Question about Seat Cars & Trucks

1 Answer

I have lost power to the 240v hook up circuit,the fridge still works on the hook up voltage but the 3 pin sockets have failed,i have 240v coming in to the the van as the fridge and hot water heater are ok,test at a junction box under the seat and the voltage is ok there,is the a internal fuse our mcb somewhere?

Posted by on

  • gbob59 Mar 19, 2015

    I believe it's more likely they are Circut breakers, which if they used conventional breakers, there should be a fairly big box I would think near the incoming supply. As well as the other supply. By three pin you don't mean 220vac do you? Standard socket for 110 and ground. So they could be smaller breakers. but I still would think the box to be near the incoming feed. This tool will work on any wire. It might help if you don't find an answer other wise. http://www.ebay.com/sch/i.html?_from=R40...

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Seat Master
  • 3,042 Answers

Sorry, I don't understand. As I understand it, everything works, except three pin socket (220 vac) socket for another appliance like a 220vac window air conditioner for example? Do you have a volt meter that says it failed? Usually. the middle pin is neutral.
so that voltage between it and either of the other two is 110vac.
The outer two should show 220vac.

Posted on Mar 19, 2015

Testimonial: "Sorry,its a Fleetwood Colchaster 1300/2 touring caravan think approx 1990,the electric hook up that plugs into the van for thr 240vac circuit is fine running into the caravan,the fridge is still working and so is the 240v heater for the hot water tank but there is only two three pin sockets in the caravan and there is no power going to them,think we have overloaded due to a electric blower and running a domestic kettle plus a tv ....wondered if there was a fuse it might have taken out on the 240v circuit inside the van for the sockets as i have no wiring diagram for the caravan,i have a fluke meter and i have 240 volt to a junction box under the seat but nothing at the sockets,just thought someone may have had this problem without me having to trace all the wiring from the sockets backwards ie a fuse i dont know about or a mcb which is unlikely due to the age of the caravan cheers Steve"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

97 crown vic air bag code 12,fuse 10 was blown replacd and it blows right away, 6 ohms to ground on non power side of fuse, where do i go from here?


In involved fuses #5 & #10 15 amp in main fuse panel

from Ford Service cd
http://www.fordcds.com/
Fault Code 12


Air Bag Deployment Circuit Drop in Battery Voltage


Circuit Description


Normal Operation

The diagnostic monitor measures the voltage at pin 13 of the diagnostic monitor connector. Voltage at pin 13 should be equal to battery voltage. If the voltage measured at pin 13 drops to less than 9 volts, the diagnostic monitor will flash out code 12.


Possible Causes

A drop in battery voltage at diagnostic monitor pin 13 can be caused by:

1.An open circuit that would prevent battery voltage from reaching diagnostic monitor pin 13.

NOTE:
If the instrument panel fuse and/or the power distribution fuse are blown, be sure to diagnose the system for possible causes 2 and 3 below.

2.A short to ground in Circuit 611 (W/O) or 612 (P/O) may result in a blown instrument panel fuse and/or power distribution fuse.

3.An internal short to ground within the safing sensor may result in a blown instrument panel fuse and/or power distribution fuse.

4.A problem in the charging system causing battery voltage to drop below 9 volts.

Jun 13, 2018 | Cars & Trucks

1 Answer

2002 f150 cruise inop shows code 3?


  • 3 flashes - deactivator switch is open or circuit defective.
    • Flash code 3 - deactivator switch circuit failure
    • Central junction box (CJB) fuse 13 (20A).
    • Circuitry.
    • Deactivator switch.
    • Speed control servo.
    • Go To Pinpoint Test H .
    PINPOINT TEST H: FLASH CODE 3 - DEACTIVATOR SWITCH CIRCUIT FAILURE
  • CONDITIONS DETAILS/RESULTS/ACTIONS H1 CHECK THE DEACTIVATOR SWITCH CIRCUITRY
    Speed Control Servo C122
    Measure the voltage between the speed control servo C122 pin 9, circuit 307 (BK/YE), harness side and the speed control servo C122 pin 10, circuit 57 (BK), harness side.
    • Is the voltage greater than 10 volts?
    Yes INSTALL a new speed control servo. REFER to Speed Control Servo in this section. REPEAT the self-test.

    No GO to H2 . H2 CHECK DEACTIVATOR SWITCH POWER
    Deactivator Switch C1025
    Measure the voltage between the deactivator switch C1025, circuit 10 (LG/RD), harness side and ground.
    • Is the voltage greater than 10 volts?
    Yes GO to H3 .

    No REPAIR the circuit. REPEAT the self-test. H3 CHECK CIRCUIT 307 (BK/YE) FOR AN OPEN Measure the resistance between the speed control servo C122 pin 9, circuit 307 (BK/YE), harness side and the deactivator switch C1025, circuit 307 (BK/YE), harness side.
    • Is the resistance less than 5 ohms?
    Yes INSTALL a new deactivator switch. REFER to Speed Control Deactivator Switch in this section. REPEAT the self-test.

    No REPAIR the circuit. REPEAT the self-test.

Nov 23, 2016 | 2002 Ford F-150

1 Answer

Why can I not get power to the small wire going to the starter on my 2004 taurus


You need to know how it works before you can diagnose it. There is a starter relay in the under hood fuse/relay box .. This relay is controlled by the PCM - engine computer . Does you car have a anti-theft system ? a red light on top of the dash or a SECURITY light on instrument cluster ? Is the red light flashing fast when trying to start the car . If you find an pull the relay out an look on the bottom you will or should see four numbers . 30 & 87 , 85 & 86. You can test from the socket where the relay plugs in . PIN'S 87 & 85 should have B+ voltage . PIN 30 takes voltage from PIN 87 to start the vehicle , PIN 86 is the control from the engine computer . The PCM gives a ground on this circuit to energize the relay closing the contacts inside ,completing the circuit between B+ voltage on PIN 87 to PIN 30 to start the car.

Feb 04, 2016 | 2004 Ford Taurus

1 Answer

I replaced iac sensor and it still shows bad.


Have to check powers and ground curcuit.

Idle Air Control Motor Circuit Malfunction Possible Causes Setting Conditions • Stepper motor connector is damaged (check pins for damage, and moisture) • Stepper motor Coil 1, 2, 3 or 4 circuit is open or shorted to ground • Stepper motor coil circuit(s) is shorted to voltage • Stepper motor has failed • PCM has failed Engine running; system voltage over 11.5v, and the PCM detected an incorrect voltage on one or more of the IAC motor circuits for 2.75 seconds with the motor enabled.

May 22, 2015 | 2002 Chrysler PT Cruiser

2 Answers

2006 Jeep Commander Tail light


The tail light circuit is separate from the brake and turn signal circuit. Either the bulb socket has gone bad or a wire has flaked out. Check for voltage at the socket on either pin base when you have your parking lights on. If voltage is present, it is either a worn socket failing to hold the bulb properly, or another bad bulb. If no voltage, determine which wire on the other side is tail light power, and run a new wire across to the side that isn't working and connect it to provide power.

Apr 09, 2014 | 2006 Jeep Commander

1 Answer

2000 Nissan Frontier Cigarette lighter not working while I use tire compresser using,


Tire compressor probably draws too much current for the socket. Are you sure it is a cigarette lighter socket? Some sockets are just to provide accessories 12v. Did a cigarette lighter come with this socket? True cigarette lighter sockets are generally fused at 25 or 30 Amps

Jan 08, 2018 | 2000 Nissan Frontier

1 Answer

I have C280 Mercedes Benz. The car starts, but the engine dies after about 20 minutes.


Symptoms look like thermal instability of either the cam shaft position sensor or the crankshaft position sensor. Sometimes these sensors can fail by outputting reduced voltage with temperature increase so they appear to works fine at start up but fail when the engine reaches running temperature. I think the the cam sensor is Hall effect and the cam sensor magnetic:

2 pin socket (magnetic - sine wave output). One pin is 'ground' the other is 'signal'. A voltmeter set to 2 volts AC (note) should measure a signal in the 0.2 to 2 volts range on the 'signal' pin.

3 pin socket (Hall effect, magneto - square wave form output). One pin is 'reference' (5volts), one pin is 'ground' and the third pin is 'signal'. A DC (note) voltage should be detectable in the 0.5 to 1.5 volt range from the 'signal' pin.
It is important that the voltage measurement take place at start up when the engine is cold and again, 20 minutes later, when the engine has fully warmed up to operating temperature. These devices do not often fail and are expensive if purchased from the the Mercedes dealership, shop around on-line or try a breakers yard.

Dec 07, 2010 | Mercedes-Benz C-Class Cars & Trucks

1 Answer

Q7 12V socket Inverter Wattage Question


no you need to know the wattage of the item you are trying to power. To find the wattage of the item you are trying to power is simple. Some will say directly others will give you the amps (ie. .5amps, 1.2 amps.) you take the amps and multiply it by the volts that it says. All this info is on the item you are trying to power with the inverter. The answer is what it will take to power that item. example .5amps x 240v = 120 w so in this instance you would need an inverter that would produce at least 120w so in this case the 150w inverter would work. Good Luck, have a grt day

Apr 01, 2010 | 2009 Audi Q7

3 Answers

P0340 code. I Changed cam sensor and checked wiring. what else could be wrong? Jeep cherokee, 6 cil


A code P0340 could mean one or more of the following has happened:

•a wire or connector in the circuit could be grounded/shorted/broken
•the camshaft position sensor may have failed
•the PCM may have failed
•there exists an open circuit
•the crankshaft position sensor may have failed

With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

•Visually inspect all the wiring and connectors in the circuit
•Check for continuity in the circuit wiring
•Check the operation (voltage) of the camshaft position sensor
•Replace the camshaft position sensor as required
•Check the crankshaft position circuit as well
•Replace circuit wiring and/or connectors as required
•Diagnose/replace the PCM as required

Feb 20, 2010 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Seat Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

84619 Answers

Adam Truesdale

Level 3 Expert

565 Answers

Are you a Seat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...