How do you replace the rear wheel hub on a 2003 Kia sedona. All I can find is directions on front not back.

Fix It Right! - Front Hub Bearing Replacement - YouTube

? 14:26
https://www.youtube.com/watch?v=l0LCkycUcqM
Sep 7, 2011 - Uploaded by OneSourceAutomotive
Front Hub Bearing Replacement (S1E3) Demonstrated on a 2004Kia Sedona FWD. ... on a front-wheel ...

Kia Sportage wheel bearing replacement - YouTube

? 4:10
https://www.youtube.com/watch?v=wa6NREeozbE
Apr 3, 2014 - Uploaded by Jo Daddy's Garage
I did a quick replacement of a bad rear wheel bearing/hub on aKia ... How to install front struts on a Kia ...

Yes u can do it your self and yes on drive is ok u will b able to do it Fred hi
with drifts most will just come of as u dismantle it the only one that is hard to do is the rear one on stub axle and some times the carrier in hub just go steady and work ur way around knocking them of keeping square as they come of putting back u will need a deep scoket the same size as carrier not on bearing its self then build back up come back to me if u have any probs

Disassembly 1. Remove oil seal from front wheel hub. 2. Remove front wheel hub assembly with suitable tool.

3. Remove retaining ring. If the bearing inner race remains on wheel hub, grind a section of inner race until approximately 0.020 in (0.5 mm) remains. Remove race with a chisel.

4. Remove wheel bearing with suitable tool.

• Do not remove dust cover unless necessary. • Do not reuse dust cover if removed. 5. Mark relative positions of dust cover and knuckle for proper reassembly. 6. Remove dust cover with a chisel.

• Do not remove wheel hub bolt unless necessary. • Do not reuse wheel hub bolt if removed. 7. Remove wheel hub bolt with a press.

Assembly 1. Press in new wheel studs. Front wheel hub press in either bolt turning or loosening by the torque of 108.5 lb•ft (147 N•m, 15 kg•m) shall not be premissible.

2. Mark new dust cover to match the removed dust cover. 3. Align mark on new dust cover with knuckle. 4. Install new dust cover with suitable tool.

5. Install new wheel bearing with suitable tool. 6. Install front wheel hub assembly with suitable tool.

• Use a new oil seal, and apply grease to seal. • Install oil seal so that it is flush with knuckle. 7. Install new oil seal with SST(0K993 331 016).

Something is blocking the way for the heat to reach the vents.
Reconnect the pipes

Use 2 bolts [ same size as screws ] 1.5'' - 2'' or so...thread into 2 screw holes...tighten both evenly untill drum comes off.

vehicletype=PASSENGER&mfrcode=KM&area=KMA&langcode=ENG&group=SHOP&modelid=GQ13&modelyr=2003&mmctype=en&mmcid=45&keyword=wheel+bearing&sitinfolist=31^3110^31100100^none^801^2^ENG^KM^GQ13^2003^all^0^none^none^none^shop^0$&cat1=SEDONA%28GQ%29+%26gt%3B+2003+%26gt%3B+Engine+%26gt%3B+Engine+Control+%26gt%3B+&firstnodedesc=Driveshaft+and+axle+%26gt%3B+Front+Axle+Assembly+%26gt%3B+Front+Hub+%2F+Axle+%26gt%3B+Repair+procedures+%26gt%3www.kiatechinfo.com/viewer/content.asp?vehicletype=PASSENGER&mfrcode=KM&area=KMA&langcode=ENG&group=SHOP&modelid=GQ13&modelyr=2003&mmctype=en&mmcid=45&keyword=wheel+bearing&sitinfolist=31^3110^31100100^none^801^7^ENG^KM^GQ13^2003^all^0^none^none^none^shop^0$&cat1=SEDONA%28GQ%29+%26gt%3B+2003+%26gt%3B+Engine+%26gt%3B+Engine+Control+%26gt%3B+&firstnodedesc=Driveshaft+and+axle+%26gt%3B+Front+Axle+Assembly+%26gt%3B+Front+Hub+%2F+Axle+%26gt%3B+Repair+procedures+%26gt%3B+ReassemblyB+Disassembly

Lower ball joints. Tighten the pinch bolts to 69-85 ft. lbs. (93-115 Nm). Outer tie rod ends. Tighten the nuts to 43-58 ft. lbs. (59-78 Nm). Sway bar links. Tighten nuts to 69-85 ft. lbs. (93-115 Nm). Hub retaining nuts. Tighten the hub nuts to 177-199 ft. lbs. (240-270 Nm). Front wheels. Tighten the lug nuts to 65-79 ft. lbs. (88-108 Nm).

Sometimes it just takes a little coersion. Try tapping on the back of it with a hammer. They can get a little stubborn at times. Good luck!

one check if your wheels are tight 95 ftlbs if mag wheels remove make sure no heavy corrosin arond hub and rim wheel will not seat properly and come loose. 2 check front end if belts are showing check ball joints and tie rides for wear vans are also known
for bad wheel bearings even if you cant hear it at 80km50mph give or take it may have ecssive play
check that front end .otherchecks ps pump and or loose p/s belt