Replace hazard switch - 2007 Pontiac G6 GT Convertible

What fuse are you pulling ?

Hazard Lamps
The hazard warning switch is part of the turn signal switch. The turn signal switch receives battery voltage at all times through the HAZARD SWITCH Fuse. When the hazard switch is placed in the HAZARD position, battery voltage is applied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher sends a turn signal flasher signal to the turn signal switch. The turn signal switch provides all of the turn lamps and turn indicators with the turn signal flasher signal, simultaneously flashing them on and off.

Turn Signal Lamps
The front turn signal lamps are made up of the front park/turn signal lamps and rear turn signal lamps. The front turn signal lamps flash with the rear turn signal lamps when a turn is initiated using the turn signal/multifunction lever. The turn signals will operate only with the ignition switch in the RUN position and will not operate during hazard flasher operation.
When the ignition is turned to the RUN position, battery voltage is supplied to the TURN SIGNAL Fuse. Battery voltage is then applied through the turn signal fuse circuit to the turn signal switch. When the turn signal switch is placed in the LH or RH position, voltage is supplied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher supplies a turn signal flasher signal to the turn signal switch. With the turn signal switch in the LH or RH position the corresponding turn signal indicator, rear turn signal, and front turn signal receive the turn signal switch signal and will flash. The front turn signals receive the turn signal switch signal from the turn signal switch via the BCM. The turn lamps are permanently grounded.

Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column - Tilt.

The hazard switch is located in the middle of the dashboard, above the radio. If has stopped working, you can order a replacement here:

SWITCH HAZARD DASHBOARD SWITCHES for Mazda Tribute 2001 2006 EC01664H0B

If hazard switch wont stay engaged and the turn signals run through it I would replace hazard switch then retest

I believe it is all one unit built into the hazard switch in the center of your dash. Usually the hazard switch goes out on these. Replace the hazard switch and your turn signal and Hazards should work properly again.

Either 1 of 2 things. Relay inside hazard switch goes bad often. If that is not it, then usually you would end up replacing the actual turnsignal column switch. But a new Hazard switch should do it.

Replacement The turn and hazard flashers are integrated into one flasher on these models. The flasher is located in the hazard warning switch and the hazard warning switch is located on the trim plate. Replace the flasher by unplugging the old one, removing it from the panel, and plugging in the new one.

1. Remove the bezel from the ignition switch.
   

Remove the bezel from the ignition switch

Carefully remove the instrument panel accessory trim plate.


To remove the trim plate, use a suitable prytool to carefully apply pressure at the retaining clip points . . .


. . . then gently pull the accessory trim plate away

Detach the electrical connector from the hazard warning switch.


Unplug the electrical connector from the hazard warning switch . . .

Unfasten the screw securing the hazard warning switch and remove the switch.


. . . then unfasten the screw securing the hazard warning switch and remove the switch from the vehicle


Installation is the reverse of removal.

check the cabel..
check the hazard switch..

if two of them working properly your hazard sould be work...

Check the hazard switch and the connector to hazard switch see if u have the power and earth to hazard switch if there is power and earth to switch then replace ur hazard switch its faulty but if there is no power and earth to switch then it has whirring problem

Check out this recall below:
Bulletin No.: 04098A

SPECIAL POLICY
Subject:
04098 - Special Policy Adjustment - Turn Signal/Hazard Warning Flashers 

Condition
Some customers of 1999-2002 Chevrolet Malibu, Oldsmobile Alero, Pontiac Grand Am, and 1999 Oldsmobile Cutlass may have turn signal/hazard flashers that become inoperative.

Special Policy Adjustment
This special policy covers the condition described above for a period of 10 years or 150,000 miles (240,000 km), whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. The repairs will be made at no charge to the customer.

Good luck and hope this helps:
HAZARD WARNING SWITCH REPLACEMENT - ON VEHICLE 
REMOVAL PROCEDURE 

Remove the center air louver deflector. Refer to Air Deflector Louver Replacement - Center Vent. 
Remove the instrument panel cluster. 
Remove the hazard warning switch bezel from the instrument panel using a small-flat bladed tool to release the retainers.
Remove the left side bolt from the hazard warning switch through the instrument panel cluster pocket Remove the right side and center lower bolts from the hazard warning switch through the center air louver deflector pocket.
Reposition the hazard warning switch from the instrument panel to access the electrical connector. 
Disconnect the electrical connectors from the hazard warning switch. 
Remove the hazard warning switch from instrument panel. 

INSTALLATION PROCEDURE
Connect the electrical connectors to the hazard warning switch.
Position the hazard warning switch to the mounting points in the instrument panel. NOTE: Refer to Fastener Notice in Service Precautions.
Install the left side bolt to the hazard warning switch through the instrument panel cluster pocket. Tighten Tighten the left side hazard warning switch bolt to 3 N.m (27 lb in) . 
Install the right side and center lower bolts to the hazard warning switch through the center air louver deflector pocket. Tighten Tighten the left side hazard warning switch bolt to 3 N.m (27 lb in) . 
Install the hazard warning switch bezel to the instrument panel pressing into place until fully seated. Install the instrument panel cluster. 
Install the center air louver deflector. Refer to Air Deflector Louver Replacement - Center Vent.

the flasher is the hazzard switch and most likely the problem.