 1003 (GY/YE) or 566 (DG) circuit. TEST the system for normal operation. J3 CHECK HEATED SEAT RELAY GROUND CIRCUIT

• Key in OFF position.
• Measure the resistance between heated seat relay C3250-85, circuit 57 (BK), harness side and ground.
  
• Is the resistance less than 5 ohms?

Yes
GO to J4 .

No
REPAIR circuit 57 (BK). TEST the system for normal operation. J4 CHECK THE HEATED SEAT RELAY

• Install a fused jumper lead between heated seat relay 3250-30, circuit 566 (DG), harness side and heated seat relay C3250-87, circuit 1064 (YE/LB), harness side.
  
• Do both heated seat indicators illuminate when pressed?

Yes
INSTALL a new heated seat relay. TEST the system for normal operation.

No
REPAIR circuit 1064 (YE/LB) to switches. TEST the system for normal operation. J5 CHECK INOPERATIVE HEATED SEAT SWITCH INPUT

• Key in OFF position.
• Disconnect: Heated Seat Switch C320 (Driver) or C321 (Passenger) for the inoperative heated seat.
• Key in ON position.
• Measure the voltage between heated seat switch C320-2 (driver) or C321-2 (passenger), circuit 1064 (YE/LB), harness side and ground .
  
• Is the voltage greater than 10 volts?

Yes
GO to J6 .

No
REPAIR circuit 1064 (YE/LB). TEST system for normal operation. J6 CHECK CIRCUIT 57 (BK) FOR AN OPEN

• Measure the resistance between heated seat switch C320-4 (driver) or C321-4 (passenger), circuit 57 (BK), harness side and ground.
  
• Is the resistance less than 5 ohms?

Yes
INSTALL a new heated seat switch. TEST the system for normal operation.

No
REPAIR circuit 57 (BK). TEST the system for normal operation It's not that simple , being a fuse . It's probably the relay or the heating element .
PINPOINT TEST K: SEAT DOES NOT HEAT BUT THE HEATED SEAT INDICATOR ILLUMINATES WHEN PRESSED ? Does it ?
Your best bet would be to take to a qualified repair shop .
Do

The dirver seat module is attached to the underside of the seat frame. It must be calibrated if replaced. The dealer can use a tool to get failure codes (DTCs) from teh module. 1/2 hour labor charge to extract codes.


Front Seats
The front seats have the following features:

• Driver memory
• Power lumbar (optional)
• Manual lumbar
• Horizontal, vertical front and rear tilt adjustments (driver)
• Horizontal, vertical front tilt adjustment (passenger)
• Power recline
• Climate controlled (optional)

Adjustment of the seat may be accomplished with the seat control switch located on the side of the seat.
--------------------------------------------------------------------
Principles of Operation
Driver Power Seat - Memory
NOTE: The memory power seat track may stall when operating at 0°C (32°F) or below. Once the vehicle's interior temperature rises above 0°C (32°F), normal operation should return.
The driver power seat is controlled by the driver seat module (DSM). The DSM does not need to be configured, however the driver seat does need to be calibrated when the DSM is installed. The driver seat control switch provides voltage to the DSM when activated. The NEUTRAL position of each driver seat control switch position is a ground state through the seat control switch contacts. A voltage input causes the DSM to power the appropriate motor until the input is removed. Ground is the normal state of the motor circuits through the DSM and is not switched to control the motors. The DSM internally switches the appropriate line from ground to power to adjust the motors.
As the seat is adjusted, the DSM constantly monitors the motor position sensors to record the current seat position. The DSM will remove power from the motor upon termination of the seat control switch input or if the DSM does not see movement from the motor by monitoring the position sensor. The DSM must be calibrated to the seat track it is controlling. For additional information, refer to Seat Calibration. Once the DSM is calibrated to the seat track, it will only allow movement within the calibrated range.
Seat Calibration
The DSM is calibrated using a diagnostic tool. The calibration procedure automatically powers the driver power seat through its full range of motion and records the FULL STOP positions by monitoring the motor position sensors. Once the FULL STOP positions or range of the seat have been recorded, the DSM will only operate within the calibrated range. Any input attempting to drive the seat beyond the calibrated range will be ignored. This calibration is used for all seat control functions including manual switch control and memory recall positioning. During the seat calibration, the DSM may identify a function that is inoperative, such as a position sensor not changing. If the DSM identifies a concern that has a related diagnostic trouble code (DTC), the DSM will set the related DTC at the end of the validation procedure.
The calibration procedure powers the seat track adjustments to the end of their travel, which is determined by the DSM sensing a change of state in the motor position sensors. If there is a concern with the seat track or motor position sensor that limits the travel, the DSM will interpret the stopping point as the end of travel and store the position. The DSM is not able to determine if the seat has moved to its FULL TRAVEL position. It is only capable of monitoring and storing the amount of travel seen by the position sensor changing states.
For additional information on carrying out the power seat calibration procedure, refer to the diagnostic tool operating manual.
Memory Seat
Memory seat positioning can be recalled with the memory switches on the driver door panel or a programmed remote keyless entry transmitter. In either case, the DSM receives a memory recall 1 or 2 command from the driver door module (DDM) over the SCP communication network. The memory recall switches are a hardwired input to the DDM. The DDM also receives the remote keyless entry transmitter signals. Once a valid memory recall command is received from the DDM, the DSM moves the driver seat to the position stored in memory by powering the appropriate motors and monitoring the motor position sensors until the position is reached.
This system allows automatic positioning of the driver seat to 2 programmable positions.

• To program position 1, move the driver seat to the desired position using the seat control switch. Depress the set button. Within 5 seconds, depress button 1.
• To program position 2, repeat the previous procedure using the set button and button 2.
• To recall position 1, depress button 1. To recall position 2, depress button 2.

A position can only be recalled when the transmission selector is in PARK or NEUTRAL. A position may be programmed at any time.
Easy Exit/Easy Entry
The easy exit function moves the seat backwards about 2 inches when the ignition key is removed from the ignition switch. The DSM receives a key out command over the SCP communication network and powers the driver seat rearward. This function will not operate if the seat is less than the travel distance to the end of the track, or the function has been deactivated at the message center driver personality settings. The DSM will also cancel this operation if a valid input command is received, such as the seat control switch or memory recall request.
The DSM will record the current seat position before powering the seat for an easy exit function. This recorded position will be used to return the seat to this position on the easy entry operation. During easy entry operation, the seat is returned to the position previous to the easy exit operation. Easy entry operation will be cancelled if a valid input command is received by the DSM.
Passenger Power Seat
The passenger power seat motors are hardwired to the passenger seat control switch. The circuits are normally at ground through the seat control switch. The individual circuit is switched to power when the specific adjustment position is selected.
-----------------------------------------------------------------------------------------------------------------------------
Visual Inspection Chart Mechanical Electrical

• Front seat track motors
• Front seat track binding or obstructed
• Front seat backrest power recline
• Lumbar motor
• Climate controlled seat ducts

• Driver door module fuse(s):
  • Central junction box (CJB) fuse 7 (5A)
  • CJB fuse 22 (10A)
• Driver seat module fuse(s):
  • Battery junction box (BJB) fuse 21 (20A)
  • CJB fuse 7 (5A)
• Passenger power seat BJB fuse 28 (20A)
• Rear heated seat fuse(s):
  • BJB 11 (20A)
  • CJB fuse 16 (5A)
• Driver power lumbar BJB fuse 21 (20A)
• Passenger power lumbar BJB fuse 28 (20A)
• Driver and passenger climate controlled seat module fuse(s):
  • BJB fuse 26 (30A)
  • CJB fuse 16 (5A)
• Seat control switch
• Memory set switch
• Lumbar seat control switch
• Seat fan motor
• Climate controlled seat module
• Climate controlled seat switch

Check for obstuction on seat track or try listening to see if you can hear seat motor operating. if you can't hear motor operating check fuse.

it sounds like the driver seat module. It controls all of these items.
buy used at car-part.com. look on page with * for lowest price.
buy new at discount at tascafordparts.com

• The memory mirror is inoperative

• Driver seat module (DSM).
• Circuitry.
• CJB fuse 3 (7.5A).
• Exterior mirror motor.
• Mirror control switch.

• The memory seat is inoperative

• Circuitry.
• Seat control switch.
• Seat track.
• DSM.
• PDJB Fuse 109 (30A).
• Power seat motor.

• Adjustable brake pedal does not operate correctly — does not operate using the adjustable pedal switch

• Battery junction box (BJB) fuses:
  • 109 (30A).
• Circuitry.
• Switch.
• Adjustable pedal motor.
• Driver Seat Module (DSM

I have the very same problem, no seat heat on either side and no power seat control on the drivers side. anyone know which fuse or switch operates the drivers side power seat? Thanks

If only one seat is not working the fuse/relay is ok or both would not work, most likely cause based on experience is the control switch, then the power seat motor.