1995 Chevrolet Lumina Logo
Jbryan
Jbryan Posted on Oct 25, 2015
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

3.1l. Where is the crankshaft position sensor?

Answer This Question

1 Answer

Terry Hair

Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

  • Chevrolet Master 4,134 Answers
  • Posted on Oct 25, 2015
Terry Hair
Chevrolet Master
Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

Joined: Sep 15, 2011
Answers
4134
Questions
2
Helped
1091493
Points
16804

Which one? There are two crankshaft position sensors on the 3.1L.
One is the 24X sensor. It is located behind the crankshaft pulley, installed into the timing cover. The other sensor, the 7X sensor (this is the one that is it fails will cause a no-start condition), is located on the outside of the engine block, close to the crankshaft.

5 Related Answers

Anonymous

  • 491 Answers
  • Posted on Jan 09, 2009

SOURCE: changing spark plugs 95 chevy lumina van

you will have to take off the coil packs and move them out of the way. then go in from the top. its kinda tight but just move whatever else is in the way

Ad

Anonymous

  • 39 Answers
  • Posted on Feb 06, 2009

SOURCE: Where is the camshaft position sensor located-99 Chevy Lumina 3.1

It's held down by one bolt right above the timing chain cover. It's next to the head that's facing toward the front of the car.

Anonymous

  • 1 Answer
  • Posted on Feb 27, 2009

SOURCE: a95 chevy lumina cranks but will not start.

ignition switch under coils

Anonymous

  • 667 Answers
  • Posted on Mar 20, 2009

SOURCE: how to test crank sensor 95 ram van 3.9

sometimes you can test the sensor with a multimeter(volt meter that measure OHMS), it should have some reading, if it is open(no reading) it is bad. Some autozone locations can test this sensor

co7196

Ned C Cook

  • 3433 Answers
  • Posted on Jun 12, 2009

SOURCE: 93 chevy lumina crank sensor location

front of engine just about 11:00 over crank pullry

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

Crankshaft position sensor location 93 ranger 4.0 4x4
https://www.google.com/search?q=Crankshaft+position+sensor+location+93+ranger+4.0+4x4&rlz=1C1CHBF_enUS982US982&oq=Crankshaft+position+sensor+location+93+ranger+4.0+4x4&aqs=chro -------------------https://www.google.com/search?q=Crankshaft+position+sensor+location+93+ranger+4.0+4x4&rlz=1C1CHBF_enUS982US982&oq=Crankshaft+position+sensor+location+93+ranger+4.0+4x4&aqs=chrome..69i57j33i299l3.7225j0j7&sourceid=chrome&ie=UTF-8#kpvalbx=_VCj-YqCEB6GpptQPza2F-AU28
Read full answer
Aug 18, 2022 • Cars & Trucks
0helpful
1answer

Where is the crankshaft position sensor?

    Pontiac G6 Crankshaft Position Sensors - AutoZone

    www.autozone.com/1/.../pontiac-g6-crankshaft-position-sensor...
    AutoZonePontiac G6 Crankshaft Position Sensors including Crankshaft Position Sensor - Duralast (SU8213), Crankshaft Position Sensor - Duralast (SU9540), Crankshaft ... images for pontiac g6 crankshaft position sensor
Read full answer
Oct 28, 2015 • 2006 Pontiac G6
0helpful
2answers

We have a 1996 3.1 monte carlo ls we need to replace the crankshaft senor but we cant find it on the motor is there a picture of where one could be
The crankshaft position sensor is a two pin sensor made up of plastic like material. It is located on the back side of the engine block about half way between the oil pan and the top of the block. It can only be accessed by crawling under the car. 33899bbd-15f1-451a-9a7a-a94f8be62e27.png
Read full answer
May 07, 2014 • 1996 Chevrolet Monte Carlo
2helpful
1answer

Troubleshoot crank position sensor location
For testing crank sensor,check the help link below:---How to test Crankshaft Position Sensor? http://fordrepairhelp.blogspot.in/2012/03/how-to-test-ford-focus-crankshaft.html
----------

• How to test Crankshaft Position CKP Sensor?

---------------
Crankshaft Position Sensor Operation?

----------------
Replace Camshaft position sensor and Crankshaft Position Sensor? http://technoanswers.blogspot.in/2012/06/2005-dodge-durango-replace-camshaft.html
----------
GMC Crankshaft Position (CKP) Sensor Replacing? http://schematicsdiagram.blogspot.com/2011/12/gmc-crankshaft-position-ckp-sensor.html

------------
These details will help.
Thanks.

Read full answer
Nov 25, 2012 • 2000 Cadillac Escalade
1helpful
2answers

99 stratus 2.5 v-6/no spark.will crank over.

CRANKSHAFT POSITION SENSOR - 2.5L

REMOVAL
  1. Remove speed control servo from driver's side strut tower.
  2. Remove crankshaft position sensor retaining bolt Crankshaft Position Sensor
  3. Pull crankshaft position sensor straight up out of the transaxle housing.
  4. (Disconnect crankshaft position sensor electrical connector from the wiring harness connector.
INSTALLATION - ADJUSTABLE All vehicles will be equipped with an adjustable crankshaft position sensor. This can be identified by an elongated mounting hole in the sensor.
NOTE: If the removed sensor is to be reinstalled, clean off the old spacer on the sensor face. A NEW SPACER must be attached to the sensor face before installation. If the sensor is being replaced, confirm that the paper spacer is attached to the face of the new sensor Crankshaft Position Sensor and Spacer
  1. Install sensor in transaxle and push sensor down until contact is made with the drive plate. While holding the sensor in this position, install and tighten the retaining bolt to 12 N·m (105 in. lbs.) torque.
  2. Connect crankshaft position sensor electrical connector to the wiring harness connector.
  3. Attach connector to heater tube bracket.
  4. Install speed control servo. Tighten nuts to 9 N·m (80 in. lbs.) torque.
Read full answer
May 19, 2012 • 1999 Dodge Stratus
3helpful
1answer

HELP ! Sensor crankshaft position SUZUKI AERIO SX AWD 2.3L 2005.How to replace under the scheme ?
Welcome to FixYa.com
Crankshaft Position (CKP) Sensor Removal and Installation

Removal

1. Remove engine with transmission from vehicle.

2. Remove transmission from engine and then remove flywheel or drive plate from crankshaft.

3. Disconnect connector from crankshaft position sensor.

4. Remove crankshaft position sensor (1) from cylinder block (2).

Installation

Image

Reverse removal procedure noting the following.

- Check to make sure that crankshaft position sensor (1) is free from any metal particles and

damage.

- Apply engine oil to O-ring of sensor.

- Install crankshaft position sensor to cylinder block (2) with specified torque.

Tightening torque

Crankshaft position sensor bolt a: 6 N.m (0.6 kg-m, 4.5 lb-fl)

- Connect connector and fix wire harness with clamp securely. Thank you for Using FixYa.comKind Regards, LeeYour FixYa Expert and Master Technician
leedavidian_133.png
Read full answer
Feb 06, 2011 • 2005 Suzuki Aerio SX
2helpful
2answers

I need to put a crankshaft sensor but I don't Know its location I already changed the cam sensor. Ronnie
The crank sensor is located on the engine near the flywheel axis of the crankshaft.

Crankshaft Position Sensor Removal & Installation To Remove:
Location of the crankshaft position sensor on the 2.4L engine 90904g51.gif
Location of the crankshaft position sensor on the 3.0L engine 91154g20.gif
Location of the crankshaft position sensor on the 3.3L and 3.8L engines 91154g21.gif
NOTE: On the 2.4L engine, the crankshaft position sensor is mounted to the engine block behind the alternator, just above the oil filter. On the 3.0L, 3.3L and 3.8L engines, the crankshaft position sensor is mounted on the transaxle housing, above the vehicle speed sensor.
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Disconnect the crankshaft position sensor electrical connector.
  4. Unfasten the sensor mounting screw, then remove the sensor from the vehicle by pulling it straight out.
To Install:
NOTE: If the sensor removed is going to be re-installed, clean off the old spacer on the sensor face. A new spacer must be attached to the sensor face before installation. If the sensor is being replaced, be sure that a paper spacer is attached to the sensor face.
  1. Install sensor and push the sensor in until contact is made. While holding the sensor in this position, install and tighten the mounting bolt to 105 in. lbs. (12 Nm).
  2. Connect the crankshaft position sensor electrical connector.
  3. Lower the vehicle.
  4. Connect the negative battery cable.
prev.gif next.gif
Read full answer
Jul 31, 2010 • 1996 Plymouth Grand Voyager
3helpful
1answer

Where is the crankshaft sensor on a v6 2000 chrystler sebring
CRANKSHAFT POSITION SENSOR - 2.5L
REMOVAL
Remove speed control servo from driver's side strut tower.
Remove crankshaft position sensor retaining bolt Crankshaft Position Sensor
Pull crankshaft position sensor straight up out of the transaxle housing.
(Disconnect crankshaft position sensor electrical connector from the wiring harness connector.
INSTALLATION - ADJUSTABLE
All vehicles will be equipped with an adjustable crankshaft position sensor. This can be identified by an elongated mounting hole in the sensor.

NOTE: If the removed sensor is to be reinstalled, clean off the old spacer on the sensor face. A NEW SPACER must be attached to the sensor face before installation. If the sensor is being replaced, confirm that the paper spacer is attached to the face of the new sensor Crankshaft Position Sensor and Spacer

Install sensor in transaxle and push sensor down until contact is made with the drive plate. While holding the sensor in this position, install and tighten the retaining bolt to 12 N·m (105 in. lbs.) torque.
Connect crankshaft position sensor electrical connector to the wiring harness connector.
Attach connector to heater tube bracket.
Install speed control servo. Tighten nuts to 9 N·m (80 in. lbs.) torque.
Read full answer
May 22, 2010 • 1998 Chrysler Sebring
4helpful
1answer

Jsut want to know where crankshaft position sensor
Hi!!

here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


2.3L Engine


The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

0996b43f80202990.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-2.3L engine


3.0L Engine


The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

0996b43f8020299e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-3.0L engine

The cost of the sensor is $23 bucks at AutoZone.

If helpful, click below
Read full answer
Apr 15, 2010 • 2002 Ford Escape
2helpful
2answers

What size "bolt" is used to hold the crankshaft position sensor in place on a 2000 sebring 2.5L I will be changing it out in a dark parking garage and want to have the proper tools.
either a 10mm or 8mm socket.
Read full answer
Nov 20, 2009 • 2000 Chrysler Sebring
Not finding what you are looking for?

View Most Popular

1995 Lumina

  • Cars & Trucks

Related Question

Crankshaft position sensor location 93 ranger 4.0 4x4

  • Cars & Trucks

Related Topics

1,039 views

Ask a Question

Usually answered in minutes!

Popular Questions

Fuel injector fuse is blown, keeps blowing. Engine turns but won't catch and start.

1995 Chevrolet Lumina

Cyl head torque on 05 3.4l chev equinox

1999 Chevrolet Lumina

DIAGRAM OF THE FIRING ORDER CHRYSLER 300 3.6

1998 Chevrolet Lumina

Vauxhall astra auot code P1895 what does it mean

1997 Chevrolet Lumina

I locked my keys in my car. how do you break into

1997 Chevrolet Lumina

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...