What would cause the low beam headlight not to work when all other lights work?

PAWEL IS A BOT. HE POSTS GENERIC ANSWERS. AND OVERLAYS NAME OF YOUR CAR. 82 GENRIC ANSWERS HIM
AND LIES ABOUT IGN SWITCH.
NOW YOUR CAR.! FACTS, ONLY, 1 CAR
LEARN TO USE THE DMM , CORRECTLY;
HEAD LAMPS ON.(SWITCH) NO KEY IS NEEDED FOR HL.
IS DRIVER LEFT OR RIGHT,? IN USA LEFT.
IS HIGH AND LOW BEAMS DEAD LEFT? No TOLD AT ALL.
PUT METER BLACK LEAD TO THE BATTERY NEG LUG
THEN PROBE RED TO ALL WIRES OF DEAD LAMP 1 BY 1.
12VDC IS GOOD 0 BAD
IF LAMP GROUND PIN READS 12VDC <<< GROUND FAILS.

LEFT LAMP USES GROUND LUG G101. IF R

CAR HAS DRL. SO DRL AND MANUAL LAMPS FAIL
HIGH , LOW , AND FLASH HIGH>? NOT TOLD
DOES ENGINE RUN? OMG NOT TOLD.
THIS CAR RUN HL RELAYS BY BCM CONTROLLER BRAIN


FUSE ARE ON THE OUTPUT OF ALL HL RELAYS
SO IF ALL FUSES INPUT(TOP) ARE DEAD,THAT MEANS
BCM IS FAILING. OR THE SWITCH TO IT.
OR FUSES BLOW TO BCM
WE SCAN THE PCM/BCM TO SE WHY.


HEAD LAMPS ON THE 4 FUSES ALL 4 RIGHT SIDE ARE
12VDC, IF NOT BCM IS MESSED UP, OR RELAY DEAD.
HE LOW BEAM RELAY RUNS BOTH SIDE
SAME WITH BEAM. A RELAY FOR IT.
DRL HOT ONLY IN DRL MODE.
DRL; HAS A SUN SENSOR (AUTO MODE)


BOTTOM HERE IS HEAD LAMPS.SIDE.

HEAD LAMPS ON USA WORK EVEN KEYOFF
SO DOES BCM TO DO THAT, MAIN BATTERY NOT DEAD

Check the wiring on that light. Also check the bulb with a couple of wires to the battery, or swap the bulb left to right to make sure the new bulb is okay.

It could be driving lights mode instead of low beam. Check connections.

I would check for the groundwire continuity

Driver side - dim low beams and no hi beam - Subaru Outback ...

www.subaruoutback.org > ... > General > Electrical & Electronics

Oct 11, 2014 - Hi everyone, My drivers side headlights are dim on low, (car has separate bulbs ... When the headlight switch is turned ON, but for low beams, ...

Driver-side Low beam Not Working (electrical issue not bulb ...

www.hummer4x4offroad.com/.../showthread.php?...Driver-side-Low-be...

Mar 12, 2015 - 10 posts - ‎4 authors
The high beam continues to work on both sides...I pulled the Driverside headlamp fuse and then both left and right beams lit up but very dim.

High beams ok, but not low beam - one side only - TDIClub Forums

forums.tdiclub.com > ... > VW MKIV-A4 TDIs (VE and PD)

Jan 23, 2014 - My driver's side lights are working fine - high and low beams. ... But it definitely looks like the big lamp on the driver's side gets brighter when ..... Drivers side headlight is very dim on low beam and goes out when on high beam ...

Dim driver's side headlight (low & high beam) - GrandAmGT.com Forum

www.grandamgt.com > ... > Technical Q&A

Dec 11, 2002 - 6 posts - ‎4 authors

check low beam fuse when switched on if it has voltage registering across the fuse ,if there is voltage across the low beam RHS fuse then it is possibly a pinched wire from the headlight running back towards inside of the car

When either the high or low beam light is out in either side, DRL (daytime running lights) indicator will come on. When one bulb goes out, that's a clue the opposite bulb will burn out soon, so its best to replace both bulbs. If it was a fuse issue, both left and right side would be out. If driver side is OK but passenger side is not, then its a bulb issue. A 2006 Honda civic takes 9006 (HB4) low beam bulbs and 9005 (HB3) high beam bulbs. Cheapest is online from Walmart site-2-store. After procuring, wear latex, vinyl, or ANY gloves to keep your (corrosive) oil skin from coming in contact with headlight glass bulbs. Your skin oil will chemically react and cause shorter life span on glass bulbs. Instruction don't tell you this, so you handle with your hands, then need to replace bulbs 3 years later instead of 5 years (or more) in the future. With gloves on, pop the hood and look behind each headlight. Turn counter clockwise to unlock headlight bulb holders. Its a quarter to half turn to unlock bulb holder lock. Replace one bulb at a time so you don't confuse high beam from low beam. The wire has a tab you need to lift to pull out & disconnect wire connector. You might need a slim narrow-**** (NOT phillips) screwdriver to lift the tab; or use your house key. Snap the wire connector to the new bulb, then twist into headlight housing to secure bulb holders, then move on to the next bulb to repeat the procedure. Pict below, 9005 high beam is on the left, 9006 low beam is on the right. Handle by grasping the plastic base, not the glass bulbs. The raised potrusion on the bottom center is where the tab locks onto wire connector. Replace all 4 bulbs now, but in the future, its likely the low beam will wear out before the high beam. In the future, replace only the pair, not all 4. The factory installs inferior bulbs that go out sooner, hoping you'll take to dealership and they ******** you with higher parts-n-labor fees. As opposed to Walmart online site-2-store, it would cost you AT LEAST triple in parts & labor from dealership to replace all 4 headlight bulbs :-(

the high beams work fine and power goes to the only when vehicle is on when it is off no power gets to the low beam side of the right headlight. ????????

Power for the headlights on the Left side (High and low beam.) comes from the same fuse... The ORANGE wire and the ORANGE/BLACK are the same, they connect in the harness. If you only lack the 12v to make the light work connect them at the headlight assembly.

If your low beam also lacks ground the Left low beam ground is shared with the right low beam ground... Run a wire from left low beam DARK BLUE to right low beam DARK BLUE/WHITE.

If its not working now then your cursed, seek a witch doctor.

you say you replaced both bulbs, you mean right and left or both the high beam and the low beam on left side?could be a bad ground for the left headlight. there should be some ground wires there near the headlight, LF corner under hood. without a wiring diagram here at home,I am not much help.

faulty light switch or light control module