How to test pcm contro

When you disconnected the battery you also disconnected all the systems for the immobilizer and security system. It needs resetting.

Ford anti theft code 13 incorrect key . Most likely the chip in your key is wore out . After three incorrect trys it goes into lock mode witch takes up to 90 mins to clear

You can't just change parts an expect it to work , software , modules won't let it work . You have to take it to the dealer or have a mobile lock smith fix it , reprogram it ETC...
Anti-Theft -Passive Anti-Theft System (PATS) The passive anti-theft system (PATS) contains the following components:

• theft indicator
• encoded ignition key
• PATS transceiver module
• powertrain control module (PCM)
• standard corporate protocol (SCP) communication network
• Passive Anti-Theft System (PATS) -Diagnostic Trouble Codes (DTC) Index Powertrain Control Module Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1213 Anti-Theft Number of Programmed Keys is Below Minimum PCM GO to Pinpoint Test F . B2431 Transponder Program Failure PCM VERIFY if using correct PATS key, if defective USE new key. B1342 ECU is Defective (EEFROM in PCM not working) PCM INSTALL a new PCM. REFER to Section 303-14 . B2103 Antenna Not Connected PCM GO to Pinpoint Test A . B1600 PATS Ignition Key Transponder Signal is Not Received PCM GO to Pinpoint Test B . B1601 PATS Received Incorrect Key-Code From Ignition Key Transponder PCM GO to Pinpoint Test C . B1602 PATS Received Invalid Format of Key-Code From Ignition Key Transponder PCM GO to Pinpoint Test D . B1681 PATS Transceiver Module Signal is Not Received PCM GO to Pinpoint Test E . - All Other DTCs PCM REFER to Section 419-10 .

other fuses, relays, or ecm faulty.

P1409 is an EGR code and not related to the o2 heater circuits. The PCM controls the heater circuits via drivers internal to the PCM. HIghly unlikely all drivers are bad. Most PCM's can't be tested without factory equipment and are replaced with known good ones for testing. DId this heater circuit issue start all of a sudden?

Powertrain contro module. It's your on board computer.

Hi Kelly:
If your brake switch was the problem, your brake lights would be comming on without pushing the pedal. The most common problem to cause cruise control failure is the clockspring which is a winding that contains wires that go from the cruise control switch to the PCM (computer).
You could also check the fuses. If fuse is ok there is not much more you can do unless your good with a voltmeter and can read a wiring diagram. Then you can check the power and grounds at the PCM and switch.
Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Powertrain Control Module (PCM) Hope this helps you understand ???

335 crank shaft sensor,543 (Mem) Fuel pump relay or battery power feed was open.PCM is located under the instrument panel, is the brain of the EEC system

2-Speed Torque-On-Demand (TOD) Operation
The automatic 4-wheel drive (A4WD) system is a 2-speed torque-on-demand (TOD) operation that utilizes the following components:

• Transfer case
• 4-wheel drive (4WD) control module (integral to the powertrain control module [PCM])
• Mode select switch (MSS)
• Gearmotor encoder assembly (part of the transfer case shift motor)
• Transfer case shift motor
• Shift motor sense plate (part of the gearmotor encoder assembly)

Principles of Operation
Transfer Case Shift Motor The externally mounted transfer case shift motor, located at the rear of the transfer case, turns the shift cam assembly. As the shift cam assembly turns, it positions the reduction shift fork for desired transfer case operation. An integral position sensor in the shift motor provides shift motor position information to the 4WD control module.
Mode Select Switch (MSS) The push button MSS, mounted on the instrument panel, allows the operator to select the 4x4 Auto, 4x4 High, and 4x4 Low transfer case operating modes. The indicator light, on the instrument cluster push button, will illuminate only when the 4x4 Low position is engaged.
Visual Inspection Chart Mechanical Electrical

• Axle shafts and CV joints
• Driveshaft and universal joints
• Fluid leaks
• Matching tire sizes
• Transfer case shift motor

• Battery junction box (BJB) fuses:
  • 8 (30A)
  • 17 (5A)
  • 18 (20A)
• Central junction box (CJB) fuses:
  • 12 (5A)
  • 24 (15A)
• 4x4 module (PCM)
• Wiring harness
• Gearmotor encoder contact plate
• Connector(s)
• Circuitry
• Mode indication switch (MSS)

1. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

1. If the concern is not visually evident, connect the diagnostic tool to the data link connector and select the vehicle to be tested from the diagnostic tool menu. If the diagnostic tool does not communicate with the vehicle:
   • check that the program card is correctly installed.
   • check the connections to the vehicle.
   • check the ignition switch position.

1. If the diagnostic tool still does not communicate with the vehicle, refer to the diagnostic tool operating manual.

1. Carry out the diagnostic tool data link test. If the diagnostic tool responds with:
   • CAN circuit fault; all electronic control units no response/not equipped, refer to Section 418-00 .
   • No response/not equipped for 4WD module (PCM), Go To Pinpoint Test G .
   • System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs and carry out the 4WD module (PCM) self test.

1. If the DTCs retrieved are related to the concern, go to the 4WD Control Module (PCM) Diagnostic Trouble Code (DTC) Index to continue diagnostics. 4WD Control Module (PCM) Diagnostic Trouble Code (DTC) Index
   DTC Description Source Action B1317 Battery Voltage HIGH 4WD Module (PCM) REFER to Section 414-00 . B1318 Battery Voltage LOW 4WD Module (PCM) REFER to Section 414-00 . B1319 Driver Door Ajar Circuit Failure 4WD Module (PCM) Go To Pinpoint Test M . B1322 Driver Door Ajar Circuit Short To Ground 4WD Module (PCM) Go To Pinpoint Test M . B1342 ECU is Defective 4WD Module (PCM) CLEAR the DTCs. REPEAT the 4x4 module (PCM) self test. If DTC B1342 is retrieved, INSTALL a new 4x4 module (PCM). REFER to Section 303-14 . CLEAR the DTCs. REPEAT the self test. B1483 Brake Pedal Input Circuit Failure 4WD Module (PCM) Go To Pinpoint Test M . B1485 Brake Pedal Input Short to Battery 4WD Module (PCM) Go To Pinpoint Test M . C1729 Transfer Case Unable to Transition Between 4H and 4L 4WD Module (PCM) Go To Pinpoint Test K . C1970 4WD Low Mode Switch LED Short to Battery 4WD Module (PCM) Go To Pinpoint Test K . C1971 4WD Low Mode Switch LED Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1707 Transfer Case NEUTRAL or PARK/NEUTRAL Indication Circuit 4WD Module (PCM) Go To Pinpoint Test M . P1812 Transmission 4-Wheel Drive Mode Select Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1815 Transmission 4-Wheel Drive Mode Select Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1816 Transmission NEUTRAL Safety Switch Circuit Failure 4WD Module (PCM) Go To Pinpoint Test M . P1819 Transmission NEUTRAL Safety Switch Circuit Short to Ground 4WD Module (PCM) Go To Pinpoint Test M . P1820 Transfer Case Clockwise Shift Relay Coil Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1822 Transfer Case Clockwise Shift Relay Coil Circuit Short To Battery 4WD Module (PCM) Go To Pinpoint Test K . P1824 4-Wheel Drive Clutch Relay Circuit Failure 4WD Module (PCM) Go To Pinpoint Test H . P1826 4-Wheel Drive Low Clutch Relay Short Circuit to Battery 4WD Module (PCM) Go To Pinpoint Test H . P1827 4-Wheel Drive Low Clutch Relay Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test H . P1828 Transfer Case Counterclockwise Shift Relay Coil Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1830 Transfer Case Counterclockwise Shift Relay Coil Circuit Short To Battery 4WD Module (PCM) Go To Pinpoint Test K . P1849 Transfer Case Contact Plate A Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1853 Transfer Case Contact Plate B Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1857 Transfer Case Contact Plate C Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1861 Transfer Case Contact Plate D Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1867 Transfer Case Contact Plate General Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1891 Transfer Case Contact Plate Ground Return Open Circuit 4WD Module (PCM) Go To Pinpoint Test K . U1900 CAN Communication BUS Fault 4WD Module (PCM) REFER to Section 418-00 . U2023 External Node Fault 4WD Module (PCM) REFER to Section 418-00 . U2051 One Or More Calibration Files Missing/Corrupt 4WD Module (PCM) Reprogram/Reflash the 4x4 module. REFER to Section 418-00 . - For All Other DTCs 4WD Module (PCM) REFER to Section 418-00 .
2. Your best bet mite be to take it to a qualified repair shop !