Are there torque specs for the throttle body & the idle air control module?

What Colorado do you have ? 2 wheel or 4 wheel drive ? Sport ,sport LS 3.5L , Z71, Z71 LS. etc. what size engine ? an does it have electronic throttle control ? I have factory service info an it is not showing that code .
DTC P0506

Circuit Description

The throttle actuator control (TAC) motor is controlled by the powertrain control module (PCM). The DC motor located in the throttle body drives the throttle plate. In order to decrease idle speed, the PCM commands the throttle closed reducing air flow into the engine and the idle speed decreases. In order to increase idle speed, the PCM commands the throttle plate open allowing more air to pass the throttle plate. If the actual idle RPM does not match the desired idle RPM within a calibrated time, this DTC sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:
DTC P0506 Idle Speed Low
DTC P0507

Circuit Description

The throttle actuator control (TAC) motor is controlled by the powertrain control module (PCM). The DC motor located in the throttle body drives the throttle plate. In order to decrease idle speed, the PCM commands the throttle closed reducing air flow into the engine and the idle speed decreases. In order to increase idle speed, the PCM commands the throttle plate open allowing more air to pass the throttle plate. If the actual idle RPM does not match the desired idle RPM within a calibrated time, this DTC sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:
DTC P0507 Idle Speed High
Cleaning the throttle body mite take care of it !
Cleaning Cleaning An Electronic Throttle Body Safely

Extracted from Engine-Codes.com

Code P0507

Possible causes

- Dirty throttle body

- Electric throttle control actuator misadjusted or damaged

- Faulty Electric throttle control actuator

- Intake air leak

- Poor electrical connection to the Intake Air Control (IAC) valve


What does this mean?

Tech notes

If there are no intake leaks, clean throttle body, adjust engine idle and erase engine code. If the code comes back you may have to replaced the Electric Throttle Control Actuator (Motor) to repair the problem.



There is a factory service bulletin for the following Chevrolet models:



2006-2008 Chevrolet Trail Blazer

2007-2008 Chevrolet Avalanche

2007-2008 Chevrolet Express

2007-2008 Chevrolet Silverado

2007-2008 Chevrolet Suburban

2007-2008 Chevrolet Tahoe

Chevrolet Factory Service Bulletin OBDII Code P0507


What does this mean?

When is the code detected?

Thi P0507 code sets when the Powertrain Control Module (PCM) detects an engine speed outside of the Idle Air Control (IAC) valve range of control.

Possible symptoms

- Engine Light ON (or Service Engine Soon Warning Light)

- Engine hard to start

- Rough or erratic idle speed

P0507 Chevrolet Description

The Idle Air Control (IAC) valve is a Powertrain Control Module (PCM) controlled stepper motor located on the throttle body. The stepper motor drives a valve pintle which protrudes into a passage that bypasses the throttle plates. The PCM commands the IAC valve pintle to extend to decrease the idle speed. The bypass air flow is reduced and the idle speed decreases as the pintle approaches its seat. The PCM retracts the IAC valve pintle away from its seat to increase the idle speed. The retracting of the IAC valve pintle allows more air to bypass the throttle plates. One of the PCMs uses for the IAC system is to maintain a desired idle speed. This DTC sets when the PCM detects an engine speed outside of the IAC\'s range of control.





Read more: http://engine-codes.com/p0507_chevrolet.html#ixzz3ObdI2chF

It should be noted that the ETC system includes a warning indicator (wrench light) on the instrument cluster that illuminates when a fault is detected. Faults are accompanied by DTCs and may also illuminate the malfunction indicator lamp (MIL).
Torque Based Electronic Throttle Control (ETC)
Overview
The Generation II (Gen II) torque based electronic throttle control (ETC) is a hardware and software strategy that delivers an engine output torque (via throttle angle) based on driver demand (pedal position). It uses an electronic throttle body, the PCM, and an accelerator pedal assembly to control the throttle opening and engine torque. The ETC system replaces the standard cable operated accelerator pedal, idle air control (IAC) valve, 3-wire throttle position sensor (TPS), and mechanical throttle body.
Torque based ETC enables aggressive automatic transmission shift schedules (earlier upshifts and later downshifts). This is possible by adjusting the throttle angle to achieve the same wheel torque during shifts, and by calculating this desired torque, the system prevents engine lugging (low RPM and low manifold vacuum) while still delivering the performance and torque requested by the driver. It also enables many fuel economy/emission improvement technologies such as variable cam timing (VCT) (deliver same torque during transitions).
Torque based ETC also results in less intrusive vehicle and engine speed limiting, along with smoother traction control.
Other benefits of ETC are:

• Eliminate cruise control actuators.
• Eliminate idle air control (IAC) valve.
• Better airflow range.
• Packaging (no cable).
• More responsive powertrain at altitude and improved shift quality.
• DO you know what electronic throttle control is ?

014 Electronic Throttle Operation

If it dies when you are coming to a stop after being on the freeway, chances are the torque converter solenoid is sticking in the transmission.
If it is doing it around town, I would look at the throttle body and idle air control valve. The computer controls idle speed by regulating air flow into the throttle body.

The 3 wire Throttle Position Sensor (TPS) is mounted on the throttle body and is connected to the throttle blade.
The TPS is a 3wire variable resistor that provides the Powertrain Control Module (PCM) with an input signal (voltage) that represents the throttle blade position of the throttle body. The sensor is connected to the throttle blade shaft. As the position of the throttle blade changes, the resistance (output voltage) of the TPS changes.
The PCM supplies approximately 5 volts to the TPS. The TPS output voltage (input signal to the PCM) represents the throttle blade position. The PCM receives an input signal voltage from the TPS. This will vary in an approximate range of from .26 volts at minimum throttle opening (idle), to 4.49 volts at wide-open throttle. Along with inputs from other sensors, the PCM uses the TPS input to determine current engine operating conditions. In response to engine operating conditions, the PCM will adjust fuel injector pulse width and ignition timing.
The PCM needs to identify the actions and position of the throttle blade at all times. This information is needed to assist in performing the following calculations:

• Components & Systems
• • Auto Shut Down Relay
  • Camshaft Position Sensor
  • Components & Systems
  • Crankcase Ventilation System
  • Crankshaft Position Sensor
  • Evaporative Emission Control System
  • Heated Oxygen Sensor
  • Idle Air Control Motor
  • Intake Air Temperature Sensor
  • Intermittent Fault Tests
  • Knock Sensor
  • Manifold Absolute Pressure Sensor
  • Positive Crankcase Ventilation System
  • Throttle Position Sensor
  • Transmission Range Sensor Solenoid Assembly
  • Vehicle Speed Control

• HOME
• REPAIR INFO
• 2001 JEEP GRAND CHEROKEE 4WD 4.0L MFI 6CYL REPAIR GUIDE
• ENGINE PERFORMANCE & EMISSION CONTROLS
• COMPONENTS & SYSTEMS
• THROTTLE POSITION SENSOR

Cherokee, Grand Cherokee, 1999-2005
Throttle Position Sensor

• OPERATION
• REMOVAL & INSTALLATION

Print

Operation

The 3 wire Throttle Position Sensor (TPS) is mounted on the throttle body and is connected to the throttle blade.
The TPS is a 3wire variable resistor that provides the Powertrain Control Module (PCM) with an input signal (voltage) that represents the throttle blade position of the throttle body. The sensor is connected to the throttle blade shaft. As the position of the throttle blade changes, the resistance (output voltage) of the TPS changes.
The PCM supplies approximately 5 volts to the TPS. The TPS output voltage (input signal to the PCM) represents the throttle blade position. The PCM receives an input signal voltage from the TPS. This will vary in an approximate range of from .26 volts at minimum throttle opening (idle), to 4.49 volts at wide-open throttle. Along with inputs from other sensors, the PCM uses the TPS input to determine current engine operating conditions. In response to engine operating conditions, the PCM will adjust fuel injector pulse width and ignition timing.
The PCM needs to identify the actions and position of the throttle blade at all times. This information is needed to assist in performing the following calculations:


Ignition timing advance Fuel injection pulse-width Idle (learned value or minimum TPS) Off-idle (0.06 volt) Wide Open Throttle (WOT) open loop (2.608 volts above learned idle voltage) Deceleration fuel lean out Fuel cutoff during cranking at WOT (2.608 volts above learned idle voltage) A/C WOT cutoff (certain automatic transmissions only)

Removal & Installation

3.7L & 4.0L

1. Disconnect TPS electrical connector.
2. Remove TPS mounting screws.
3. Remove TPS.

To Install:
The TPS is mounted to the throttle body. The throttle shaft end of throttle body slides into a socket in the TPS. The TPS must be installed so that it can be rotated a few degrees. (If sensor will not rotate, install sensor with throttle shaft on other side of socket tangs). The TPS will be under slight tension when rotated.

1. Install TPS and retaining screws.
2. Tighten screws to 7 Nm (60 inch lbs.) torque.
3. Connect TPS electrical connector to TPS.
4. Manually operate throttle (by hand) to check for any TPS binding before starting engine.

4.7L

1. Remove air duct and air resonator box at throttle body.
2. Disconnect TPS electrical connector.
3. Remove two TPS mounting bolts (screws).
4. Remove TPS from throttle body.

To Install:
The throttle shaft end of throttle body slides into a socket in TPS. The TPS must be installed so that it can be rotated a few degrees. If sensor will not rotate, install sensor with throttle shaft on other side of socket tangs. The TPS will be under slight tension when rotated.

1. Install TPS and two retaining bolts.
2. Tighten bolts to 7 Nm (60 inch lbs.) torque.
3. Manually operate throttle control lever by hand to check for any binding of TPS.
4. Connect TPS electrical connector to TPS.
5. Install air duct/air box to throttle body.

Hope this helps

Idle Air Control Valve Pintle may be bad If you disconnect the IAC and the problem ceases it can point to this being the problem.: Removal & Installation 3.5L Engine To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Remove the fuel injector sight shield.
3. Drain the cooling system.
4. Remove or disconnect the following:
   • The air cleaner intake duct. Figure of IAC and TPS electrical connectors disconnected.
     
     
   • The idle air control (IAC) valve and throttle position (TP) sensor electrical connectors. Figure of cruise control and throttle control cables removed from throttle lever.
     
     
   • The cruise control cable and throttle control cable from the throttle body lever.
   • The fuel pressure regulator vacuum hose, positive crankcase ventilation (PCV) hose and the throttle body vacuum port hose.
   • The throttle body coolant hoses.
   • The throttle control cable bracket, leaving the throttle and cruise cables connected.
   • The upper nut holding the throttle body to the intake manifold.
   • The throttle body assembly.
5. Clean the gasket mating surfaces.

To Install:

1. Install a new gasket and new studs if necessary.
2. Install or connect the following:
   • The throttle body assembly.
   • Start the top nut by hand.
   • The throttle body coolant hoses.
   • Position the throttle control cable bracket and hand start the retaining nuts and bolt.
   • Torque the three throttle body retaining nuts to 89 in.lbs. (10 Nm). And the bracket retaining bolt to 115 in.lbs. (13 Nm).
   • The throttle body vacuum port hose, PCV valve hose and the fuel pressure regulator hose.
   • The throttle control and cruise control cables to the throttle body lever.
   • The IAC valve and TP sensor electrical connectors.
   • The air intake duct.
3. Refill the cooling system.
4. Install the fuel injector sight shield.

4.0L Engine To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Relieve the fuel system pressure.
3. Remove or disconnect the following:
   • Negative battery cable.
   • The Mass Air Flow (MAF) sensor electrical connector.
   • The air cleaner intake duct.
   • The PCV valve fresh air tube. Figure of cruise control cable removed from throttle cable bracket.
     
     
   • The cruise control cable and throttle control cable from the bracket.
   • The cruise control cable and throttle control cable from throttle body lever. Figure of IAC valve and TPS connectors removed.
     
     
   • The idle air control (IAC) valve and throttle position (TP) sensor electrical connectors. Figure of fuel lines removed from retainer on throttle cable bracket.
     
     
   • The fuel feed and return lines from the retainer on the throttle control cable bracket.
   • The transaxle shift cable clip from the throttle control cable bracket. Figure of throttle body removed from water crossover.
     
     
   • The throttle body from the water crossover.

To Install:
NOTE: The Mass Air Flow (MAF) sensor inlet and the outlet of the air cleaner assembly must line up when installed. Misalignment may cause MIL illumination or driveability concerns.

1. Install or connect the following.
   • The throttle body to the water crossover. Torque the bolts to 106 in.lbs. (12 Nm).
   • The IAC valve and TP sensor electrical connectors.
   • The throttle and cruise control cables to the throttle body lever.
   • The throttle and cruise control cables to the throttle control cable bracket. The transaxle shift cable clip to the throttle control cable bracket.
   • The fuel feed and return line retainer to the throttle control cable bracket.
   • The MAF sensor electrical connector.
   • The air cleaner intake duct clamp. Torque the clamp to 27 in.lbs. (3Nm).
   • The PCV valve fresh air tube.
   • The fuel injector sight shield. Torque the nuts to 20 in.lbs. (2.3 Nm).
2. Install the negative battery cable.
3. Pressurize the fuel system and verify no leaks.

3.0L and 3.5L V6

Torque Specifications

air intake plenum 11-14 ft lbs.

camshaft bearing cap 14-15 ft lbs.

connecting rod nut 37-38 ft lbs.

camshaft sprocket bolt 66-67 ft lbs.

crankshaft pulley bolt 108-116 ft lbs.

cylinder head bolts 65-72 ft lbs. ( 3.0L) 76-83 ft lbs. (3.5L)

drive plate ( flywheel ) 53-55 ft lbs.

exhust manifold 11-16 ft lbs.

intake manifold 11-15 ft lbs.

main bearing cap 55-61 ft lbs.

rocker shaft 14-15 ft lbs.

valve cover 27-35 in. lbs.

throttle body bolt 84-108 in. lbs.

Idle Air Control (IAC) Motor OPERATION The IAC motor is mounted to the throttle body and is operated by the engine controller. The throttle body has an air control passage that provides air for the engine at idle (when the throttle plate is closed). The IAC motor pintle protrudes into the air control passage and regulates air flow through it. Based on various sensor inputs, the engine controller adjusts engine idle speed by moving the IAC motor pintle in and out of the air control passage. The IAC motor is positioned when the ignition key is turned to the ON position.


OPERATION Found on V6, V8 and V10 engines, the intake manifold air temperature sensor is a variable, thermister type which reacts to temperature changes. In cold air, its resistance is high. As temperatures increase, its resistance decreases.






Fig. 2: Location of the intake manifold air temperature sensor — V8 engines


The sensor element itself extends into the intake manifold air stream to provide input voltage to the engine controller. This signal is used along with signals from other sensors by the engine controller to determine the fuel injector pulse width.

Idle air control at base of throttle body. Passages could be plugged or idle hard stop needs adjusting.

Air Intake System Sensors Air intake system sensors include a heated resistor-type mass air flow (MAF) sensor and throttle position (TP) sensor; both supply data to the powertrain control module (PCM). The PCM also monitors engine speed.
Air Intake System Control Devices The idle air control (IAC) solenoid regulates idle speed by adjusting the amount of air allowed into the intake manifold. Adjustment is made by varying the duty cycle output by the powertrain control module (PCM). The PCM will increase the duty cycle for added mechanical or electrical loads. The IAC solenoid is combined with the fast idle control (FIC) solenoid which is turned on when the air conditioner is engaged to help compensate for the additional load. The IAC valve must be replaced as an assembly with the FIC solenoid.
Fast Idle Control (FIC) Solenoid The fast idle control (FIC) solenoid (Figure 1) compensates for idle speed change caused by the operation of the air conditioner compressor. The FIC solenoid is controlled by the FIC relay. The FIC relay is energized when the air conditioner clutch is energized and the relay allows the FIC solenoid to turn on and let an additional volume of air into the intake manifold.
Figure 1: Fast Idle Control (FIC) Solenoid

------------------------------------------------------
Throttle Body (TB) The throttle body (TB) controls the amount of air that flows into the engine through a single butterfly valve. The single butterfly valve opening is determined by the accelerator pedal. The TB is cast with an air bypass channel and houses several emission-related components for the powertrain control module (PCM).
--------------------------------------------------------
Throttle Position Sensor (TP Sensor) The throttle position (TP) sensor responds to the accelerator pedal movement. The TP sensor is a potentiometer that transforms the throttle plate opening angle into output voltage and sends the voltage signal to the powertrain control module (PCM). In addition, the sensor detects the opening and closing speed of the throttle plate and sends the voltage signal to the PCM. Also, the TP sensor is used to determine the air intake when the mass air flow (MAF) sensor fails. This mode of operation is called Fail Safe.
The TP sensor integrates the idle (IDL) switch within the housing. The IDL switch detects when the throttle plate is closed and an idle condition occurs. The PCM is supplied with this input signal.

IDLE SPEED

the MAF sensor is between the air filter and throttle body. the idle controll is at the throttle body.  Its located on the throttle body on the left side. Follow the air intake to an intake manifold which sits on top of the throttle body.