Malfunction upon starting car. Keys will not come out

I deleted the AI Bot answer and have modified it below. In cases like this though, the problem can only be diagnosed electronically using an auto electrician and a pro grade scan tool computer.

https://www.google.com/search?q=mobile+auto+electrician+near+me

1. Faulty key chip: One possibility is that your key chip is faulty or damaged. Over time, keys can become damaged, which can cause problems with the ignition switch. You may want to try using a spare key to see if the problem persists.
2. Battery issues: Another possibility is that your truck's battery is weak or failing. If the battery is not providing enough power to the ignition switch (12.4 volts minimum), it may cause the system to malfunction. You may want to have the battery checked and replaced if necessary or at lease clean the terminals inside and out with a wire brush.
3. Ignition switch transponder problems: The ignition switch may be faulty, which can cause intermittent starting problems. If the ignition switch is failing, it may not be able to recognize the key properly, leading to starting issues.
4. Wiring or electrical problems: There may be issues with the wiring or electrical system that are causing the starting problems. Faulty wiring or connections can cause the system to malfunction, leading to issues with starting the truck.

..

Sounds like the immobilizer (SKIS) has been activated. To disable it, you would need to plug in a Chrysler scanner (DRB-III) with current software and input the appropriate PIN number (available only from Chrysler upon proof of ownership. Your best option at this point is to contact your local dealer

that is a 12vdc power problem.
the sensors are failing , many do to lost power. (12vdc electrical distribution power)
so use a voltemeter, i bet even at he cig lighter port the voltage drops
below 13.3v running, way below. infact.
are your battery terminals clean,
is the rested voltage at the battery terms 12.6v (keys in pocket)
no? then the battery is being discharged,

hello, i would suggest trying to replace your solinoied realy, try starting again, when it continues to run on pull the realay insted of disconecting the battery if this stops it, you may have bin isued a latching realay type, from your parts supplyer.
good luck, let me know how you faired

Programming
When
Key(s) added or replaced. System malfunction.
How
Obtain all keys fitted with remote control. Turn ignition switch from position 0 to position II 4 times within 6 seconds. Turn ignition switch to position 0. The system will emit an acoustic signal to indicate start of programming mode. Programming mode activated for 10 seconds proceed as follows: Press and hold lock, unlock or boot release button Fig. 1 [1], [2] or [3]. Wait for acoustic signal (indicates correct programming). Repeat above procedure within 10 seconds to program remaining keys. To exit programming mode: Turn ignition switch to position III or wait 10 seconds. Keys can also be programmed using diagnostic equipment.
NOTE: A maximum of 4 keys can be programmed

System operation
System arms 5 seconds after switching ignition OFF. Switch ignition ON. Ensure clock LED illuminates for 3-5 seconds. If LED flashes rapidly at regular intervals for approximately 1 minute, then flashes at irregular intervals: Key code not recognised. Remove key and try again.
Programming
When
System malfunction: LED illuminates for 1 minute, then flashes at irregular intervals. Key(s) added or replaced.
NOTE: Replacement keys MUST have blue mark. Keys with red mark are NOT compatible with this system.
How
NOTE: Programming method using vehicle keys can be deactivated using diagnostic equipment.
Obtain 2 programmed keys (A and B). Insert key A into ignition switch. Turn ignition switch to position II. Wait 1 second. Switch ignition OFF. Remove key A. Insert key B into ignition switch within 5 seconds. Turn ignition switch to position II. Wait 1 second. Switch ignition OFF. Remove key B. Within 10 seconds: Insert key to be programmed into ignition switch. Turn ignition switch to position II. Wait 4 seconds. Switch ignition OFF. Wait 5 seconds. Start engine. If engine does not start and clock LED flashes: Switch ignition ON. Wait at least 20 seconds. Switch ignition OFF. Repeat programming procedure. Repeat above procedure to program remaining keys. Keys can also be programmed using diagnostic equipment

rollover switch is located in rear area behind left panel

i have a 05 saab 93 stupidly i left keys in ignition overnight today it reads on sid steering lock malfunction i now cannot start car help

Don't remember posting anything to you, But, regardless, first a question... Can you turn off the flashers
at the switch?? Do you have an alarm system? (if so, possible malfunction there) Otherwise, check battery grounds and connections (other ends of cables from battery) if you have one, check start relay&or starter solenoid!

TRY TO START THE VEHICLE IN NEUTRAL IF IT STARTS YOUR NEUTRAL SAFETY SWITCH HAS MALFUNCTION, OTHERWISE ITS MORE THAN LIKELY THE STARTER, TRY BOTH KEYS ,THE COMPUTER COULD HAVE LOST THE CODE IN THE KEY