How do you remove the driver side seat to replace the power seat motor? the seat is stuck al the way forward. the motor runs but the screws do not turn.

Auto Repair: How to Replace a Power Seat Motor - YouTube

? 1:44
https://www.youtube.com/watch?v=EDh-0rs5Fjo
Oct 26, 2010 - Uploaded by automdvideos
Auto Repair: How to Replace a Power Seat Motor ... 2007 - 2008 Ford Expedition/Lincoln Navigator Driver Bottom Install Video ...2003-2006 Chevy/GMC Seat Cover Install 1 of 3 - eBay Ready ...2000 Ford Explorer Front Seat Track Stuck Motor Repair - Duration: 4:39. by cubmancan 4,959 views. 4:39.
Drivers seat is dead! No power seat or heat. - TheDieselGarage.comwww.thedieselgarage.com/.../96465-drivers-seat-dead-no-power-seat-hea...Mar 22, 2010 - 2003-2005 Chevrolet Avalanche, Silverado, Suburban, Tahoe 2003-2005.... Power seat on driver side didn't work.....passenger did! Neither ...DANG electric seat ' Chevy Truck Forum ' GM Truck Clubwww.gmtruckclub.com/forum/threads/dang-electric-seat.2990/Apr 27, 2006 - 10 posts - ‎7 authors'03 Tahoe My driver seat just stopped, of corse not where I need it, the ... I have a 2003Tahoe and both heated seats are not working. ... with my seat heater on the drivers seat in my 03 Avalanche, it turns ... The driver's side on my Silverado gets way warmer than the passenger side. ... Frozen New Member.Power Seat Problems?? - Tahoe Forum - Che

Yes, if you purchase a manual set is will bolt in just the same so long as its the same model and year as they do change from year to year.

if going backward is working,and foward is not,, easy
,1st determine what is defective-so u know what to replace/repair-2 things only ,[1-switch or 2- motor under d seat]
by presing the backward swicth,, you can hear the sound of the motor running and u can see the seat is going backward...
1-now by pressing the foward switch, and you hear the motor running but not that strong like the rear ..and the seat move an inche /a little and stop,,.then u have a defect weak motor,
2- now by pressing the foward swicth and u dont hear any motor running then the switch is most likely defective
defective switch -repair- spray contact cleaner,remove cover switch,penetrate inside
defective motor-repair-remove motor replace inside carbon,,.chiepest way not to spend to much money..
i suggest even once a month,lubricate all power seat/even not powerseat/,door hinges/.trunk door/.power antenna./ .by spraying lubricating oil,. for maintanace,..you can save a lot..

You might be able to purchase the motor separately on ebay. You can remove the seat by taking out the 4 bolts that bolt the seat to the floor. Once you have the seat removed, disconnect the wiring harness from the motor assembly and detach the motor from the spiral gear assembly. You can then manually screw the seat to your desired position and leave it there if you are the only driver. Good luck! Any questions, feel free to ask.

Power seat movement is controlled by numerous small motors underneath the seat.

Front and back movement is often actuated through a motor on one side that connect to a rod (with some type of gear on the end of it) that runs to the other side. This rod can get out of position, or possibly something can go wrong in the gear.

You'll likely have to remove the seat to diagnose the problem.

This is not necessary...as many have stated...use a hammer with switch in reverse position. Hammer the seat back...it will catch...

There are plastic gears connecting the track to the seat assembly. Whne one of these strip the seat will only work or move to one side. Infiniti does not sell a simple fix. You are looking at buying an entire seat assembly complete with the module for all the electronics. It will be at a cost of around $950 - $1000. Once that is in, Infiniti must program the seat to the brain of the car, only then can you reset your memory settings.

I just had the same problem. When the seat is powered all the forward, one of the worm drives reached the end of its travel and jammed against the threaded block that it passes through. To fix this the seat has to be unbolted and tipped back. There are four tiny 6mm bolts that hold the motor plate in. Remove these and the motor will come out. The worm drive is bolted in at one end and has a set pin at the other. Remove the worm drive and use a couple of vice grips or equivalent to loosen the threaded block from the worm drive.

Take apart the drive box in front of seat track, on both sides with an allen wrench. You can then push the seat to get at the bolts to remove it. My trolley drive motor had bad brushes. I am now looking to replace the motor, if I can find the replacement.

maybe you got pennies money stuck in the track if not you got 1 motor for that the motor goes in a assembly in there you have 2 cable a left and a right lock under the seat you probably got the right cale disconnect sometime there stuff that push under the seat and push that cable off if its that just push the cable back in let me know and please if you can take the time to rate this thank you pierre
p.s when you try to put the cable back in dont force to mush
PIERRE