Liftgate ajar on at all time and liftgate is not open remotely nor from the control button.

more then likely it's a door ajar switch - not a sensor .
Anti-Theft- Perimeter Alarm System
The perimeter anti-theft system provides for vehicle security through an audible and visual notification if the vehicle's exterior is invaded without the system being shut off. The system self-arms when the doors, liftgate and hood are closed and the key is OFF. Any open door, hood or liftgate will prevent the system from arming. The hood ajar switch, door ajar switches and liftgate ajar switch cause these circuits to register as normally closed circuits. The vehicle security module monitors the status of the hood ajar, door ajar and liftgate ajar switches. If these circuits indicate an open entry point, the switch opens the circuit to the vehicle security module, which energizes the horn and autolamp relays (causing the horn to sound and the lights to flash). The vehicle security module turns off the anti-theft system when it receives a command through the keyless entry keypad, remote keyless entry (RKE) transmitter, or anti-theft alarm inhibit switch.
https://www.youtube.com/watch?v=egIGBzO065U

Does it have a power lift gate ? Do you know anything about automotive electrical systems ? How to use a wiring diagram along with a digital volt ohmmeter to test electrical circuits . ?
Power Liftgate
The power liftgate feature will allow the customer to automatically open or close the liftgate by activating the interior open/close switch, the remote keyless entry transmitter, or by manually initiating liftgate movement. The power liftgate uses a power cinch system to latch the liftgate.
The power liftgate system consists of:

• Power liftgate control switch (located in the overhead console)
• Power liftgate motors (located in the rear headliner area)
• Optical sensor and power liftgate encoder wheel (located in the left power liftgate motor assembly)
• Pinch strip switches (located on the body by the liftgate)
• Home position switch (located on the cinch actuator)
• Forkbolt switch (located on the cinching latch assembly)
• Detent switch (located on the cinching latch assembly)
• Liftgate close chime module (located in a unit external from the power liftgate module)

The forkbolt and detent switch are located on the cinch latch assembly and the home position switch is located on the cinch actuator assembly. For information on removal of the latch or cinch actuator assembly, refer to Section 501-14 .
The power liftgate may not operate under the following conditions:

• a low voltage or dead battery.
• a disconnected battery.
• a power liftgate that has been left open for more than six hours.
• a power liftgate that has been manually closed and left ajar.

If any of these conditions has occurred, the power liftgate must be reset before performing any pinpoint tests. For additional information, refer to Power Liftgate Initialization .

Power Liftgate Initialization NOTE: If the power liftgate system is turned OFF in the message center, the system cannot be activated with any switches or with the liftgate handle. The system will need to be turned ON for any power operation to occur.
NOTE: The power liftgate may not operate under the following conditions:

• a low voltage or dead battery.
• a disconnected battery
• a power liftgate that has been left open for more than six hours.
• a power liftgate that has been manually closed and left ajar.

If any of these conditions has occurred, the power liftgate must be reset.

1. Manually close and fully latch the power liftgate.

1. NOTE: If the power liftgate does not open during this step, refer to the symptom chart to diagnose the power liftgate for no operation. Power open the power liftgate by using the keyfob or overhead console switch.

1. Once the power liftgate is fully open, close the power liftgate by using the keyfob or overhead console switch.
2. your best bet mite be to have a qualified repair shop check it out .

Door ajar switch possibly . The lift gate not working is a different matter . Could be any number of thing's .
Power Liftgate System Components
• Liftgate motor assembly
• Liftgate latch
• Liftgate module (LGM)
• Liftgate side upper sensor - left
• Liftgate side upper sensor - right
• Liftgate handle switch
• Liftgate close switch
• GMLAN serial data link
• PWR LIFT GATE 30 amp fuse
• PLG 10 amp mini-fuse

Your best bet take it to a qualified repair shop that has the diagnostic tool that can communicate with the lift gate control module , too check for DTC'S - diagnostic trouble code's .
Liftgate Module
The liftgate module controls the liftgate motor, liftgate clutch, and liftgate latch based on various inputs. The liftgate module also performs diagnostics on these inputs and outputs and will disable liftgate functionality and set DTCs should a fault be detected. The liftgate module is secured to the motor assembly at the left rear of the vehicle. The module requires a liftgate position learn procedure be performed when replacing. This allows the module to learn the full open and full closed positions of the liftgate.

DTC B153A 00: Liftgate Latch Switch Signal Circuit
DTC B153A 08: Liftgate Latch Switch Signal Circuit Signal Invalid
DTC B153B 02: Liftgate Open Switch Signal Circuit Short to Ground
DTC B153B 05: Liftgate Open Switch Signal Circuit Open
DTC B153E 02: Liftgate Position Sensor Signal Circuit Short to Ground
DTC B153E 05: Liftgate Position Sensor Signal Circuit Short to Battery or Open
DTC B153E 08: Liftgate Position Sensor Signal Circuit Signal Invalid

This is not a job for a diy'er or vehicle owner .

Power Liftgate
The power liftgate feature will allow the customer to automatically OPEN or CLOSE the liftgate by activating the interior open/close switch, the remote keyless entry transmitter or by manually initiating liftgate movement. The power liftgate uses a power cinch system to latch the liftgate.
The power liftgate system consists of the following:

• Power liftgate control switch (located in the overhead console)
• Power liftgate motors (located in the rear headliner area)
• Optical sensor and power liftgate encoder wheel (located in the left power liftgate motor assembly)
• Pinch strip switches (located on the body by the liftgate)
• Home position switch (located on the cinch actuator)
• Forkbolt switch (located on the cinching latch assembly)
• Detent switch (located on the cinching latch assembly)
• Liftgate close chime module (located in a unit external from the power liftgate module)
• There are a lot of electrical switches an motors
• Visual Inspection Chart Mechanical Electrical
  • Power liftgate motors
  • Power cinching latch and linkage
  • Power liftgate pinch strip switches
  • Liftgate and liftgate hinges
  • Liftgate assist cylinders
  • Liftgate strikers
  • Exterior release handle and linkage
  • Liftgate weatherstrip
  • Liftgate alignment to body and striker
  • Central junction box (CJB) fuse:
    • 5 (7.5A)
    • 105 (30A)
  • Power liftgate control switch
  • Wiring harness
  • Connectors
  Are you willing to take the back hatch apart to test this ,to find a fix . But first have it check for DTC'S - diagnostic troulbe codes '
• Power Liftgate Module Diagnostic Trouble Code (DTC) Index
  Power Liftgate Module Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1342 ECU Is Defective Power Liftgate Module INSTALL a new power liftgate module. REFER to Power Liftgate Module in this section. B2477 Module Configuration Failure Power Liftgate Module REFER to Section 418-01 . B2522 Vbatt1 Circuit Failure Power Liftgate Module Go To Pinpoint Test B . B2552 Vbatt2 Circuit Open Power Liftgate Module Go To Pinpoint Test B . B2698 Vbatt2 Circuit Failure Power Liftgate Module Go To Pinpoint Test B . B2699 Left Pinch Strip Open or Short to Battery Power Liftgate Module Go To Pinpoint Test B . B2700 Right Pinch Strip Open or Short to Battery Power Liftgate Module Go To Pinpoint Test B . B2701 Left Pinch Strip Stuck Active Power Liftgate Module Go To Pinpoint Test B . B2702 Right Pinch Strip Stuck Active Power Liftgate Module Go To Pinpoint Test B . B2703 Open/Close Switch Stuck Active Power Liftgate Module Go To Pinpoint Test B . B2704 Optical Sensor Power Short to Ground Power Liftgate Module Go To Pinpoint Test B . B2705 Optical Sensor 1 Input Not Active During Powered Gate Movement Power Liftgate Module Go To Pinpoint Test B . B2706 Optical Sensor 2 Input Not Active During Powered Gate Movement Power Liftgate Module Go To Pinpoint Test B . B2709 Gate Open Output Short to Battery Power Liftgate Module Go To Pinpoint Test B . B2710 Gate Close Output Short to Battery Power Liftgate Module Go To Pinpoint Test B . B2711 Gate Open Output Short to Ground or Open Power Liftgate Module Go To Pinpoint Test B . B2712 Gate Close Output Short to Ground or Open Power Liftgate Module Go To Pinpoint Test B . B2713 Unlatch Output Short to Ground or Open Power Liftgate Module Go To Pinpoint Test B . B2714 Uncinch Output Short to Ground or Open Power Liftgate Module Go To Pinpoint Test B . B2715 Cinch Output Short to Ground or Open Power Liftgate Module Go To Pinpoint Test B . B2718 Gate Ajar Output Short to Battery Power Liftgate Module Go To Pinpoint Test B . B2721 Gate Ajar Output Short to Ground or Open Power Liftgate Module Go To Pinpoint Test B . B2722 Open/Close Switch Active During Self-Test Power Liftgate Module Go To Pinpoint Test B . B2723 Glass Position Switch Active During Self-Test Power Liftgate Module Go To Pinpoint Test B . B2724 Forkbolt Switch Invalid During Self-Test Power Liftgate Module Go To Pinpoint Test B . B2725 Detent Switch Invalid During Self-Test Power Liftgate Module Go To Pinpoint Test B . B2726 Home Switch Invalid During Self-Test Power Liftgate Module Go To Pinpoint Test B . B2819 Gate Motor Circuit Short to Battery Power Liftgate Module Go To Pinpoint Test B . B2820 Gate Motor Circuit Short to Ground or Open Power Liftgate Module Go To Pinpoint Test B . B2821 Cincher Motor/Unlatch Actuator Short to Ground or Open Power Liftgate Module Go To Pinpoint Test B . B2822 Cincher Motor/Unlatch Actuator Short to Battery Power Liftgate Module Go To Pinpoint Test B . B2825 Movement Ceased Due to Excess Speed Deviation Power Liftgate Module Go To Pinpoint Test B . B2903 Chime Output Circuit Short to Battery Power Liftgate Module/ Liftgate Chime Module Go To Pinpoint Test C . C1935 Chime Circuit Failure Power Liftgate Module/ Liftgate Chime Module Go To Pinpoint Test C . U1950 UBP Communication BUS Fault UBP Communi- cation REFER to Section 418-00 . U2338 Invalid ACM Message Data Power Liftgate Module REFER to Section 418-00 . U2242 Invalid 4WAS Message Data 4WAS Module REFER to Section 308-07A . U2403 Invalid CSM Message Data Vehicle Security Module REFER to Section 418-00 . U2406 Invalid IC Message Data Instrument Cluster Module REFER to Section 413-01 . U2469 Power Liftgate Disabled By Customer Interface Instrument Cluster Module Turn power liftgate on at message center. U2470 Unexpected Keyfob/Keypad Button Press Power Liftgate Module Go To Pinpoint Test A . U2471 Unexpected PRNDL State Power Liftgate Module REFER to Section 419-10 . U2472 Unexpected IGN State Power Liftgate Module REFER to Section 418-00 . U2473 Unexpected Vehicle Speed Instrument Cluster Module/ Powertrain Control Module REFER to Section 413-01 . U2528 PRNDL Data Mismatch Power Liftgate Module/ Instrument Cluster Module Go To Pinpoint Test D .

An electronic control module controls it .
The liftgate module (LGM) controls operation of the liftgate latch motor and the liftgate actuator assembly. Do you have a Liftgate Ajar Indicator ON ? Or a message in the message center driver information center (DIC) illuminates the LIFT GATE AJAR indicator ? The liftgate control module could have a DTC - diagnostic trouble code in memory !

When open, the liftgate can be closed by either a keyless entry transmitter or the liftgate close switch. When a GMLAN serial data message or switch input is seen, the liftgate module begins the close sequence. The liftgate motor is reversed, lowering the liftgate until it latches into the liftgate latch. Once latched, the latch will cinch the liftgate to a fully closed position.
Power liftgate function will only be allowed if certain operating criteria are met. Any of the following may cause the power liftgate not to function:
?€¢ Vehicle is not in park. ?€¢ Engine cranking is present. ?€¢ Temperature limits have been exceeded. ?€¢ Liftgate motor overcurrent is detected. ?€¢ Excessive hall effect counts are seen. ?€¢ System voltage is out of range. ?€¢ A DTC is set that disables power liftgate functionality. The liftgate also receives inputs from 2 object detection sensors. If either of these sensors indicate an object is in the path of the liftgate, liftgate functions will be suspended until the object is removed.

replace your remote battery or some wire is making a bad touch or disconnected

I recently had a similar problem with the "liftgate ajar" light lighting randomly on my 2001 PT Cruiser. It was even occurring AFTER I had disconnected the "ajar sensor" on the liftgate. Finally found that 5 wires were broken, one of them the liftgate ajar sensor wire, in the wire bundle that leaves the top of the liftgate and goes into the chassis. I suspect that those broken wires would randomly trigger. Inline spliced the wires and resealed the bundle. Everything looks good for now, although time will tell.

how to i open a stuck lift garte on a ford winstar 2000 lock broken too

The liftgate consists of the following components:

• liftgate door lock actuator
• liftgate lock cylinder (if equipped)
• liftgate window glass
• liftgate window latch/ajar switch
• liftgate window glass release handle
• liftgate latch remote control which consists of the following component:
  • liftgate release handle
• liftgate latch, which consist of the following component:
  • liftgate latch door ajar switch

Liftgate Latch Actuator Removal and Installation

1. Remove the liftgate latch remote control. For additional information, refer to Liftgate Latch Remote Control in this section.

SECTION 501-14: Handles, Locks, Latches and Entry Systems 2001 Escape Workshop Manual
REMOVAL AND INSTALLATION Liftgate Latch Removal and Installation

1. Remove the liftgate trim panel.

1. Disconnect the liftgate ajar switch electrical connector.

1. Disconnect the liftgate latch actuating rod.
   1. Open the clip.
   1. Disconnect the actuating rod.

1. Remove and discard the liftgate latch bolts.

1. Remove the liftgate latch.

1. NOTE: Make sure the liftgate latch release rod is not preloading the latch. It should be clipped in a relaxed state with no slack.
   NOTE: Position the liftgate latch release rod by pushing outboard to remove the slack.
   

1. Remove the screws and the liftgate latch actuator