Location of MAP sensor on 2002 Alero GX 2.2? - Cars & Trucks

ask the dealer or , go there and see part for the car there
and see what transmission it is, for 2002 the move to 2003
and see if the same (gm parts)
there are 2 engines used, why post at all lacking such a key fact?
2.2L or 3.4liter, v6 is latter.and transmission vary buy engine max power torque, and more, gear counts for economy.

Oldsmobile Alero
or ask any engine rebuilder selling engine that (ever google that)
Or ask the shop doing it.
I'm there now. gm parts.
2002 , 2.4L 89059799 sku
fits all these

2002 Chevrolet Cavalier Base, LS, LS Sport 2.2L L4 - Gas 2002 Oldsmobile Alero GL, GLS, GX 2.2L L4 - Gas 2002 Pontiac Grand Am SE, SE1 2.2L L4 - Gas 2002 Pontiac Sunfire GT, SE 2.2L L4 - Gas 2002 Saturn L100 Base 2.2L L4 - Gas 2002 Saturn L200 Base 2.2L L4 - Gas 2002 Saturn LW200 Base 2.2L L4 - Gas
2003 there shows
89059802 , a diffr, sku!! shows fitments 03

2003 Oldsmobile Alero GL, GLS, GX 2.2L L4 - Gas 2003 Pontiac Grand Am SE, SE1 2.2L L4 - Gas 2003 Saturn L200 Base 2.2L L4 - Gas 2003 Saturn LW200 Base 2.2L L4 - Gas
that is the GM answer, others like engine builders/sellers
my say different even tell you what must be changed to do it

1 minutes work me. just reading at gm.com

check this wiring digram

http://www.bigcee.com/faq/KLR650-color-wiring-diagram.jpg


You can also buy a wiring diagram from the following site..

http://www.ahdol.com/ford_wiring_diagrams.html

2002 Jetta 2.0l does not have a MAP sensor.

2002 Jetta 1.9l TDi MAP sensor location is at the top of the intercooler just behind the passenger (right) headlamp assembly.

Here is a diagram of where the map sensor is located on this particular vehicle, i have also included the removal and installation procedures as well

Hope this helps....

REMOVAL PROCEDURE

1. Remove the air cleaner outlet resonator.
2. Disconnect the manifold absolute pressure (MAP) sensor.
3. Remove the MAP sensor attaching screws (1).
4. Remove the MAP sensor vacuum hose (2).

INSTALLATION PROCEDURE

1. Connect the vacuum hose (2).

NOTE: Refer to Fastener Notice in Service Precautions.

1. Install the MAP sensor attaching screw (1).

Tighten
Tighten the screw to 6.5 N.m (5.7 lb in) .

1. Connect the MAP sensor connector.
2. Reinstall the air cleaner outlet resonator.

The MAP sensor mounts to the driver side of the intake manifold plenum.

Removal & Installation

1. Remove the negative battery cable.
2. Disconnect the electrical connector from the MAP sensor.
3. Remove bolts from sensor.
4. Remove sensor.

To install:

1. Bolt sensor to intake.
2. Attach electrical connector to sensor.
3. Install the negative battery cable.

Hello sbehnke09
The map sensor is located on the intake manifold between the throttle body and the valve cover. Hope this is helpful.

2.2 liters 4 cylinder in-line front engine with 86 mm bore, 94.6 mm stroke, 10 compression ratio, double overhead cam and four valves per cylinder

Try looking on the exhaust pipe up close to the exhaust header, it should be close to the "Y" in the pipe

I have a 1999 Oldsmobile Alero and my car was running rough and stalling. Also when the car was shifting, it was making a "thud" sound. My service engine light was on, so I took it to Autozone to run their diagnostic tool. It came back with code P0108 and they advised me to check my vacuum hoses as a possible solution. I looked and found that my air hose running from my throttle body to my map sensor was disconnected. I reconnected the hose and the engine ran normally and didn't make any "thud" sound when shifting. My car is back to normal. So check your hoses. If its still running rough, you may need to replace your map sensor.

on the air filter intake hose