What are the head bolt torque settings? - 1993 Toyota Pickup

In the link

https://www.google.com/search?q=2016+Mahindra+Bolero+2.5+NEF.+Torque+settings+for+the+cylinder+head+bolts

..

The head bolt torque specification for a Big Horn model vehicle will depend on the specific make and model of the vehicle, as well as the engine size and type. I recommend consulting the manufacturer's service manual or a reputable mechanic for the correct head bolt torque specifications for your specific vehicle. It is important to use the correct torque specifications to ensure that the engine components are properly secured and to prevent damage to the engine.

In general, head bolts are typically tightened in a specific sequence and to a specific torque specification to ensure proper clamping force and to prevent warping or damage to the cylinder head. It is important to follow the manufacturer's recommended tightening sequence and torque specifications to ensure the proper clamping force and to prevent engine damage.

It is also important to use a torque wrench to accurately tighten the head bolts to the specified torque. A torque wrench allows you to apply a specific amount of torque to the head bolts, ensuring that they are tightened to the correct specification. Using a torque wrench will help to ensure that the head bolts are tightened properly and will help to prevent over-tightening, which can cause damage to the engine.

What are the cylinder head torque settings for a KIA K2700

www.answers.com > ... > Categories > Cars & Vehicles > Asian Cars > Kia
What is the torque specification for the cylinder head on a 2002 Kia Sportage? ... the correct torque for cylinder head bolt of kia pregio 2.7 diesel is 130-135ft-lbs. ... Thehead bolt torque settings, on your Kia 2.7 diesel engine, is 70 pounds per ...

Torque setting Toyota Land-cruiser 80 Series 4.5 1995-98
Engine code: 1FZ-FE, 1HD.
Stage 1: 20 Nm (Start tightening bolts from center to outwards)
Stage 2: 39 Nm
Stage 3: Rotate each bolt by 90 Degrees.
Stage 4: Further rotate each bolt by 90 Degrees

Torque settings for cylinder head bolts for Skoda Fabia 1.4 16v

Cylinder head bolts tightening order:



IMPORTANT NOTE: RENEW BOLTS!

Stage 1: Tightening torque = 30 Nm
Stage 1: Tightening torque = 90 Degrees
Stage 1: Tightening torque = 90 Degrees

Please do rate my response. Thanks!

i am replacing the heads on a GMC 350 cu in engine. what is the final torque of the head bolts?

I need the torque settings and pattern for a Kia Sportage 2.2

Hope this helps, from autozone site. Curt
Application:
Cylinder head bolt torque sequence

Note :
Torque sequence:
---------
front | 3 1 6 |
of | |
vehicle | 5 2 4 |
---------
Step 1: Lightly oil cylinder bolt threads & washers
Step 2: Torque to 22 Ft/Lbs
Step 3: Torque to 51 Ft/Lbs
Step 4: Loosen all bolts 180 degrees
Step 5: Loosen all bolts 180 degrees
Step 6: Torque bolts 1 & 2 to 25 Ft/Lbs
Step 7: Torque bolts 3, 4, 5, 6 to 11 Ft/Lbs
Step 8: Turn all bolts an additional 80 to 90 degrees
Step 9: Turn all bolts an additional 80 to 90 degrees
*** CAUTION ***
engine uses Torque To Yield head bolts (TTY) that
permanently stretch during the initial installation.
New head bolts must be used when cylinder head is
replaced or re-installed to obtain proper Torque.

Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Hope this helps everyone, sorry it seems longwinded but that is how it's written in the manual.