- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
1) Open trunk
2) Remove small round plastic access panel with a flat tip screw driver by prying open
3) Remove flat tip screw holding tail light assembly
4) Remove tail light assembly by pulling outward, careful not to break plastic guide/nub
5) Disconnect wiring connectors
6) Remove plastic housing access plate on back of tail light assembly by twisting/turning tabs until they click and then lift access plate from tail light assembly
7) When viewing the the bulbs, the turn signal bulb is the bottom left bulb
8) Install in reverse order, ensuring tail light seal seats properly during installation
You have to remove four screws near the center of the rear bumper that are visible when you open the trunk. Then remove the inside upholstery cover for each rear tail light and then remove the four brass bolts that hold each rear tail light assembly. Unhook the wiring harness so the tail light assembly can be removed and laid aside. Then remove the two screws on each side which were covered by the bottom of the tail lights. Next, remove some of the upholestry retaining pins close to the rear tailights so you can access the spcae behind them. You need to remove two brass nuts close to the outer aspect of where the tailights are located and two screws that are located several inches farther forward that are holding the more frontal aspect of the rear bumper on each side. Finally, remove two retaining screws at the bottom of the most forward aspect of the bumper (wheel well) and one at the top of the most forward aspect of the bumper and you should now be able to remove it! Hope this helps! John in Lexington
Access to the tail light cluster should be through panels in the rear corners of the vehicle. Remove the panel and you can remove the tail light cluster to replace the bulbs. This is the position on most sedans, unless, like on pick-ups, the tail light lenses have screws which allow the lenses to be removed to change the bulbs.
Access to the tail light cluster should be through panels in the rear corners of the vehicle. Remove the panel and you can remove the tail light cluster to replace the bulbs. This is the position on most sedans, unless, like on pick-ups, the tail light lenses have screws which allow the lenses to be removed to change the bulbs.
Lift the rear door, remove the rear tail light lense, replace the bulb and replace the tail light on the car.... once the screws have been removed, be sure all of them are removed,,, the lens/light cover may have to be pried off with a flat blade screw driver.... place a folded paper towel of something else to protect the paint.... before prying...... Check the owners manual for instructions.
Hi remove the tail light and remove the electrical connector then remove the top globe by twisting it anti clock wise then bend the contacts on the tail light up slightly and install the globe and tail light back
and Repair
Notes
TAIL LAMP REPLACEMENT
REMOVAL PROCEDURE
Open the rear compartment.
Remove wingnut and pull back the rear compartment trim panel from the tail lamp.
Remove the wingnuts from the tail lamp.
Remove the tail lamp from the rear body panel.
Disconnect the electrical connector from the tail lamp.
Remove the tail lamp socket, turning counterclockwise.
Remove the bulb from the tail lamp socket.
Remove the sidemarker lamp socket, turning counterclockwise.
Remove the bulb from the sidemarker lamp socket.
INSTALLATION PROCEDURE
Install the bulb to the tail lamp socket.
Install the bulb to the sidemarker lamp socket.
Install the sidemarker lamp socket, turning clockwise.
Install the tail lamp socket, turning clockwise.
Connect the electrical connector to the tail lamp.
Install the tail lamp to the rear body panel.
Install the wingnuts to the tail lamp.
Pull back the rear compartment trim panel to the tail lamp and install the wingnut.
Close the rear compartment.
×