1999 Nissan altima replaced the oil pump was working for an hour and then stop working

francisco navarro

• 241 Answers
• Posted on May 15, 2008

SOURCE: Replacing a starter for a 1999 Altima

1. Disconnect battery ground cable.
2. Disconnect starter wiring from starter.
3. Remove starter retaining bolts and the starter.
4. Reverse procedure to install.

SOURCE: type of motor oil for a v4 2002 nissan altima

Should be in your owners manual... but generally 10W30 will do

SOURCE: nissan altima 2002 burning excesive oil what to

You have to identify where the oil is leaking. Check the spark plugs if it has oil, you may just need to replace the oil seal in the plugs. If you meant actual burning from the exhaust, you may want to check the head gasket and the piston rings if the oil seeps into the combustion chamber.

SOURCE: Nissan altima 94 engine dies out and stops randomly

the distibutor on these models are notorious for going out and then working again more than likely your problem

ZJ Limited

• 17989 Answers
• Posted on Apr 05, 2010

SOURCE: How do you remove a 1999 Nissan Altima starter?

Nissan Car Altima & Sentra 1999-06 StarterRemoval & Installation

1. Remove or disconnect the following:
   Negative battery cable Air duct Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle



Fig. Starter location and mounting detail-3.0L Maxima with a manual transaxle



Fig. Starter location and mounting detail-3.5L Maxima

1. Install or connect the following:
   Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short bolt to 22-30 ft. lbs. (30-41 Nm) Starter wiring Harness protector Air duct Negative battery cable

1. Remove or disconnect the following:
   Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Remove or disconnect the following:
   Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter

1. Install or connect the following:
   Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negaative battery cable
   

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter

1. Install or connect the following:
   Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable
   

1. Before servicing the vehicle, refer to the Precautions section.
   
2. Remove or disconnect the following:
   Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
   

1. Install or connect the following:
   Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable
   

1. Remove or disconnect the following:
   Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable
   

1. Remove or disconnect the following:
   Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
   

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1. Remove or disconnect the following:
   Negative battery cable Air cleaner cover and duct Harness bracket Wiring at the starter Starter

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1. Remove or disconnect the following:
   Negative battery cable Air cleaner case (upper) and air cleaner to electric throttle control actuator tube. Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle
   
   
   Fig. Starter location and mounting detail-3.5L engine