Where is the purge valve solonoid for a 2000 chevy cavalier?

It should be on the drivers side of the engine compartment near the base of the windshield.

Disconnect the electrical connector. Disconnect the vacuum hoses. REplac valve. Reverse to install

Shop for Where is the purge valve... on Google

2000?2001 Chevrolet Imp...
$22.04
Partsgeek.com 2000?2006 Chevrolet Imp...
$18.44
Partsgeek.com 2000 Chevy Impala Air Inje...
$80.95
Google Trusted Store1A Auto.c... 2000?02 Chevy Impala Air Inje...
$80.95
Google Trusted Store1A Auto.c... Standard 2005 Chevrolet Imp...
$26.69
Google Trusted StoreAutoParts... Search Results

How To Install Replace Vapor Canister Purge Valve 3.4L ...

? 2:42
https://www.youtube.com/watch?v=IPKnoxJCIWk
Jul 9, 2014 - Uploaded by 1A Auto Parts
http://www.1aauto.com/vapor-canister-purge-solenoid/i/1aemx00137 In ... How To Install Replace PCV Valve3.4L 2000-07 Chevy Monte Carlo ...

The EVAP Purge valve, on your vehicle, is located in the engine compartment. Yours is on the top of the front-right side (passenger side) of the engine. Just in case you need to know where the EVAP Vent valve/solenoid is located, it is underneath. It is tucked away at the rear part of the car, between the fuel-tank and the right-rear fender well. I hope that helps, good luck.

could have a bad o ring check rings and like could have a crack on the side u cant see

you see code po441 the purge solenoid could be faulty or disconnected. if you have problem with evap switch to vent solenoid you would smell gas fumes in vechicle.check make sure gas cap on tight not leaking because it will set off code po441.

ENGINE VACUUM HOSES ON INTAKE MANIFOLD ARE LOCATED ON MAP SENSOR, PCV VALVE,POWER BRAKE BOOSTER VACUUM HOSE, YOU HAVE VACUUM HOSE TO FUEL PRESSURE REGULATOR.YOU HAVE VACUUM HOSE TO EVAP CANISTER PURGE SOLENOID.

your problem is probably a vacuum hose that goes from the purge valve to the gas tank (crack or broken hose). There should be two of these check both. A broken vacuum line will make the purge valve make a clicking noise that can be mistaken for noisy engine valves.

This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of alot of parts, including the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicles fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engin

heres some things you can try
Remove and reinstall

the gas cap, clear the code, and drive for a day and see if the codes come back.
Inspect the EVAP system for cuts/holes in tubes/hoses
Inspect for damaged or disconnected hoses around the Evap purge solenoid
Check and/or replace the sensor
Check and/or replace the purge valve
Have a professional use a smoke machine to detect leaks

This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.