WHERE IS THE ECM LOCATED - 2002 Buick Century

It is in the engine bay next to the radiator cap. There are very few reasons where you ever need to go near it.

Where is the ECM located on a 2001 Jeep Cherokee Sport

Jeep Cherokee Forum https://www.cherokeeforum.com > where-ecm-located...

Feb 4, 2018 · 16 posts · 3 authors
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here - Where is the ECM located on a 2001 Jeep Cherokee Sport ?
where is my pcm located? HELP! please
Aug 19, 2014
Where is the ECM located ? - Jeep Cherokee Forum
Oct 1, 2015
???replacing an XJ computer??? - Jeep Cherokee Forum
Apr 12, 2017
Replacing the PCM - Jeep Cherokee Forum
Dec 6, 2009
More results from www.cherokeeforum.com

More here

https://www.google.com/search?q=2001+jeep+cherokee+sport+ecm+location

..

The ECM, or engine control module, on a 2008 oz trike chopper 2 is typically located under the seat or in the engine compartment.
To locate the ECM on your trike, follow these steps:

1. Locate the seat of the trike. The ECM is often located underneath the seat or in a compartment built into the seat itself.
2. If the ECM is not located under the seat, it may be located in the engine compartment. The engine compartment is typically located at the front of the trike, behind the front wheel.
3. Look for a box-like component with wires connected to it. The ECM is typically a small, rectangular component with several wires connected to it. It may be labeled with the initials "ECM" or "ECU" (engine control unit).
4. If you are unable to locate the ECM using the above steps, consult the owner's manual for your specific model of trike for more information.

Note: The location of the ECM may vary depending on the specific model and configuration of your trike. If you are unsure of where to find the ECM on your trike, it is recommended that you contact a qualified mechanic or the manufacturer for assistance.

The computer near the battery is the ecm. It will have three connectors going to it.

The ECM in the 2001 Daewoo Lanos is located under the front passenger seat and the ECU is located on the passenger side firewall.

ECM is located behind the glove box. I hope this helps

REMOVAL & INSTALLATION

Print

OPERATION

When the term Electronic Control Module (ECM) is used in this guide it will refer to the engine control computer regardless that it may be a Vehicle Control Module (VCM), Powertrain Control Module (PCM) or Engine Control Module (ECM).
The Electronic Control Module (ECM) is required to maintain the exhaust emissions at acceptable levels. The module is a small, solid state computer which receives signals from many sources and sensors; it uses these data to make judgments about operating conditions and then control output signals to the fuel and emission systems to match the current requirements.
Engines coupled to electronically controlled transmissions employ a Powertrain Control Module (PCM) or Vehicle Control Module (VCM) to oversee both engine and transmission operation. The integrated functions of engine and transmission control allow accurate gear selection and improved fuel economy.
In the event of an ECM failure, the system will default to a pre-programmed set of values. These are compromise values which allow the engine to operate, although at a reduced efficiency. This is variously known as the default, limp-in or back-up mode. Driveability is almost always affected when the ECM enters this mode.

REMOVAL & INSTALLATION

See Figures 1 and 2

Fig. Fig. 1: ECM mounting scheme-except 1996 models

Fig. Fig. 2: ECM mounting scheme-1996 models
The ECM is located in the passenger side footwell in the kick panel up to 1996. In 1996, the ECM is located in the engine compartment next to the battery.

1. Disconnect the negative battery cable.
2. Disengage the connectors from the ECM.
3. Remove the spring retainer off and over the rail of the ECM on vehicles except 1996.
4. Slide the ECM out of the bracket at an angle.
5. Remove the ECM.

To install:

1. Install the ECM into the bracket.
2. Install the spring retainer (except 1996) and plug in the electrical connectors.
3. Connect the negative battery cable.

The ECM on a 1992 S10 and S10 Blazer is located below the glove box.

The ECM located behind the glove compartment door, remove the glove compartment you will see the ECM.

hope this can help

On the 96 Se the computer should be located on the drivers side, behind the fuse panel. Remove the side interior panel, then loosen the bolts that hold the fuse panel so that you can get to the plastic box with a lot of wires hooked up to it. They are snap-fit connectors like the rest of them.

ECM fuese are located in the fusebox in the engine compartment-left sidefacing the vehicle.