Cars & Trucks Logo

Related Topics:

Konrad Brandstetter Posted on Nov 25, 2015
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Eng runs then dies after a few seconds on honda crv 2004 since changing crankshaft pulley seal

1 Answer

Pablo Gonzalez

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.

  • Master 733 Answers
  • Posted on Apr 15, 2016
Pablo Gonzalez
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.

Joined: Sep 03, 2009
Answers
733
Questions
0
Helped
266251
Points
2189

Make sure the crankshaft sensor and harness weren't damaged during installation. Check to see if you have a check engine light. If so put a scanner on it and see what fault(s) are present.

5 Related Answers

Anonymous

  • 28 Answers
  • Posted on Aug 18, 2008

SOURCE: crankshaft pulley timing marks

the red mark is where the timing is supposed to be after u have bypassed the electronic advance.the first white line on the left is tdc.
thanks for useing fixya

Ad

Anonymous

  • 1 Answer
  • Posted on Dec 29, 2008

SOURCE: 2004 honda radio code

The code for my 2004 CRV was on the side of the glove compartment next to the radio. hope this helps

Anonymous

  • 57 Answers
  • Posted on May 12, 2009

SOURCE: 2004 honda crv brake won't release

Your emergency brake is a mechanical brake system that is indipendant of the regular hydrolic system. If the red brake light on the dash is on make sure it's the emerg. brake and not a problem with the fluid level or the calapers sticking. the best way to check the emerg. brake is to rase both rear wheels off the ground and spin them. If they spin, the emerg. brake is not locked up. If they don't spin, take the rear tires off and the brake drums. (you may have rear disk brakes.) check the springs to insure they are all hooked up properly. If there is no problem there, follow the parking brake cable to check for damage. The cable is like a brake cable on a bike, If the inner cable is binding inside the cable sleeve,the brake wont release. If you have rear disc, it's probly a bad calaper.The park brake cable is attached to the calapers. Rember if it wont run it's annoying but if it won't stop, it's deadly. DON"T experiment with brakes!!! If in doubt, take it to a pro.

mtous2162

  • 58 Answers
  • Posted on Jun 04, 2009

SOURCE: 2002 honda crv air filter change

Hi!

Can you specify if you are referring to the engine intake air filter or the cabin air filter?
If you are referencing the cabin air filter, the attached youtube video should help.

I originally created the video for the Odyssey, but found out after looking at my dad's CRV that it is essentially the same procedure as the Odyssey, and have also noticed that the same stands true for most Honda vehicles built between 2005 and 2009.

Happy motoring!

Anonymous

  • 1 Answer
  • Posted on Aug 12, 2009

SOURCE: How do I change the transmission fluid in my 2004

ourhowse, you may know cars, but you DON'T know the CRV. Both the automatic and manual transmission have drain plugs basically like the oil pan. Look at several of the online videos.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Engine making loud noise when running I removed the serpentine belt and stop?

Turn all the pulleys by hand. Chances are you will be able to tell if there are bad bearings in cone of the following: Power steering pump, alternator, idler pulley, A/C compressor. The one that is failing will probably feel rough when you turn it or have a lot of play in it.
0helpful
1answer

Oil leak on a 2004 honda civic i changed oil pan gasket (felpro) crank shift gasket but it's still leaking

If it's behind the pulley wheels it could be the crankshaft oil seal myself I would remove the timing belt cover and see if you can see it leaking
1helpful
1answer

Crv vibrates for a few seconds as if going over rumble strips 2004

Check cv joints and check loose bush in diff casewhere the shaft goes in. Try lifting up and down as I think you have a problem with the drive shafts binding up
1helpful
2answers

Honda 2004 CRV "D" light

There are a lot of lights please be more clear on which light is flashing. If it is the service engine soon light you will have to run a diagnostic test on it.
0helpful
1answer

4cyl 2000 honda accord engine stalls while idling, recently died and will only start for short periods... possible problems/solutions?

check for spark and fuel after it dies.

If there is spark but no fuel, then the fuel pump may be bad or a clogged fuel filter.

If there is fuel but not spark, then the ignition control module or the ignition coil could be bad.

Also, check that the timing belt is timing the engine correctly.
Timing Belt & Balancer Belt

Removal & Installation

2.3L Engine

To Remove:



  1. Record anti-theft code for radio.
  2. Disconnect battery negative cable then positive cable.






    honda-03-23-3542.gif



  3. Turn crankshaft pulley until TDC is achieved.
  4. Raise and safely support vehicle.
  5. Remove front tire assembly.
  6. Remove splash shield.
  7. Remove power steering belt.
  8. Remove alternator and alternator bracket.
  9. Safely support engine under oil pan.





    Upper bracket removal
    honda-03-23-3420.gif



  10. Remove stop, detach ground cable and remove upper bracket.
  11. Remove cylinder head cover.
  12. Remove upper cover.
  13. Remove dipstick and tube assembly.
  14. Remove crankshaft pulley.
  15. Remove adjusting nut rubber seal and remove lower cover.





    Timing belt/balancer belt removal
    honda-03-23-3544.gif



  16. Loosen adjusting nut 1 turn.
  17. Push up on balancer belt tensioner to relieve belt tension.
  18. Push down on timing belt tensioner to relieve belt tension.
  19. Tighten adjusting nut 1 turn.
  20. Remove balancer belt and timing belt.


To Install:


NOTE: Clean balancer belt drive pulley, timing belt pulleys and
upper/lower timing cover prior to belt installation.








honda-03-23-3425.gif






  1. Set timing belt drive pulley to TDC by aligning dimple on pulley with dimple
    on oil pump.






    honda-03-23-3426.gif



  2. Set camshaft pulley to TDC so that "UP" mark is at top and grooves align
    with top of cylinder head.





    Timing belt installation
    honda-03-23-3549.gif



  3. Starting with driver pulley, install timing belt in a counterclockwise
    sequence.
  4. Loosen and ten retighten adjusting nut.
  5. Install balancer belt drive pulley.
    NOTE: Inspect rubber seal on lower cover and replace as necessary.

  6. Install lower cover.
  7. Install crankshaft pulley and bolt.
  8. Rotate crankshaft pulley counterclockwise several times to seat belt.
  9. Loosen adjusting nut 1 turn.
  10. Rotate crankshaft counterclockwise 3 teeth on camshaft pulley.
  11. Tighten adjusting nut to 33 ft lb (44 Nm).






    honda-03-23-3542.gif



  12. Turn crankshaft pulley until TDC is achieved.






    honda-03-23-3426.gif



  13. Ensure that camshaft pulley "UP" mark is at top and grooves align with top
    of cylinder head.
  14. Remove crankshaft pulley and lower cover.
  15. Rotate crankshaft to TDC again and lock timing belt adjuster arm with a 6 mm
    timing cover bolt.
  16. Loosen adjuster nut 1 turn and ensure that belt tensioner freely moves.
  17. Push tensioner up and tighten adjusting nut.





    Balancer shaft alignment
    honda-03-23-3556.gif



  18. Remove bolt and washer from maintenance hole.
  19. Using a 6 X 100 mm bolt, scribe a mark 2.9 in (74 mm) from end.
  20. Insert bolt into maintenance hole and hole in balancer shaft.
  21. Install bolt up to scribed line.





    Balancer shaft alignment
    honda-03-23-3557.gif



  22. Align groove on balancer shaft with pointer on oil pump housing.
  23. Install balancer belt and loosen adjusting nut 1 turn to tension.
  24. Retighten bolt.





    Balancer shaft alignment
    honda-03-23-3556.gif



  25. Remove bolt from maintenance hole and install bolt and washer. Tighten to
    22 ft lb (29 Nm).
  26. Reinstall crankshaft pulley.
  27. Loosen adjusting nut 1 turn.
  28. Rotate crankshaft pulley counterclockwise 1 turn and tighten adjusting nut.
  29. Remove bolt from timing belt adjuster arm.
    NOTE: Inspect rubber seal on lower cover and replace as necessary.

  30. Remove crankshaft pulley.
  31. Install lower cover.
  32. Install seal at adjusting nut.
    NOTE: Crankshaft pulley, bolt and washer must be cleaned prior to
    installation.

  33. Lubricate crankshaft pulley bolt between head and washer and bolt threads
    with clean engine oil.






    honda-03-23-3537.gif



    CAUTION
    Do not use impact wrench to perform
    following step.

  34. Install crankshaft pulley and tighten bolt using special tools to 181 ft
    lb (245 Nm)
    .
  35. Install dipstick/tube assembly.
  36. Install upper cover. Tighten bolts to 9 ft lb (12 Nm).
  37. Install cylinder head cover.
  38. Install alternator bracket and alternator.
  39. Install power steering pump belt and alternator belt.





    Upper bracket installation
    honda-03-23-3420.gif



  40. Install upper bracket and tighten fasteners in proper numbered sequence.
  41. Install stop.
  42. Install battery and enter radio anti-theft code.


prev.gif next.gif
2helpful
1answer

How to replace Honda front Crankshaft Seal

Have to take off the crankshaft pulley to get at the Crankshaft Seal.

Use a hooked seal remover to dig in and pull the seal out without damaging sealing surfaces.

0helpful
1answer

How to find the 1st cylinder on honda crv 2001 model

The first cylinder is the one closest to the crankshaft pulley.
3helpful
1answer

How to change a serpentine belt for a 2004 honda crv?

pull up on thr idler pulley with a good solid metric wrench and slide it off, once off, check all your pullys for lose bearings especially the alternator...replace the belt too while you at it.
0helpful
1answer

Honda accord lxi 89

yes it is most likely the crankshaft seal or the camshaft seal the only way to make sure is to pull timing cover using 10 mmm sockets and youll have to remove belts and pulleys using 12mm and 14mm sockets and wrenches and pulley puller also it is not easy but you need to be sure and to replace the seals youll need to remove those anyways. Purchase a repair manual to assist you in this job at local parts store haynes or chiltons will do about $20.00 or so.
Not finding what you are looking for?

168 views

Ask a Question

Usually answered in minutes!

Top Honda Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...