Where is the windshield washer motor fuse located ?

Wiper/Washer System Components
The Wiper/Washer System consists of the following electrical components:
• Accessory relay
• Heated washer nozzles w/XA7
• WASH NOZ 10A fuse
• Windshield washer fluid level switch
• Windshield washer pump motor
• Windshield wiper motor
• Windshield wiper motor module
• Windshield wiper/washer switch
• Wiper/washer switch 10A fuse
• Wiper motor 30A fuse

Wiper/Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls wiper motor operation. The accessory voltage supply circuit to the windshield wiper motor assembly is used to operate the wiper motor in all modes. The windshield wiper motor is a 2 speed motor and is operated at low speed in all modes except HIGH. The accessory voltage supply circuit to the windshield wiper/washer switch is used to supply the windshield wiper switch signal circuits. The windshield wiper switch signal circuit voltage levels to the wiper motor module determine the wiper motor operating mode.
When the wiper/washer switch is in the LOW position voltage is supplied through a 24K ohm resistor within the switch to the windshield wiper switch signal 2 circuit, and accessory voltage is supplied to the windshield wiper switch signal 1 circuit. The reduced voltage from the wiper switch signal 2 circuit and accessory voltage from the wiper switch signal 1 circuit causes the wiper motor module to close the wiper motor accessory voltage supply circuit to the wiper motor low speed terminal.

Do you know what a wiring diagram is ? A wiring diagram for your vehicles windshield wipers electrical circuit would show all components involved . You would need a wiring diagram for testing ,so you know which wires too test . It would show the fuse location - amperage etc.... Which of these is your vehicle - Notchback or hatchback or station wagon .

xTooltipElement
Service Information
2008 Holden Viva ' Optra, Viva (VIN J) Service Manual ' Body Systems ' Wipers and Washers ' Schematic and Routing Diagrams ' Document ID: 1964803
--------------------------------------------------------------------------------
Wiper/Washer Schematics
Figure 1: Wiper System - Notchback
Figure 2: Wiper System hatchback and Station Wagon
Figure 3: Wiper System Hatchback and Station Wagon w/Intermittent
Figure 4: Wiper System Notchback w/Rain Sensor
Figure 5: Wiper System Hatchback and Station Wagon w/Rain Sensor
Figure 6: Wiper System Hatchback and Station Wagon w/Intermittent and Rain Sensor
© 2019 General Motors Corporation. All rights reserved.

The fuse would be marked WPR fuse # 9 25 amp. located in the IP fuse panel . IP - instrument panel fuse box . It's location is
Fuse Block - I/P
Behind the left side of the I/P access panel
Windshield Wiper System
The windshield wiper system consists of a wiper motor, a linkage, a wiper arm and a blade, and a wiper/washer switch. The windshield wiper circuit incorporates a self parking device which consists of a worm gear and a cam plate in order to keep the circuit engaged temporarily when the switch is turned off. The wiper system is driven by a permanent magnet-type motor. The windshield wiper motor is mounted on the dash panel and is directly connected to the windshield wiper linkage.
The windshield wiper motor has 2 speeds, LO and HI, and also has intermittent wiper capability. The wiper switch is an integral part of the wiper/washer switch. Windshield wiper operation is actuated through the lever on the right side of the steering column.

https://www.youtube.com/watch?v=MvXX3Xg3siM

Just replacing parts isn't the way to fix this problem , viewing wiring diagrams too see what all is involved in making the wipers work is . Then using a digital volt ohmmeter to test electrical circuits . Also looking at factory service info. to see how it's suppose to work.
Free wiring diagrams here http://www.bbbind.com/free-tsb/ Enter vehicle info. year , make , model an engine size . Under system click on body & accessories , then under subsystem click on wiper/washer . Click the search button ,then click the blue link. Looking at the wiring diagram i see two fuse's an two relays that are controlled by the BCM - body control module . Also hooking up a scan tool that can read BCM DTC'S - diagnostic trouble codes could be helpful . The wiper switch is a input to the BCM - the BCM will energize the relays to turn on the wipers.

Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper 1 relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIPER/SW 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper 1 relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay contacts to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
DTC B3715 05: Front Wiper Relay Drive Circuit Short to Battery or Open

Hard to say what's wrong without testing thing's . Is there B+ voltage to the wiper switch ? B + voltage to the wiper motor ? Do you know how to use a voltmeter ? How to test electrical circuits ?
Here is a factory service manual list of componets involved .
Wiper/Washer System Components
The Wiper/Washer System consists of the following electrical components:
• Accessory relay
• Heated washer nozzles w/XA7
• WASH NOZ 10A fuse
• Windshield washer fluid level switch
• Windshield washer pump motor
• Windshield wiper motor
• Windshield wiper motor module
• Windshield wiper/washer switch
• Wiper/washer switch 10A fuse
• Wiper motor 30A fuse

Do you know how the wipers work ?
Windshield Wiper Motor Wiring Tutorial
Wipers Inoperative - All Modes ?????
Wiper Motor Switch Troubleshooting

WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

Look for the fuse box under the dashboard, and look at the diagram on the cover for the proper location of the fuse, and use a plier (if you dont have fuse puller (small plastic one)), and gentle hold the fuse and pull it out carefully.

Hello and Welcome to Fixya
The fuse is in the engine compartment fuse box. See diagram in the owners manual section 6-11..to find out which one it is, or read the list (provided with amp labeling) on the inside cover to review the fuses there.
Locate the windshield washer fuse accordingly and replace it with the same labeled new fuse.

Do RATE my solution, If this helps you out.
Regards.

Check power at the pump motors. You may not see a fuse because some run off a circuit breaker. If all else fails, a bit "backyard" but you likely could break out the washer pumps from the system and make a simple push button on the dash to operate them.

The windshield washer pump is part of the windshield wash reservior.
There is an electrical connector located on the bottom of the reservior.
That is the pump .
If the pump is not in the reservior. I would just trace the washer fluid lines from the sprayer on the vehicle back to the pump. The lines just might lead back to the reservior for the windshield wash solution. Then you will have confirmed the pump is in the reservior.

You may have to get a new reservior. The pump might not be seperate item, I am not 100% sure on that.

I also would double check the fuses and any relays related to the washer pump.

Finally, I would check the washer switch if you replace the pump and still is not working .

Good luck

These days, most windshield washer pumps are mounted to the bottom of the washer fluid reservoir. Where’s that, you ask? Well, you know that spout you pour the fluid into—the one that disappears into nowhere? Well, the reservoir is actually located inside the front fender between the bumper and the front wheel. To replace the pump, you will have to jack up the vehicle, remove the front wheel and then remove the inner fender liner.