Question about 1994 Toyota Corolla

1 Answer

Piston stuck on slave cylinder

Piston stuck on master cylinder

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 14,585 Answers

They both need replaced. I never do just one. If you have to pull the transmission to get the slave out. You might as well replace the clutch package and have the flywheel turn.

Posted on Aug 01, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Installed new caliber and rotor caliber still locking up, is master cylinder bad?


when you are done with a brake job it is always important to make sure you can slide the caliper both inward and outward by hand to ensure that there is no sticking, (that is with the pads in place and caliper piston completely depressed into the caliper) it is not rare to find that a piston that is very hard to depress back in the caliper is due to deterioration of the inner lining of the brake hose, if you have problems pushing the piston back into place most likely this is your problem. I have strong hands and is most vehicles I can push the piston back into the caliper by hand.

Mar 15, 2015 | 1998 Dodge Neon

2 Answers

Clutch feels loose,no pressure. gears are stuck, shifter wont moveis it the clutch adjustment?


The Clutch Master Cylinder or the Clutch Slave Cylinder has a leak. From under the dashboard, located the Clutch Master Cyliner Boot and pry one side open. If hydraulic fluid drips out, the piston seal(s) in the cylinder are worn. You'll need to replace the cylinder.

Dec 27, 2014 | 2003 Chrysler PT Cruiser

1 Answer

I have 1988 cadillac allante the lh rear brake line rusted through know the brakes wont bleed no mater what i do even tried staring at abs pump and master evev replace some calipers


You may need to go to the master cylinder and release the piston for the rear brakes circuit. It is best to get a manual for this operation as it may require the removal of a switch in the master cylinder or a threaded pin between the pistons. There are two pistons that are spring actuated and when one circuit loose pressure a piston is stuck in the wrong position.

Oct 04, 2014 | 1988 Cadillac Allante

3 Answers

Bled my Clutch Slave Cylinder Wrong?


it shounds as though your master cylinder might not be pumping any fluid.

Aug 03, 2014 | 2008 Ford Fusion 2.3

1 Answer

Just changed the slave cylinder and master cylinder bled it but still no clutch


when bleeding did you press pedal really softly at every press or did you press it as if changing gear ? if as changing gear i expect you have pushed the cylinder piston past the end stop , you will have to dismantle cylinder and manually pull the piston back and make sure the seal is on the end , if not it will be stuck up the cylinder , carefully pry out and refit to piston , put a tiny amount of vaseline around the seal before reassembly and bleed again but press pedal very slowly , keep me posted if you wish

Jul 15, 2014 | 2004 Dodge Dakota

1 Answer

Broken clutch pedal replaced and no stuck


replace the master cylinder as there are burrs and grooves in the cylinder that is jamming the piston movement.

Mar 02, 2014 | Kia Cars & Trucks

1 Answer

Clutch troublers


possible causes are,fluid leaking from the master cylinder, trapped air to the clutch system.master cylinder piston stuck.

Dec 26, 2010 | 1987 Toyota Corolla 2 Door

1 Answer

I have a brake binding problem i changed the master cylinder twice,change the flexible brake lines and changed the seals of the front calipers and cleaned the pistons of the calipers too.


If you have a frozen caliper, (rusty piston stuck inside calipers cylinder), then you have to options:
Replace the caliper piston and sea,l with a new one, or replace all thing i.e, the caliper. Hope will help.

Sep 07, 2010 | 1996 Toyota Corolla

2 Answers

The clutch is stuck to the floor bord and i cant shift


you may have a faulty clutch master cylinder or faulty clutch slave cylinder- leaking clutch fluid. most of the time both are replaced at the same time which should be recomended by your mechanic, the bolts to the master cylinder are very hard to get to and require the right tool.
you should be able to move car forward by selecting 1st then cranking engine till it starts, gear changes while driving are hard but not impossible. i recommend a tow truck to a local repairer.

Dec 22, 2009 | 1995 Isuzu Rodeo

Not finding what you are looking for?
1994 Toyota Corolla Logo

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...