Where is #2 cylinder on 2000 jaguar s type 4.0?And what is code p0302

All codes are OBD2 on free online , try it.
https://www.fixdapp.com/blog/p0302
https://www.fixdapp.com/blog/p0335
https://www.yourmechanic.com/article/p0202-obd-ii-trouble-code-injector-circuit-malfunction-cylinder-2-by-spencer-clayton

P0300 = Random/multiple cylinder(s) - misfire detected.
P0302 = Cylinder 2 - misfire detected.
P0304 = Cylinder 4 - misfire detected.
P0306 = Cylinder 6 - misfire detected.

A misfire can be caused by a few things. The most common causes are usually spark supply or fuel supply. Get BOTH of these checked.
All the misfires are on the same side of the engine so I would suspect a fuel rail or an injector issue on that side of the engine.

The engine light is on because have a fault code P0304, it means Cylinder 4 Misfire Detected
________________
Can Clip Renault

All fault codes can be checked out at http://www.bluejag.co.uk but here are the results for some of yours. You can ignor P1111. Looks like a faulty plug or coil pack cylinder 2

Fault Code:- P1314 Indicates a Power-train fault


The fault is generally due to a problem in the Ignition or Misfire area


Fault Description: Misfire rate catalyst damage -bank 2 NOTE: This DTC will flag only when accompanied by an individual cylinder misfire DTC: P0300 - P0306

Action of ECM:- ECM Default:- Maximum engine speed reduced


After clearing the DTC, complete the Misfire monitor drive cycle
Check for a reoccurrence of fault DTC.

Possible Fault:- Cylinder compression low Worn camshaft / broken valve spring(s) Fuel delivery pressure (low / high) Fuel injector(s) restricted / leaking Fuel injector(s) continuously open Fuel contamination Fuel injector circuit fault(s) (Injector DTCs also flagged) Spark plug failure / fouled / incorrect gap ECM to ignition coil primary circuit fault (Cylinder misfire detected DTC also flagged) Ignition coil failure
Fault Code:- P1316 Indicates a Power-train fault


The fault is generally due to a problem in the Ignition or Misfire area


Fault Description: Misfire excess emission NOTE: This DTC will flag only when accompanied by an individual cylinder misfire DTC: P0300 - P0306

Action of ECM:- none


After clearing the DTC, complete the Misfire monitor drive cycle
Check for a reoccurrence of fault DTC.

Possible Fault:- Cylinder compression low Worn camshaft / broken valve spring(s) Fuel delivery pressure (low / high) Fuel injector(s) restricted / leaking Fuel injector(s) continuously open Fuel contamination Fuel injector circuit fault(s) (Injector DTCs also flagged) Spark plug failure / fouled / incorrect gap ECM to ignition coil primary circuit fault (Cylinder misfire detected DTC also flagged) Ignition coil failure

Fault Code:-
P0302 Indicates a Power-train fault


The fault is generally due to a problem in the Ignition or Misfire area


Fault Description: Misfire detected ?€" cylinder 2

Action of ECM:- none


After clearing the DTC, complete the Misfire monitor drive cycle
Check for a reoccurrence of fault DTC.

Possible Fault:- Refer to P0300 Possible Causes

P303 = Cylinder 3 misfire P0734= Gear 4 incorrect ratio 0745= Pressure Control Solenoid A
Not sure if you just wanted to know what the codes were, or how to fix them hope this helps

Bad coil on # 2 (PO-302)

I would check that spark plug, and have that coil checked or replaced. Also check for any vacuum hose leaks in the area of the cylinder.

THE P0302 is misfire cyclinder 2,4,and 5
The P1313 P1316 is Cyclinder compressor low, Worn camshaft/ broken valve springs. Fuel injector contamination, Spark plug failure/ incorrect gap. Iginition coil failure.
P0778 is 2/4 Brake prssure solenoid failure

HOPE THIS CAN HELP.

P0302= # 2 cylinder misfire,
check plug,plug wire,injector or coil

2000 4.0 jaguar s type cylinder firing diagram:
FRONT OF CAR
5 1
6 2
7 3
8 4