How do you reset security? the car will start and run for 1 second and shut off.

Question edited for clarity, add MAKER.
Question moved to model category.

Number 1 tip, NEVER disconnect a battery. Always keep voltage to the ECM and Anti-Theft Immobilizer. You can use two wires, another battery or jump leads attached to the connectors. Even an MN1500 battery is enough power for 10 minutes.

There is normally lots online regarding setting the security system, but I only find this

https://www.cargurus.com/Cars/Discussion-t24487_ds612242

https://www.google.com/search?q=2010+Volvo+XC60+reset+security+system

..

Vehicles equipped with the PASS-KEY or VATS anti-theft system usually require the system be reset whenever the battery is drained or replaced. Follow this procedure.
Step 1 - Attempt to start the vehicle. It will crank, but not run. The security light will be flashing on and off. Leave the key in the run/on position for exactly 10 minutes, then the security light will stay solid or go off.
Step 2 - Turn the key to the 'off' position for 10 seconds. Attempt to start the vehicle. Some vehicles will run at this point, although many will require you repeat repeat Step 1 two more times. Make sure turn the key to the 'off' position for 10 seconds before each 10 minute cycle.
Step 3 - The vehicle is now ready to relearn the proper code. Turn the key 'off' for 10 seconds and then 'crank' the vehicle. It should be running now. The security light might stay on solid for several minutes afterwards, depending on your system.

Check the security locks, if the truck still thinks its locked, it will let itself start and run momentarily then shut itself off, there's a way to reset it but I don't remember how right now

Do it three times in a row.

1. Perform a security system relearn.
2. Let the vehicle sit for more than 10 minutes with the key off.
3. Attempt to start the engine, leave the key in the run position monitoring the security system indicator.
4. After 10 minutes, the security indicator will change state.
5. Turn the key off and wait 10 seconds.
6. Attempt to start the engine. If the engine stalls, wait another 10 minutes with the key on.
7. After the second 10 minute timer has expired, turn the key off for 10 seconds.
8. Attempt to start the engine. If the engine stalls, wait another 10 minutes with the key on.
9. After the 3rd 10 minute timer has expired, shut the key off for 10 seconds.
10. The security system will relearn on the 4th starting attempt and the engine should start and run.

Here is a link about the security problem

http://vatspasslockpasskeysecurityhelp.yolasite.com/

1. Perform a security system relearn.

2. Let the vehicle sit for more than 10 minutes with the key off.

3. Attempt to start the engine, leave the key in the run position monitoring the security system indicator.

4. After 10 minutes, the security indicator will change state.

5. Turn the key off and wait 10 seconds.

6. Attempt to start the engine. If the engine stalls, wait another 10 minutes with the key on.

7. After the second 10 minute timer has expired, turn the key off for 10 seconds.

8. Attempt to start the engine. If the engine stalls, wait another 10 minutes with the key on.

9. After the 3rd 10 minute timer has expired, shut the key off for 10 seconds.

10. The security system will relearn on the 4th starting attempt and the engine should start and run.

If this doesnt work, and you are having STARTING issues, go to this link.

http://vatspasslockpasskeysecurityhelp.yolasite.com/

Hello: Will try to give you instructions: Attempt to start car, leave key on (security light flashing) let set for 10 minutes, After 10 minutes security light out. Turn key off for ten seconds, turn key on, let set for 10 minutes, turn key off for 10 seconds. turn key back on let set 10 minutes, turn key off for ten seconds, the engine should now start and stay running.

does it start at all, or does it run for about 1 second and shut off? if the latter, then it's the passlock system, and he could have a defective key or security module. the keys have a predetermined resistance value which activates the passlock system to prevent hotwiring. If it is the passlock system, then sometimes you have to wait 15-20 mins for it to reset before starting the engine.

Sounds like your security system is shutting the car down. You should be able to leave the key on for 15 minutes and it will reset itself. Make sure you are using factory keys, and they are in good condition.

The problem is the new PCM you installed does not have the correct VIN number of your car.
You may be able to relearn the VIN using the preceedure below, however, there is no gaurentee it will work. You may have to have a dealer reset the VIN for you by way of a scan tool.

1) Instert key into ignition and rotate to run position (do not try to start engine)
2) Leave the key in the run position for 10 minutes until security light stops flashing.
3) Turn ignition key to off position for 10 seconds ( no more, no less)
4) Turn ignition to run position again for 10 minutes until security light stops flashing and repeat step 3 and 4 for (1) more cycle.

The process is a security verification step for the VTD system. ( Vehicle Theft Deterent)

Give it a try, let me know.
Regards,

if it runs for about 2 seconds and shuts off everytime I would change the fuel filter