Headlights won't come on. HVAC and Instrument

Need to know make, model an year vehicle to answer that .

Have you made sure that the dimmer is not turned all of the way down?

The headlamp dimmer swich is in the column with the turn signal switch. If you are looking for the dash light or interior lighting dimmer switch, its attached to the instrument panel.

I’m happy to assist further over the phone at https://www.6ya.com/expert/kim_3202917d7c587455

look for a illum fuse not dimmer. im sure it is a blown fuse or the switch is broken. the dimmer can go.

No. Dash lights being out could be a bad headlight switch, since the dash lights are routed through the headlight switch, not the dimmer switch. Park and tail lights also controlled by the headlight switch.

needs headlight switch

You have to remove the panel to check onthe connections behind it, also check the headlights switch, they tend to burn out.

Have u tested the dimmer switch for the instrument panel lites? it is near the hd lite switch, they are a common cause of the problem, very common, also have found that allot of folks don't know there dimmer is trurned off.

Ye, the dimmer switch still works.

I know this because, when I turn on the left direction flasher, the panel lights pulse dimly on and off with the direction light flasher.

Do I have a defective direction light flasher? if so where is it located?

Are all of these not working ?
• Air temperature switch
• Cigar lighter lamp
• Door switches
• Driver information center (DIC) switch
• Headlamp switch
• Head-up display (HUD) switch
• Heated seat switches
• HVAC control assembly
• Instrument panel cluster (IPC)
• Memory function switch
• Radio
• Steering wheel controls
• Window switches

Interior Lamps Dimming
This group of interior lighting includes lamps which may be dimmed. This group uses a combination of class 2 controlled illumination and incandescent lamps:
• Air temperature switch
• Cigar lighter lamp
• Door switches
• Driver information center (DIC) switch
• Headlamp switch
• Head-up display (HUD) switch
• Heated seat switches
• HVAC control assembly
• Instrument panel cluster (IPC)
• Memory function switch
• Radio
• Steering wheel controls
• Window switches
For the interior lighting to be dimmed the following conditions must be met:

Here is a discription of how they work ,factory service info.
• A low light level has been detected by the dash integration module (DIM)
• Headlamp switch is placed in to the PARK or HEAD position
• Ignition switch is placed in the ON position
Then all class 2 displays and all incandescent back lighting will be illuminated to the level set by the instrument panel (I/P) dimmer switch. When the I/P dimmer switch is moved from MIN to MAX, all class 2 displays and all incandescent back lighting respond from minimum intensity to maximum brightness.
The DIM supplies battery positive voltage to the coil side of the PRK LP relay in the rear fuse block.
When the I/P dimmer switch is moved from MIN to MAX, then the instrument panel module (IPM), W/CJ2, or climate control panel (CCP), W/C67, applies a message to the class 2 communication circuit to the DIM. The DIM then applies a ground to the park lamp relay control circuit. This energizes the PRK LAMP relay and allows battery positive voltage to be applied through the DIMR fuse to the DIM. The DIM then illuminates the following incandescent lamps through the incandescent dimming output circuit:
• Cigar lighter lamp
• DIC Switch
• Headlamp switch
• HUD switch
• HVAC control assembly
• IPC
• Radio
• Steering wheel controls
The DIM also applies a message to the following class 2 controlled illumination components:
• Drivers door module (DDM)
• HVAC control assembly
• IPC
• Radio
The DDM will then send a message through the simple bus interface (SBI) to the RH front door module (RFDM). The door modules will then illuminate the following components through the incandescent dimming output circuit:
• Air temperature switch
• Heated seat switches (W/KA1)
• Memory function switch (W/A45)
• Power door lock switches
• Power window switches
The ground for these components are provided from the DDM and RFDM.
The following components are grounded at G200:
• Headlamp switch
• HVAC control assembly
• Radio
• Steering wheel controls
The following components are grounded at G201:
• Cigar lighter lamp
• DIC Switch
• HUD switch

Having the vehicle checked for DTC'S - diagnostic trouble code's would probably be your best course of action .
DTC B2556 (1)
The I/P dimmer switch is a potentiometer. The instrument panel module (IPM) determines the control setting based on the voltage from the I/P dimmer switch. The IPM sends out a class 2 message to the dash integration module (DIM). The intensity of the interior backlighting shall be adjustable when ever the park lamps are on. The intensity of the vacuum florescent displays shall only be adjustable when it is night and the park lamps are active.
DTC B2627
DTC B2628
Circuit Description
The I/P dimmer switch is a potentiometer. It is powered by the HVAC control module. The HVAC control module determines the level of dimming desired based on the voltage from the I/P dimmer switch. The HVAC control module converts the I/P dimmer switch feed back voltage to a digital signal and puts it on the Class II communication bus.

Dash Integration Module (DIM)
The DIM is wired to the class 2 serial data line. The various DIM input and output circuits are described in the corresponding functional areas as indicated on the DIM electrical schematics.
The DIM functions include the following:
• Control of headlights and exterior lamps
• Horn relay control
• Interior lamps incandescent dimming
• Lamps On signal with wiper/washer
• Power moding control over Class 2 serial data line
• Steering wheel controls
• Storage of the clock settings and, sending a message out on the class 2 serial data circuit in response to requests from other modules

Your best bet ,take your vehicle to a qualified repair shop.