I have a Crime stoppers, remote starter. Original key fob will not unlock or lock the doors. Only remote starter to lock and unlock doors, having to carry both is very cumbersome. HELP

go to any Toyota dealer. They will sell you a new key fob but they also charge extra for programming. Total cost for the key fob and programming will be around $100. any Toyota dealer can do it for you

in what way do you mean. is the remotes not working or are they another set? original set you turn key in ignition to number 2 and press the fob. (remote) then the doors should lock press again to unlock and turn key back to 0 and try fob again do this for both. make sure the batteries are new in the fob's. leave ignition off for 3 min before doing the other one.

missing chip? empty battery in FOB? lost coding? blown fuse for remote starter circuit?

1 - Unlock the doors. Put the key in the ignition, and turn from "Off" to "ACC" 8 (eight) times in under 10 seconds. The doors will lock. Leave key in the "ON" position

2 - Program the fobs by pressing any key on the fob. The doors locks will lock/unlock

3 -- Turn the key to Off. Locks will lock/unlock, and you are out of programming mode.

I bought new remote Key Fob on Ebay and it did work properly on my Ford Transit LWB 2003. Good Luck!

reprogram the remote transmitter. first leave driver door open all other doors closed,key removed from the ignition switch. insert key into the ignition switch,then remove it.press lock and unlock on the vechicle door lock control switch at 1 second intervals 5 times. close and repoen drivers door.press lock and unlock on the vechicle lock control switch at 1 second intervals 5 times. insert key into ignition switch. switch ignition on and off twice to program a remote transmitter code whilst erasing the original codes or three timre to check how many remote transmitters are currently registered.remove key from the ignition switch.system should now lock and unlock.twice to indicate programming mode or one to four times,slowly to indicate number of remote transmitters registered.for the solara press and hold lock and unlock remote buttons together, press lock remote button for a second period of 1 second. system should now lock and unlock vechicle.once to confirm, twice to indicate registration has failed.if required repeat button procedure to program remaining remote transmitters.note to exit programming mode close drivers door or insert ignition key.maximum of 4 remote transmitters can be programmed.if akk failed let dealership reprogram remote transmitters.

1. Close and lock all doors with the driver’s side power lock/unlock switch.

2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard
Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder
each time. If this procedure is performed too fast, system will not enter programming mode.

3. Insert key into the ignition cylinder and turn to the ACC position.

4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press
the button more than one time in the above step. If the button is pressed more than one time, the programming
procedure will not be successful.

5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver’s side
power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should
flash. Repeat this step for each transmitter (including any existing transmitters).
6. Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door.

1) remote starter was not hooked up to the factory arm wire
2) trunk release was programmed to disarm factory alarm before popping trunk
3)parking light wire on remote starter was not hooked up
4)disarm wire from remote starter was not hooded up
5)this is not normal and they should fix the problem or have it done by some one else and have them pay for it, how much did they charge,
Bring it over I'll fix it right and not charge overpriced amount

i think that this is to prevent you from locking your keys in the car with the engine running.
Some remote starters have a feature that when the car is running (and in park) you can hit the remote start button twice for one second each - then you can take the key out of the ignition and still have the car running.
At this point....if you would hit the 'lock' button on your door the doors would immediately unlock. However, if you get out of the car and close the door leaving it unlocked and then you hit the 'lock' on your original car remote the doors will lock and stay locked. So now the car is running the doors are locked and you have the keys in your hands. Then you can run into the store or house real quick with your car locked.
Once you come back, you hit 'unlock' on the original car remote. the doors will unlock - you can get it - and then before hitting the brake put the key in the ignition and turn it (dont crank it) as if you had when originally using the remote starter.
Maybe this will work for you.....

To program a remote... note that you must not delay more than 10 seconds between any of the operations.

Driver's door open, all other doors closed, key removed from the ignition switch.

Insert key into ignitions switch, then remove it.

Press LOCK then UNLOCK on the vehicle door lock control switch at 1 second intervals 5 times.

close and re-open drivers door.

Press LOCK and UNLOCK on the vehicle door lock control switch at 1 second intervals 5 times

Insert Key into ignition switch.

Switch ignition ON and OFF once to program a remote transmitter code while retaining the original codes or twice to program a remote transmitter code while erasing the original codes. three times to check how many remote transmitters are currently registered, or 5 times to erase all registered codes.

Remove Key from ignition switch.

System should now lock and unlock vehicle. Once, twice or five times depending which mode has been selected. It will lock and unlock one to four times slowly, to indicate the number of remote transmitters registered if you chose option 3.

Press and hold remote transmitter LOCK and UNLOCK buttons at the same time.

Press LOCK remote button for 1 second: System should now lock and unlock vehicle once to confirm, twice to indicate registration has failed.

NOTE: to exit programming mode, close drivers door or insert key in the ignition.

NOTE: a maximum of 4 remote transmitters can be programmed