SOURCE: saab turbo 9-3 need computer trouble code
P1300 is random misfiring. I suggest replacing your DI cassette with a known good unit or a replacement unit. Give more info on your vehicle. Any symptoms or running rough?
Justin
Strictly Saab
Melbourne, FL
SOURCE: remove rear wiper blade on saab 9-5 estate
Best way go to a parts store and ask for help and they would probably slip it on for you
God Bless you Greg
SOURCE: I need instructions for replacing the turbo on a Saab 1999 9-5 4 cyl turbo
Hi, I have done this and it is not too bad, but will take you about 4 hours if you are good, and longer if you have not done much mechanics.
The trick is to find a reasonably priced turbo, check ebay. There is a dude on there that just does rebuilt turbos. Very good, got mine for $
I have been reading up on turbo replacement procedure and I have found
this list: First, there are a couple of questions that I have about the
list:
2 air openings, pretty easy to figure out
2 exhaust openings, pretty easy to figure out
3 round openings in the center, all banjo bolts?
1 round / two bolt opening in the center.
1 Hose fitting off of the waste-gate
1 Hose fitting off of the air side of the turbo.
STEP 1 Open the expansion tank cap to release the system pressure.
STEP 2 Raise the car & Remove the lower front cover under the car
STEP 3 Drain off the coolant & Remove the turbo brackets
STEP 4 Loosen the return fitting and the pipe from the turbo to the block
STEP 5 Loosen the oil pipe between the filter adapter and the turbo
STEP 6 Lower the car to the floor & Remove the bypass valve & Unplug the connector from the control valve
STEP 7 Disconnect the mass air flow sensor connector & Loosen the hoses to the turbo
STEP 8 Remove the crankcase banjo bolt from the intake manifold and unscrew the bolt from the cam cover
STEP 9 Move the pipe and wiring aside & Remove the engine lifting eye
STEP 10 Remove the mass air flow sensor and air hose
STEP 11 Remove the exhaust manifold heat shield by removing the nut and two clips from underneath
STEP 12 Undo the intake manifold clamp at the turbo & remove the intake
STEP 13 Disconnect the hose clip on the hose between the intercooler
& turbo & plug it to keep something from falling in it
STEP 14 Loosen the front exhaust system from the turbo & lower the
front exhaust system away from the turbo (DO NOT BEND -THE FLEX HOSE)
STEP 15 Remove the oil pipe from the oil filter adapter & grab the copper washers
STEP 16 Loosen the coolant pipe by the turbo & grab the copper washers & loosen the coolant pipe bolt
STEP 17 Remove the coolant return pipe from the cylinder head & pressure sensor bracket. Once again, Grab the copper washers
STEP 18 Undo the coolant return pipe bolt by the turbo
STEP 19 Undo the nuts securing the turbo to the exhaust manifold. (spray the nuts with WD40)
STEP 20 Install in Reverse
Just did this for the first time. Here are a few hints that may help others.
1) PB BLASTER is your friend. Remove the exhaust top front heat shield and hit exhaust nuts with PB Blaster as soon as you start the job, or night before.
2) Make sure that you have 12mm closed end wrench with AND without
ratchet. Also a 1/2 size 12mm socket if you can find / make. These will
help.
3) You don't have to remove the oil filter, but there one bolt that it would be nice for. I did not and did manage to get the job done.
4) Take you time. More of finding the right tool combination for each bolt.
5) Two banjo bolts on the turbo were really on there. Needed to use a mini-acetylene torch to eat up.
6) Have extracting sockets and bits ready just in case there are issues getting bolts / nuts off.
Turbo had quite a bit of end-play, but spun fine. Classic symptoms,
blue smoke at start up and from time to time when driving. It was also
making a bit of noise at idle.
jeffo2 ort11
Also, should get new copper washers. I did not have I have some micro leaks from time to time but nothing bad.
SOURCE: fault with saab 9-3 aero
Hello I have a saab 9.3 SS 04 and had the same problem.
- intermittent wipe doesn't work, at all
- windscreen washers don't work, at all
- "normal" continuous, and fast wipe work, but the wipers
freeze in the middle of the windscreen if you let go of the
control stalk, rather than sweeping back to the resting position
- same "freeze" happens with the manual wipe (push down on the control stalk)
The weird thing is that, this morning, for about 10 minutes, it seemed to fix itself,
partially - the washers started working etc - but the intermittent
wipe still didn't work. However not long after that it went back to the
symptoms described above.
also if I unplugged my car battery for a minute the washers worked for several seconds but again same problem occurs.
Solution is to replace your wiper motor. its that "simple"
worked for me. The wiper motor has a lot of electronic stuff and seems to control the washer engine.
Good luck.
SOURCE: My Saab 9-3 turbo wastegate seems to be stuck
I think the actual problem may be generic to Saabs of the same age. So maybe this information will help many others
Yes the turbo was faulty but no it was simple to fix and did not cost me a lot.
the wastegate ( a valve which is opened to switch on the turbo) is driven by a vacuum actuator - and the actuator leaver arm which connects to the wastegate to the actuator had fallen off.
So The wastegate valve was stuck semi open up and never moved.
This does not directly show any engine error or cause any emissions
problems, as the car passed an a mot before immediately before the fault was found.
My local garage man did the work needed in 2.5 hours on the ramp and did not have to take much too bits to make a good repair.
Car goes like a train, and the engine management light - which was coming on at odd times has since stayed off.
I suspect that the management light which was coming on due to emissions sensors -- triggered by some series of events which cause the emmision to go out out of line, due to the turbo not fully working.
257 views
Usually answered in minutes!
×