1995 totoyota pick up 2.4 cylider head torque

Follow the link mazda b2500 torque sequence and settings cylinder head td bolts

Here's a link to your head bolt torque. Repair Guides Engine Mechanical Components Cylinder Head AutoZone com

cylinder head bolts:

step one: 22 Ft-lbs.
step two: tighten additional 90 degrees
step three: tighten additional 90 degrees

Go to a auto parts store (Pep Boys, Auto Zone, Advance, O'Reilly's, etc. ...they all have vehicle specific manuals for sale that will have a section on torque values.

Position the cylinder head on the cylinder block. Tighten the cylinder head bolts in 2 steps following the proper torque sequence. The first step is 37 ft. lbs. (50 Nm) and the second step is 68 ft. lbs. (92 Nm).

Hope this helps you.

Cylinder head bolt's torque.

Engine with Suffix B, Cylinder head will have 10 bolt's.
Ft.lbs (N.m)
Step 1 - 15 ( 20 )
Step 2 - Additional 90 deg.
Step 3 - Additional 90 deg.

Engine without Suffix B, Cylinder haed will have 14 bolt's.
Ft.lbs (N.m)
Outer Row 44 (60)
Center Row 66 (90)
Inner Row 66 (90)

Head bolts, 105-112 Foot pounds (Final torque)
Final torque must be reached in 3 equal steps. Recheck final torque in sequence.
Main Bearing Caps, Torque in sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs
Rod Bearing Caps, 45 Foot pounds (Final torque)

The connecting rod bearing cap nut on a four cylinder is 40 ft-lbs. The cylinder head bolts are torqued in four steps.1-45 ft-lbs 2-65 ft-lbs 3-65 ft-lbs 4 1/4 additional turn after reaching torque specification. On the V-6 & V-8 the connecting rod cap nuts at 45 ft-lbs and the headbolts are torqued in two steps 1-50 ft-lbs and 2-105 ft-lbs. Hope this will help you.

Are you aware that besides the torque, the cylider head bolts MUST be torqued in a specific sequence. The Ft/lbs of torque and the sequence are only available in the cars service manual or something similar like Chiltons repair manual. You can browse a copy of the Chiltons at a local library or bookstore and write down the ft/lbs and sequence. I've done it myself to save a few bucks

Hope this helps, from autozone site. Curt
Application:
Cylinder head bolt torque sequence

Note :
Torque sequence:
---------
front | 3 1 6 |
of | |
vehicle | 5 2 4 |
---------
Step 1: Lightly oil cylinder bolt threads & washers
Step 2: Torque to 22 Ft/Lbs
Step 3: Torque to 51 Ft/Lbs
Step 4: Loosen all bolts 180 degrees
Step 5: Loosen all bolts 180 degrees
Step 6: Torque bolts 1 & 2 to 25 Ft/Lbs
Step 7: Torque bolts 3, 4, 5, 6 to 11 Ft/Lbs
Step 8: Turn all bolts an additional 80 to 90 degrees
Step 9: Turn all bolts an additional 80 to 90 degrees
*** CAUTION ***
engine uses Torque To Yield head bolts (TTY) that
permanently stretch during the initial installation.
New head bolts must be used when cylinder head is
replaced or re-installed to obtain proper Torque.