Where do i locate the wiper motor? - 2001 Toyota Avalon

If your 2006 Citi Golf's front and rear wipers, as well as the wash motors, are not working, there are a few possible causes that you can check:

1. Check the wiper motor: The wiper motor is responsible for moving the wipers. If the motor is not functioning properly, the wipers will not work. You can test the motor using a multimeter to see if it is getting power and check for any visible damage.
2. Check the wiper switch: The wiper switch is located on the steering column or the dashboard and is used to control the wipers. If the switch is not working properly, the wipers will not function. You can test the switch with a multimeter to see if it is sending power to the wiper motor.
3. Check the relay: The relay is an electronic component that controls the power to the wipers. If the relay is faulty, the wipers will not work. You can test the relay with a multimeter to see if it is functioning properly.
4. Check the wiring: Make sure all the wiring is connected properly, and check for any damage or loose connections.
5. Check the wash motor : check if the wash motor is getting power and if it is working properly.

If you're unable to locate the problem or if the problem persists, it's best to take your vehicle to a qualified mechanic to diagnose and repair the issue.

The wiper motor is located underneath the wiper cowling. This is the piece that the wiper arm pivots come out of and the wiper arm blades attach to. The relay is located in the underhood power distribution center. I am unable to give the exact location, however it may be labeled under the cover top cover.

The wiper motor is located under the wiper cowling. You will have to remove the wiper arms and unscrew the screws holding the cowling in place and remove it to access the motor

the wipers are controlled by the lighting control module

Locate the wiper motor, and disconnect the electrical wires from it by unplugging them. The wiper motor is in the engine compartment against the back firewall near the driver's side.
Disconnect the wiper arms from the wiper motor linkage by using the pliers to remove the clip.
Locate the wiper motor in the engine compartment on the back firewall and remove it with the proper size wrench. There are three attaching bolts.
Remove the wiper motor by twisting it around if you have to. The wiper arm linkage will come out with it. good-day !

3Remove the cowl grill under the windshield wipers using the proper size screwdriver. This is the grill that you see under the wiper arms before the engine compartment hood starts.

Read more: How Do I Remove a Windshield Wiper Motor from a 1994 Ford F-250? ' eHow.com http://www.ehow.com/how_7195498_do-motor-1994-ford-f_250_.html#ixzz1odr1irhn

the blower motor is located under the windshield wiper assembly. remove wiper arms. remove plastic cover under wiper arms. then must remove wiper motor and wiper transmission assembly. black plastic cover in center of car needs to be removed then the blower motor is under that.

the wiper motor is located under the black cowel at the bottom of the windshield. remove the wiper arms and the cowel.

Front Wiper Motor Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.

1. Before servicing the vehicle, refer to the Precautions Section.
2. Remove the windshield wiper mounting arm and pivot shaft
   WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
   NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
   
3. Remove the 3 bolts and the wiper motor.
   
   
   
   Fig. Wiper motor and linkage
   

To install:

1. Install wiper motor and bolts.
2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
3. Install windshield wiper mounting arm and pivot shaft.
4. Check wiper operation.

Rear Wiper Motor - Removal & Installation

1. Remove the rear pivot arm.
2. Remove the rear wiper motor shaft nut cover
3. Remove the rear wiper motor shaft nut.
4. Open the lift gate window.
5. Remove the rear wiper motor cover trim panel.
6. Disconnect the electrical connector.
7. Remove the 2 rear window wiper motor nuts
8. Remove the rear window wiper motor.
   
   
   Fig. Rear wiper motor view-2008 model shown, other years similar
   

To install:

1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
2. Reconnect the electrical connector.
3. Install wiper motor cover trim panel.
4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
5. Install shaft nut cover.
   
6. Check wiper operation.

Good luck (remember rated this post).

check the fuses under the dash and under the hood

failing that go to auto zone they can show you the location and quote the parts price too
remem ber to turn on wipers and turn on ignition dont start the car look under hood listen for winding noise locate noise locate wiper motor

if making wiring noise remove and re conect wiper arms inside as they are prone to poping off if over loaded like when frozen to wind screen they pop the conector rather than burn the motor out ]

Im looking for a way to get at the rear wiper motor.How do you get the panaling off