What is location of pcm....powertrain control module on a 1996 ford f-150 xlt 5.8ltr. 3514x4

The output speed sensor on a 2014 Ford F150 XLT is typically located on the transmission tailshaft or the rear of the transmission case. It is used to measure the rotational speed of the transmission output shaft and send a signal to the vehicle's powertrain control module (PCM) indicating the transmission gear ratio.
I would recommend checking the vehicle's service manual for a more specific location and a diagram of the sensor, as the location and installation may vary depending on the specific transmission model and options your Ford F150 XLT has.
The output speed sensor is typically a small, cylindrical sensor that is mounted to the transmission case. It is connected to the PCM via a harness and may be located near the transmission oil pan or near the output shaft.
If you're unsure of its location or have trouble finding it, a professional mechanic will be able to locate and diagnose any issues with the output speed sensor.

P1633 - Keep Alive Power (KAPWR) Voltage Too Low Description: Indicates the KAPWR circuit has experienced a voltage interrupt. Possible Causes:

• Open KAPWR circuit
• Intermittent KAPWR

Diagnostic Aids: Loss of KAPWR to the powertrain control module (PCM) results in immediate malfunction indicator lamp (MIL) illumination and DTC P1633. Application Key On Engine Off Key On Engine Running Continuous Memory All GO to Pinpoint Test QB .
QB: DTCs P0603 or P1633: Keep Alive Power (KAPWR)
Introduction QB: Pinpoint Tests This pinpoint test is intended to diagnose the following:

• battery terminal condition
• KAPWR wire routing
• harness circuit: KAPWR
• powertrain control module (PCM) (12A650)

Powertrain Control Module (PCM) Connector

For PCM connector views or reference values, refer to Section 6 .


Vehicle Connector Pin Circuit Edge,
F-150,
Five Hundred,
Freestyle,
Mark LT,
MKX,
Montego 190 Pin B54 KAPWR Escape/Mariner,
Focus 150 (50-50-50) Pin B45 KAPWR Expedition,
Fusion,
Milan,
MKZ,
Navigator 140 Pin B54 KAPWR All other vehicles 170 Pin B45 KAPWR
Do you know how to test automotive electrical circuit's using a DMM - digital multi- meter ?

Ford Series 150 1996 fuse box diagram USA version Auto Genius

The Powertrain Control Module (PCM) detects the engine operating and driving conditions, along with the exhaust gas oxygen content. Various switches, sensors and components provide the PCM with information which allows it to control the air/fuel ratio (mixture), emissions and drivability.

To get to the PCM you would have to remove the parking brake and shift consoles and then the gearshift knob and and boot...I know, GREAT place to put a part needing to be serviced!

For Escape and Mariner, the Powertrain Control Module (PCM) is located behind the instrument panel (cowl), center to both driver and passenger sides (access from the engine compartment).

Fig. Powertrain Control Module (PCM) view

Hope this helps (remember to rate and comment this answer).

Powertrain Definition: Internal Control Module Read Only Memory (ROM) Error P0605 FORD Description The ECM consists of a microcomputer and connectors for signal input and output and for power supply. The ECM controls the engine.
Most common cause of this code is a defective ECM (Electronic Control Module), in your year the part is known as the PCM (Powertrain control module)

The Ignition Control Module is integrated within the Powertrain Control Module or PCM on Both 3.0L & the 4.0L

Keep in mind the definitions:
* ECM = Electronic Control Module (prior 1995 computer, OBD1)
* PCM = Powertrain Control Module (1995 and newer, OBD2)

Ford Freestyle 2005 - Powertrain Control Module The PCM is located in the ine compartment, passenger side, mounted to the cowl. Removal & Installation procedure:

1. Retrieve the module configuration.
2. Remove the cowl panel grille.
3. Disconnect the 3 PCM electrical connectors.
4. Remove the bolt and the PCM.

To install:

1. Installation is the reverse of removal.

Hope helps (rememnber rated this).

Powertrain Control Module: Locations
The Powertrain Control Module (PCM) is located in the right-rear side of the engine compartment.

It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.