Manual Steering Column with JL4) or
Callout
Component Name
After disconnecting these components, do not move the front tires and wheels. Failure to follow these procedures may cause improper alignment of some components during installation and result in possible damage to the SIR coil.
Callout
Component Name
After disconnecting these components, do not move the front tires and wheels. Failure to follow these procedures may cause improper alignment of some components during installation and result in possible damage to the SIR coil.
Steering Wheel Position Sensor Replacement (Power Steering Column with JL4) ?
Preliminary Procedure
Remove the intermediate steering shaft. Refer to Intermediate Steering Shaft Replacement .
1
Steering Angle Sensor Adapter
2
Steering Wheel Position Sensor
Procedure
Disconnect any electrical connectors as needed.
Tip
If reusing, secure the old steering wheel position sensor before removing it for proper alignment upon reinstallation. Refer to Steering Wheel Position Sensor Centering .
Notice: Secure the steering wheel utilizing a strap to prevent rotation. Locking of the steering column will prevent damage and a possible malfunction of the SIR system. The steering wheel must be secured in position before disconnecting the following components:
?€¢
The steering column
?€¢
The intermediate shaft
?€¢
The steering gear
Preliminary Procedure
Remove the steering column. Refer to Steering Column Replacement .
1
Intermediate Steering Shaft Bolt
Procedure
Remove the steering column boot seal in order to access the intermediate steering shaft bolt.
2
Intermediate Steering Shaft Nut
Notice: Refer to Fastener Notice in the Preface section.
Tighten
47 N?·m (35 lb ft)
3
Intermediate Steering Shaft
Tip
?€¢
If necessary, scribe location marks between the intermediate steering shaft and the steering column and the intermediate steering shaft and the steering gear to mark their alignment before removing.
?€¢
If replacing the intermediate steering shaft, transfer any scribe marks from the old one to the new one.
Notice: Secure the steering wheel utilizing a strap to prevent rotation. Locking of the steering column will prevent damage and a possible malfunction of the SIR system. The steering wheel must be secured in position before disconnecting the following components:
?€¢
The steering column
?€¢
The intermediate shaft
?€¢
The steering gear
Preliminary Procedures
1
Steering Column Nut (Qty: 4)
Notice: Refer to Title not found in the Preface section.
Tighten
25 N?·m (18 lb ft)
2
Steering Column
Procedure
SOURCE: Need to replace both crankshaft position sensors 2001 Cadillac
4.6 the twocrankshaft position sensors are located on the front of the block just above and to the left of the oil filter. not hard to replace.
SOURCE: how to remove head light in 2006 dts cadillac
ok, In this New of a vehicle there are no screws holding the headlight in if you just need to replace a headlight because it is burned out. Look at the back of the light where the wires attach and you should see the wires going into what appears to be a coupling. Get a hold of that and turn. After it unlocks you can remove and replace the bulb. If you are replacing the Headlight assembly because it was damaged there are typically 2 long scews on the top front that appear to be adjsutment screws and 2 smaller ones in each side, again on top. Good Luck
SOURCE: how to change spark plug on 2006 cadillac DTS
The plugs are located by engine head. You can use a ratchet wrench and sockets to remove them. Make sure to mark the plug wires so the order doesn't get mixed up.
The check engine light comes on when there is a bad sensor, or bad circuit.
Many part stores will run an engine diagnostic code scan for free which will pinpoint exact problem that is setting of the check engine light
The light can only be shut off by the diagnostic scanner!!
SOURCE: 2006 cadillac dts - one of the headlights want
Have you changed the bulb on that side of the car? If a bulb is broken or burnt out it will not light up.
SOURCE: how do you change the headlight bulbs on a 2006
you should have to go thru under the hood to the backside of the lamp assembly. There should be either a hard plastic cap or a plastic dust cover that has the wires going thru it to the lights. If it is the hard cover (looks like a jar cap) turn it 1/4 turn counterclockwise and pull it out of the way. Take the bulb/socket out. Unclip the old one- Put the new one in. (DO NOT TOUCH THE GALSS PART OF NEW BULB). Then re-assemble
1,709 views
Usually answered in minutes!
×