I have a 2000 volvo i canot cut off the hazard warning flashers

Your cheapest option will be a salvage yard. New, it is $86 because it is part of the control stalk. remove it completely and see if you can fix the spring and latch mechanism in it.

2000 Chevrolet Tahoe Turn Signal/Hazard Warning Flasher

https://www.autozone.com > electrical-and-lighting > 2...
Notes: Hazard Warning and Turn Signal Flasher. 100W Max. With 2 Turn and 4 Hazard. PRICE: 16.49; Wattage: 100 W. Terminal Quantity: 2; LED Compatible: LED.

• 
  

  Chevrolet Tahoe Switch - Hazard Warning - from $53.99+

  https://www.autozone.com > electrical-and-lighting > ta...
  Results 1 - 7 of 7 - Order Chevrolet Tahoe Switch - Hazard Warning online today. Free Same Day Store Pickup. Check out free battery charging and engine ...

00 2000 Chevrolet Tahoe Hazard Warning Flasher - Body Electrical ...

https://www.partsgeek.com > ... > Hazard Warning Flasher
Buy a 2000 Chevrolet Tahoe Hazard Warning Flasher at discount prices. Choose top quality brands AC Delco, API, Standard Motor Products.

The Hazard Warning flasher switch is located in the center of the instrument panel above the radio. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off the Hazard Warning flasher. This is an emergency warning system and should not be used when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. When you must leave the vehicle to seek assistance, the Hazard Warning flasher will continue to operate even though the ignition switch is OFF. NOTE: With extended use, the Hazard Warning flasher may wear down your battery. http://cdn.dealereprocess.com/cdn/servicemanuals/chrysler/2010-townandcountry.pdf

The Combination Flasher, also referred to as the combo-flasher, is mounted to the in-line bracket which is located to the right of the Junction Block. The flasher can be removed by pulling in a rearward direction. The left under panel silencer duct must be removed to access the flasher. The combo-flasher is black in color for ease of identification.
The Turn Signal and Hazard Warning Flasher is combined into one unit called a Combination Flasher (Combo-Flasher). The combo-flasher controls the flashing of the hazard warning system and the turn signal system. An inoperative bulb or incomplete turn signal circuit will result in an increase in flasher speed.

Ref: http://www.10w40.com/questions/auto-repair-questions/where-is-the-flasher-relay-on-a-2000-chrysler-concorde
Good Luck

Interesting, these are on the same circuit.

1) Click the hazards on and off a few times to exercise the switch.
2) Replace the flasher timer relay.
3) I believe that this system has a little computer center, about the size of a machbox and it is located under the dash. Swap this out with one from a junkyard.

mine too did u solve this problem mines a 03 d5 s60

Replacement The turn and hazard flashers are integrated into one flasher on these models. The flasher is located in the hazard warning switch and the hazard warning switch is located on the trim plate. Replace the flasher by unplugging the old one, removing it from the panel, and plugging in the new one.

1. Remove the bezel from the ignition switch.
   

Remove the bezel from the ignition switch

Carefully remove the instrument panel accessory trim plate.


To remove the trim plate, use a suitable prytool to carefully apply pressure at the retaining clip points . . .


. . . then gently pull the accessory trim plate away

Detach the electrical connector from the hazard warning switch.


Unplug the electrical connector from the hazard warning switch . . .

Unfasten the screw securing the hazard warning switch and remove the switch.


. . . then unfasten the screw securing the hazard warning switch and remove the switch from the vehicle


Installation is the reverse of removal.

If your turn signals work, then replace the flasher for your hazards. Turn your key on then give a left turn signal. Listen for the "clicking" sound near your brake pedal and accelerator. Once you locate your turn signal flasher (small, "cylinderical", device) the hazard flasher should be near it. Simply pull out the flasher and replace... just plugs in.

Check out this recall below:
Bulletin No.: 04098A

SPECIAL POLICY
Subject:
04098 - Special Policy Adjustment - Turn Signal/Hazard Warning Flashers 

Condition
Some customers of 1999-2002 Chevrolet Malibu, Oldsmobile Alero, Pontiac Grand Am, and 1999 Oldsmobile Cutlass may have turn signal/hazard flashers that become inoperative.

Special Policy Adjustment
This special policy covers the condition described above for a period of 10 years or 150,000 miles (240,000 km), whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. The repairs will be made at no charge to the customer.

Good luck and hope this helps:
HAZARD WARNING SWITCH REPLACEMENT - ON VEHICLE 
REMOVAL PROCEDURE 

Remove the center air louver deflector. Refer to Air Deflector Louver Replacement - Center Vent. 
Remove the instrument panel cluster. 
Remove the hazard warning switch bezel from the instrument panel using a small-flat bladed tool to release the retainers.
Remove the left side bolt from the hazard warning switch through the instrument panel cluster pocket Remove the right side and center lower bolts from the hazard warning switch through the center air louver deflector pocket.
Reposition the hazard warning switch from the instrument panel to access the electrical connector. 
Disconnect the electrical connectors from the hazard warning switch. 
Remove the hazard warning switch from instrument panel. 

INSTALLATION PROCEDURE
Connect the electrical connectors to the hazard warning switch.
Position the hazard warning switch to the mounting points in the instrument panel. NOTE: Refer to Fastener Notice in Service Precautions.
Install the left side bolt to the hazard warning switch through the instrument panel cluster pocket. Tighten Tighten the left side hazard warning switch bolt to 3 N.m (27 lb in) . 
Install the right side and center lower bolts to the hazard warning switch through the center air louver deflector pocket. Tighten Tighten the left side hazard warning switch bolt to 3 N.m (27 lb in) . 
Install the hazard warning switch bezel to the instrument panel pressing into place until fully seated. Install the instrument panel cluster. 
Install the center air louver deflector. Refer to Air Deflector Louver Replacement - Center Vent.

The V90 indicator flasher unit is built in to the hazard warning switch, you need to pull the switch out of the dash unplug it and replace the switch unit with a new one which simply pushed back into the dash after plugging the conector back in the new one.

The flasher relay is the actual switch.