How do i remove a rear view mirror - 2007 Jeep Commander Rocky Mountain

glass and motor availbable separately

Removal
NOTE: Do not remove the mirror assembly when repairing the individual mirror part. Individual mirror parts can be installed without removing the mirror assembly.

1. Remove the front door trim panel; refer to Section 501-05.

1. Remove the outside rear view mirror access water shield.

1. Remove the speaker.
   1. Remove the screws.
   1. Disconnect and remove the speaker.

1. Disconnect the outside rear view mirror electrical connector.

1. Remove the outside rear view mirror.
   1. Remove the nuts.
   1. Remove the outside rear view mirror.
      • Feed the outside rear view mirror wiring through the opening in the front door.

here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal

1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).
   
   
   
   
   

1. Remove the wire clip.
   

1. Disconnect the power outside rear view mirror electrical connector.
   
   
   
   
   

1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.
   
   
   
   
   

Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal

1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws.
   
   
   Remove the outside rear view mirror mounting hole cover.

Installation
To install, reverse the removal procedure. Mirror Control
Removal

1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).
   
   
   

remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation

1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
   

1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
   

1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
   

1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
   

1. To install reverse Removal procedure.
   

------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation

1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
   

1. Remove front door trim panel (23942). Refer to Section 01-05 .
   

Trim Panels, Door Front—Town Car
Removal

1. Snap out two door pull strap retaining screw covers. Remove screws.
   

1. Remove three screws on front and rear side and center of front door trim panel (23942).
   

1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
   
   Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
   

1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.
   
   Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
   

1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
   

1. Remove the door trim panel.
   

1. Disconnect two electrical connectors.
   

1. Remove nut from outside rear view mirror mounting base.
   

1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
   

1. Remove screw from outside rear view mirror base.
   

1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
   

1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-
   

There is a small screw in the mirror, an allen (or hex) wrench fits in it.

is it just the glass that broke?

Exterior Mirror Glass Removal

1. Position the inner edge or the exterior rear view mirror glass to its maximum travel.

1. WARNING: Place a shop towel between the exterior rear view mirror glass and the hand to avoid personal injury in the instance of glass breakage.
   Grasp the outboard edge of the exterior rear view mirror glass and pull outward.

1. Remove the exterior rear view mirror glass.
   • If equipped, disconnect the heated rear view mirror glass electrical connectors.

Installation

1. If equipped, connect the heated rear view mirror glass electrical connectors.

1. NOTE: An audible click will be heard during installation.
   Press firmly in the center of the exterior rear view mirror glass until it snaps onto the exterior rear view mirror motor.

Mirror — Outside Rear View Removal
NOTE: Do not remove the exterior mirror assembly when repairing an individual part. Individual components can be installed without removing the exterior mirror.

1. Disconnect the battery ground cable (14301).

1. Remove the front door trim panel; refer to Section 501-05.

1. Remove the speaker.
   1. Remove the screws.
   1. Disconnect the electrical connector.
   1. Remove the speaker.

1. Remove the outside rear view mirror (17682).
   1. Disconnect the power mirror wiring clips.
   1. Remove the outside rear view mirror nuts.
   1. Remove the outside rear view mirror.
      • Feed the power mirror wiring through the opening in the front door (20124).

Installation

1. NOTE: When the battery (10655) is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
   To install, reverse the removal procedure.

are you trting to tighten the mirror glass or the mirror where it attaches to the body? I don't think glass is removable in 99. Only can try to press on glass to seat if unseated. not too hard.

1. Remove the front door trim panel; refer to Section 501-05 .
2. go to car-part.com for a used mirror. Page with * is cheapest seller.

1. Remove the speaker.
   1. Remove the screws.
   1. Disconnect the electrical connector.
   1. Remove the speaker.

1. Remove the outside rear view mirror (17682).
   1. Disconnect the power mirror wiring clips.
   1. Remove the outside rear view mirror nuts.
   1. Remove the outside rear view mirror.
      • Feed the power mirror wiring through the opening in the front door (20124).

------------------------------------------------------

----------------------------
SECTION 501-09: Rear View Mirrors 2001 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Glass, 2001 model Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.
NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors

1. Position the glass in the full up position.

1. Locate the notch at the bottom of the exterior mirror glass.

1. Release the exterior mirror glass.
   1. Insert a long flat-bladed screwdriver in the notch.
   1. Push the screwdriver into the notch until the glass is released.

Heated mirrors

1. Position aside the exterior mirror glass.

1. Disconnect the electrical connectors.

All mirrors

1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.

Installation
Heated mirrors

1. Connect the electrical connectors.

All mirrors

1. Position the exterior mirror glass on the exterior mirror motor.

1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.

SECTION 501-09: Rear View Mirrors 2001 Villager Workshop Manual REMOVAL AND INSTALLATION Mirror —Exterior Rear View Removal

1. Remove the front door trim panel. For additional information, refer to Section 501-05 .

1. Remove the upper speaker.
   1. Disconnect the electrical connector.
   1. Remove the bolts.
   1. Remove the speaker.

1. Position the watershield aside.

1. Remove the exterior rear view mirror access panel.

1. Disconnect the exterior rear view mirror electrical connectors.
   • Release the wiring harness locator.

1. Remove the exterior rear view mirror.
   • Remove the bolts.
   • Feed the wiring harness through the door opening.

1. Remove the front door trim panel (23942) ; refer to Section 501-05 .
   • Peel back the watershield.

1. Remove the rear view mirror mounting hole cover (17K709).

1. Disconnect the power mirror electrical connector.

1. Remove the outside rear view mirror (17682).
   1. Remove the screws.
   1. Remove the outside rear view mirror.

please rate as fixya if this works for you.

There are two tiny motors in each mirror. one for up/down. One for side to side. They have jack screws (plastic) that fit into the motors.

You can manually put your hands on either side of the mirror and force adjust it. If you hear a ratcheting sound, the jack screws are OK. Then repeat with hands on top and bottom.

If you hear ratcheting and mirror stays where you stop it, that means one of the motors is bad. The motor assembly is available as a separate part.

-------------------------------------------------------------------------------------
Mirror Motor—Crown Victoria, Grand Marquis
Removal and Installation

1. Disconnect battery ground cable. Refer to Section 14-01 .
   

1. Remove outside Rear View Mirror Glass as outlined.
   

1. Remove Outside Rear View Mirror as outlined.
   

1. Remove two screws from outside rear view mirror motor.
   

1. Remove outside rear view mirror housing from outside rear view mirror base.
   

1. Disconnect connector and remove outside rear view mirror motor from mirror housing.
   

1. To install, reverse Removal procedure.
   

Might be cheaper to buy used irror at car-part.com. Look for * to find page with cheapest part. Or, EBay. Good luck