No instrument lights - 1998 Subaru Legacy

Chrysler PT Cruiser Dash Lights Instrument Cluster lights ...

? 5:02
https://www.youtube.com/watch?v=Xl8B78vBDXk
Jul 8, 2015 - Uploaded by World Mechanics
Chrysler PT Cruiser Dash Lights Instrument Cluster lights ON & OFF Blinking COMMON PROBLEM! We took ...

PT Cruiser Dash Light/Instrument Cluster Removal and ...

? 12:58
https://www.youtube.com/watch?v=rsITrfvYBIE
Jan 22, 2015 - Uploaded by WeekendHandymen
PT Cruiser Dash Light/Instrument Cluster Removal and Replacement ... Chrysler PT Cruiser Dash Lights ...

PT Cruiser dash lights replacement - YouTube

? 3:03
https://www.youtube.com/watch?v=S1dFuACAMk0
May 9, 2013 - Uploaded by 2stroketurbo
A quick overview of how to replace burned out dash lights on a 2005 ... How To Install Replace Engine Ignition ...

There is no relay for the instrument panel. The dash lights and interior lights have fuses. The instrument panel itself is illuminated by the Central Power Module.

Check 20Amp LP Park Fuse in Underhood Fuse Block (mounted to right strut tower) Check 15Amp Tail Lic. Lamp Fuse In IP Fuse Block.

There are a total of six fuses that control exterior lights and dash lights. Check all of these Fuses: 10, 21, 3, 7, 13, 33
Does the high mount stop light work when you apply the brakes?

Which light is out? Is it an instrument cluster light, or one on the temperature or A/C cluster? It it's an instrument cluster light, here is the process: (I'm assuming the 99 is similar to the 98) Remove the bottom dash panel under the steering wheel, remove the instrument cluster cover around the steering column. This will reveal the screws that hold your instrument cluster cover in place. Remove this cover and you can then see and remove the 4 screws holding your instrument cluster in place. Pull your instrument cluster out, remove the main wire connector, then you have access to all the instrument cluster lights on the back side. Hopefully you remember which one is out!

Check out the "Instrument Cluster Light Bulbs" section below:

2002 Volkswagen Passat - Repair Manual - Chassis Electrical (excerpt)

Dome/Map/Cargo Light

1. Disconnect the negative battery cable.
2. Remove the bulb from its retaining clip contacts. If the bulb has tapered ends, gently depress the spring clip/metal contact and disengage the light bulb, then pull it free of the two metal contacts.

To install:

1. Before installing the light bulb into the metal contacts, ensure that all electrical conducting surfaces are free of corrosion or dirt.
2. Insert the bulb into the holder. If the contacts have small holes, be sure that the tapered ends of the bulb are situated in them.
3. To ensure that the replacement bulb functions properly, activate the applicable switch to illuminate the bulb which was just replaced. If the replacement light bulb does not illuminate, either it is faulty or there is a problem in the bulb circuit or switch. Correct as necessary.
4. Install the cover until its retaining tabs are properly engaged.
5. Connect the negative battery cable.

Instrument Cluster Light Bulbs
The instrument clusters installed on these models are one of 2 types and distinguished by the instrument lighting color, either green or blue.
On models with green instrumentation, only the control light bulbs are replaceable. Should any other failure occur, the instrument cluster must be replaced.
On models with blue instrumentation, none of the components are replaceable. Should a failure occur, the instrument cluster must be replaced.

Map Lights

1. Disconnect the negative battery cable.
2. Remove the bulb from its electrical connector.
3. Installation is the reverse of removal.

Your dash light fuse is usually labeled instrument lights or inst. lts. on your fuse panel cover . It is important to note that the instrument light fuse is fed by the brake light fuse . So , make sure your brake lights are working properly first . If your brake light fuse is blown , your instrument lights will not work .

This color code works for 87-93 mustang factory radio; it might work on yours as well. I'm not sure if it has the same fuses though.

Radio Connector:

Light Green / Yellow - Hot at all times (Fuse 8)
Yellow / Black - Hot in ACC or Run (Fuse 11)
Light Brown / Red - Goes to instrument panel dimming rheostat (Fuse 4)
Red - Ground
White / Purple - Hot in ACC or Run (Fuse 11)

Speaker Connector:

White / Light Green - (+) Right Instrument Panel & Door Speaker
Dark Green / Orange - (-) Right Instrument Panel & Door Speaker
Brown / Pink - (+) Right Rear Speaker
Pink / Light Brown - (-) Right Rear Speaker
Pink / Light Green - (+) Left Rear Speaker
Tan / Yellow - (-) Left Rear Speaker
Light Brown / White - (+) Left Instrument Panel & Door Speaker
Orange / Light Green - (-) Left Instrument Panel & Door Speaker
Hope this helps.

I'm not sure what year you have but this color code works for 87-93 mustangs.

Radio Connector:

Light Green / Yellow - Hot at all times (Fuse 8)
Yellow / Black - Hot in ACC or Run (Fuse 11)
Light Brown / Red - Goes to instrument panel dimming rheostat (Fuse 4)
Red - Ground
White / Purple - Hot in ACC or Run (Fuse 11)

Speaker Connector:

White / Light Green - (+) Right Instrument Panel & Door Speaker
Dark Green / Orange - (-) Right Instrument Panel & Door Speaker
Brown / Pink - (+) Right Rear Speaker
Pink / Light Brown - (-) Right Rear Speaker
Pink / Light Green - (+) Left Rear Speaker
Tan / Yellow - (-) Left Rear Speaker
Light Brown / White - (+) Left Instrument Panel & Door Speaker
Orange / Light Green - (-) Left Instrument Panel & Door Speaker
Hope this helps.

The instrument lights & hazard lights are on the same fuse - marked HZD Lp in the fuse box. If the hazard lights work then you have probably just turned the instrument lights off by the rotary control on the dash.