Question about Dodge Cars & Trucks

1 Answer

Location of cam and crank sensor on 97 Dodge neon

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 98 Answers

Enter 97 dodge neon crank sensor in you tube. Videos there I just found. Good luck.

Posted on Jun 12, 2015

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 3 Answers

SOURCE: Cam Shaft Sensor Problems

Had the same problem before on my 04 Neon SXT...camshaft sensor is on left side of engine block, take out the battery and to the left of it (face car) is the camshaft position sensor. To change it you'll have to move a few hoses but its plan to see there on the left side of the engine...pretty easy remove and replace. Fixed my problem of car not going above 2k RPM when i replaced the sensor.

Posted on Dec 29, 2008

Anonymous

  • 512 Answers

SOURCE: knock sensor location on a 2004 dodge neon

knock sensor is located under the intake manifold in front of the starter. what codes did you have?

Posted on Jan 07, 2009

Anonymous

  • 19 Answers

SOURCE: 2005 dodge noen cam sensor

I own a 2002 neon sxt and recently had to replace the cam sensor it should be in the same place.
look on the right side of the motor you should see it. it'll have a small wire harness that clips in the top and its fastend with 4 bolts. Oh and take the battery out before you do it it makes it a lot easier.

Hope this helps.

Posted on Feb 25, 2009

Robert Debison

  • 412 Answers

SOURCE: 97 dodge neon died replaced parts and still no spark HELP.

YOU NEED TO CHECK DARK GREEN/ORANGE WIRE AT IGNITION COIL WHEN CRANKING ENGINE FOR POWER..IF NO POWER,SHUTDOWN RELAY IS NOT BEING ENERGIZED..THIS ENGINE ALSO HAS CAMSHAFT POSITION SENSOR ON END OF CYLINDER HEAD..ENGINE CONTROLLER NEEDS CAM AND CRANK SIGNALS TO ENERGIZE THE SHUTDOWN RELAY..UNPLUG CRANK SENSOR AND CHECK VOLTAGE ON ORANGE WIRE..SHOULD HAVE APPROX 8V..IF NOT..UNPLUG CAM SENSOR AND SEE IF 8V SUPPLY RETURNS..IF NO POWER TRY UNPLUGGING VEHICLE SPEED SENSOR LOCATED IN TRANS HOUSING WHERE RIGHT SIDE AXLE COMES OUT OF TRANS..IF 8V RETURNS..THE SPEED SENSOR IS SHORTED INTERNALLY..THESE 3 SENSORS SHARE THE SAME 8V SUPPLY CIRCUIT..WITH SPEED SENSOR UNPLUGGED,PLUG CRANK SENSOR BACK IN AND TRY TO START ENGINE..HAVE SEEN THIS SAME PROBLEM AT WORK RECENTLY

Posted on Jul 19, 2009

csmock132

Clint Smock

  • 4669 Answers

SOURCE: 2001 dodge 3500 van cam position sensor location

Crank sensor is in the bell housing of the transmission. Cam sensor is in the distributor.

Posted on Jul 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of cranksensor


Hi Margaret, The link below is a youtube video showing how to replace a crank sensor on a 1997 dodge neon, I know it's not a 1996 BUT motor should be the same, I hope this helps....... CHEERS..
1997 Dodge Neon no start crank sensor problems

Apr 29, 2016 | 1996 Dodge Neon

2 Answers

My 2001 dodge neon cranked without the cam sensor connected. what's wrong with this picture?


Changing the Cam Position Sensor on Dodge Neon ...

? 10:33
https://www.youtube.com/watch?v=ciCPQ0kVAQY
Dec 21, 2012 - Uploaded by VeeTheAmazingGreek
... had to change out the cam position sensor on my 2001 Dodge Neon. ... 1997 Dodge Neon no start, crank sensor problems - Duration: 26:53.

Dodge Neon Questions - It will turn over but has no spark ...

www.cargurus.com > Questions > Dodge > Neon

CarGurusAug 9, 2015 - I did have a neon while ago and image crank sensor was bad ... my 1999dodge neon has no spark it will turn over but not fire i have changed the crank sensorcoil ... I have a 2001 Dodge Neon 2.0 with 140,000 kms on it.

Dodge Neon Questions - 2001 Dodge Neon will turn over ...

www.cargurus.com > Questions > Dodge > Neon

CarGurusJan 7, 2013 - I have a 2001 Dodge Neon 2.0 with 140000 kms o... ... went about a month before this recent problem, fixed that with no problem now this. ... firing. you said you replaced the cam sensor, did you do the crank sensor as well? ... My 1996Dodge Neon won't stay running whenever I take my foot off of the gas.

Starting Issues and Trouble Code Due to Defective Cam ...

repairpal.com > Problems > Dodge > Neon

Feb 05, 2016 | 2001 Dodge Neon

1 Answer

Location of crank sensor for 97 dodge neon


Don't know your engine, but most are near the crank front pulley or under it.

Jun 11, 2015 | 1997 Dodge Neon

1 Answer

Problem with 2003 Dodge Neon My 2003 dodge neon


run fault codes and check for cam/crank position sensors fault. Check that the cam is turning as it may have broken a timing belt.

Oct 16, 2013 | 2003 Dodge Neon

2 Answers

Cam position sensor location find the location on engine


Mounted on the backside of the cylinder head.

Feb 03, 2010 | 2004 Dodge Neon

1 Answer

2000 neon cam sensor location?


2000 dodge neon cranks but wont start, but if i unplug the cam sensor it will run for a second

Oct 19, 2009 | 2002 Dodge Neon

2 Answers

97 dodge neon died replaced parts and still no spark HELP.


YOU NEED TO CHECK DARK GREEN/ORANGE WIRE AT IGNITION COIL WHEN CRANKING ENGINE FOR POWER..IF NO POWER,SHUTDOWN RELAY IS NOT BEING ENERGIZED..THIS ENGINE ALSO HAS CAMSHAFT POSITION SENSOR ON END OF CYLINDER HEAD..ENGINE CONTROLLER NEEDS CAM AND CRANK SIGNALS TO ENERGIZE THE SHUTDOWN RELAY..UNPLUG CRANK SENSOR AND CHECK VOLTAGE ON ORANGE WIRE..SHOULD HAVE APPROX 8V..IF NOT..UNPLUG CAM SENSOR AND SEE IF 8V SUPPLY RETURNS..IF NO POWER TRY UNPLUGGING VEHICLE SPEED SENSOR LOCATED IN TRANS HOUSING WHERE RIGHT SIDE AXLE COMES OUT OF TRANS..IF 8V RETURNS..THE SPEED SENSOR IS SHORTED INTERNALLY..THESE 3 SENSORS SHARE THE SAME 8V SUPPLY CIRCUIT..WITH SPEED SENSOR UNPLUGGED,PLUG CRANK SENSOR BACK IN AND TRY TO START ENGINE..HAVE SEEN THIS SAME PROBLEM AT WORK RECENTLY

Jul 18, 2009 | 1997 Dodge Neon

1 Answer

99 Neon sohc keeps wipping the cam and crank sensors


Shake or gentle tug on the wiring harness and try starting the engine! I found that my problem was with the cam sensor wiring harness

Oct 07, 2008 | 1999 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...