Where do I add washer fluid for rear window wiper on a 2000 blazer

They run Inside , you need to replace the Rubber Line.. It is for the Rear Window Sprayer

Your Blazer has two pumps in the tank that you add washer fluid to. One is for the windshield and one for the rear window.

One can get a repair kit that includes a new motor pump and wiring clips, or

one can get the original motor that plugs into the windshield wiper fluid reservoir.

---
Windshield wiper reservoir (gives idea of how to change the windshield wiper fluid pump motor) Removal & Installation To Remove:

1. Disconnect and isolate the negative battery cable.
2. Raise and safely support the vehicle.
3. Remove the right front wheel and splash shield.
4. Disconnect the electrical connectors from the pumps and detach the rear washer hose.
5. Place a drain pan under the reservoir if it contains fluid.
6. Disconnect the front washer hose at the wiper unit in the engine compartment. NOTE: The front hose will be removed with the reservoir.
   
7. Let the fluid drain from the reservoir.
8. Remove the mounting screws and the reservoir.

To Install:

1. Install the fluid reservoir with the mounting screws.
2. Connect the front washer hose in the engine compartment.
3. Connect the electrical connectors and rear washer hose.
4. Install the splash shield.
5. Install the right front wheel.
6. Lower the vehicle.

I have the same problem with my 2000 chevy blazer as skornec had posted. I kinda already figured the hose or spray nozzle was plugged. But the problem with checking those items is that I don't know where the hose is located to the back wiper. And the only thing that could be I see that could be the spray nozzle doesn't even have holes that washer fluid could spray from. So basically I just would LOVE if someone could please inform this lame brain of where to find the spray nozzle on the rear window and where in the interior of my blazer does the washer hose run.

1999 blazer i m pretty sure uses the same reservoir, its easy to check, look at bootom of res and there should be to pumps. a good way to test wiring and washer button is to wire the rear to frt and hit rear washer button and it should spray frt window, or just use a test light and check for a good ground and power when button is hit hope this helps.

fuse or broken wire

You may have a line disconnected or the tank may be emply? Are all lines connected at the rear blade? I believe the fluid comes from the front tank under the hood. Check the lines from the tank.
Also check the pump. Can you hear the pump when using rear wiper/washer?

what is P13K?

check the fuse first. dealer can hook up NGS Tester and get fault codes to see what is wrong.

Principles of Operation
NOTE: The generic electronic module (GEM) will not activate the rear wiper system if either the liftgate or the liftgate glass is ajar. If either the liftgate or the liftgate glass becomes ajar while the rear wiper is in operation, the GEM will park the rear wiper motor.
There are two distinct modes of wiper operation:

• Off Mode: In this mode, there is no rear wiper activity, and the wiper motor will be in the PARK position.
• Interval Mode: This mode is selected when the rear wiper switch is in either the Interval 1 or 2 position. When this mode is selected, the rear wiper motor is driven up onto the glass by activating the rear wiper UP relay. When the wiper motor HIGH/LOW/PARK position input reaches the high position, the UP relay is deactivated and the DOWN relay is activated to reverse the wiper motor direction. When the wiper motor reaches the LOW position, as determined by the HIGH/LOW/PARK position input, the GEM deactivates the DOWN relay and will begin a new wiper cycle 1 to 10 seconds later, depending on the interval position selected.

To engage the rear window washer, rotate the rear window washer selector downward to the WASH position. The rear window wiper will run as long as the WASH position is selected. When the rear window washer selector returns to the OFF, INT 1 or INT 2 position, the washer will stop immediately, but the rear window wiper will continue for two to three sweeps and then return to its previous mode of operation.
The low washer fluid indicator chime warns that the washer fluid level is low. The low washer fluid indicator chime is a single tone with a duration of one second. The chime will sound when the low washer fluid indicator is initially activated.
The low washer fluid indicator warns that the fluid level in the washer reservoir is low. The low washer fluid indicator will illuminate when the washer fluid level is low and the ignition switch is in the RUN position.
The low washer fluid indicator will deactivate when the washer fluid reservoir is filled and the ignition switch has been cycled from RUN to OFF, then to RUN.
Inspection and Verification

1. The wiper/washer system is a generic electronic module (GEM) controlled system; refer to Section 419-10 .

1. Verify the customer concern by operating the wiper/washer system.

1. Visually inspect for obvious signs of mechanical and electrical damage.

Visual Inspection Chart Mechanical Electrical

• Hoses to windshield washer pump
• Wiper linkage

• Fuses 6 (5A), 8 (5A), 15 (5A), and 20 (5A)
• Wiring harness
• Loose or corroded connector(s)
• Relays
• Motors
• Multifunction switch
• Washer fluid level switch

----------------------------------------

• The wipers are inoperative — rear

• Fuses 6 (5A), 8 (5A), 15 (5A), and 20 (5A).
• Circuitry.
• GEM.
• Multifunction switch (wiper/washer switch).
• Rear wiper up relay.
• Rear wiper down relay.
• Rear wiper motor.

On my 2000 Blazer you just had to Fill the Tank under the Hood. Had a Line that ran to the Rear Wiper From There.

the little pump inside the washer fluid reservoir is bad, replace it