Question about 2008 Infiniti FX35

1 Answer

How do i remove the inside rear door panel on a 2008 infiniti fx-35

Cannot open door from the inside but it will open from the outside

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Expert
  • 67 Answers

If it opens from the outside, check on the door itself near the latch assembly for a little black lever that moves back and forth...that is the child safety rear door lock and when engaged, wont allow the door to open from the inside...setting the lever to free position should allow door to open (pg 3-5 of owners manual)
https://owners.infinitiusa.com/content/manualsandguides/FX/2008/2008-Infiniti-FX4535.pdf

Posted on Mar 08, 2015

Testimonial: "wow was that simple. you sure save me from a big headache. i guess had i look in the owners manual i may have found the answer.the old saying if you can't figure it out then read the instructions. anyhow a great big thanks. greatly appreciated, Harold"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 XC90/rear doors won't open from inside. Is there a switch? Or is there a problem?


Yes there is open doors a small switch should be below the door latch.if you can not find look in the owner manual

Dec 29, 2012 | 2008 Volvo XC90

2 Answers

How do i change rear turn signal bulb


I just watched the service station replace the rear turn signal bulb of our 2008 Enclave in about 5 minutes for $30! He opened the tail gate door, there were two small squares in the black lighting panel trim that he popped open. Inside each was a screw that he removed. This enabled him to remove the whole lighting panel. He then twisted the bad bulb and removed it and replaced with a new one. He checked that it was working then popped everything back into place added the screws and closed the squares back up. DONE!

Sep 10, 2010 | 2008 Buick Enclave

1 Answer

Back door will not open at all 1994 infiniti j30 how can i get it open tried to take off panel not enough room any solutions need help


Did you check to see if the child safety lock may have been activated? If so the door will only open from the outside.Try removing the power door lock switch/arm rest assembly to see if the door lock switch can be jumped out in the event the door lock switch is burnt out.
Does the Infiniti have an exterior key lock cylinder on the rear door? If so try to get a key to open the lock, it may be very difficult to remove the door panel when the door is sealed closed, but if you can that may be your only salvation short of attemting anslim jim door opening tool down the side of the door glass in ho[pes to trip the door linkage lock thus opening the door.

Jun 05, 2010 | 1997 Infiniti.5 J30

1 Answer

Need a diagram for installing a drivers side electric power mirror on a 1995 mercury villager van


here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal
  1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
  1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).




  1. Remove the wire clip.
  1. Disconnect the power outside rear view mirror electrical connector.




  1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.




Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal
  1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
  1. Remove the two outside rear view mirror inside mounting hole cover screws.


    Remove the outside rear view mirror mounting hole cover.
Installation
To install, reverse the removal procedure. Mirror Control
Removal
  1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).


May 13, 2010 | 1995 Mercury Villager

1 Answer

2008 nissan altima, can't open drivers door from outside, how to remove outside door handle


you need to remove the inside door panel to gain access to the guts of the door handle. its a pretty extensive repair for a novice.

Jan 09, 2010 | 2002 Nissan Altima

1 Answer

Problem The rear hatch door will not unlock.


First, on the rear hatch, there is an actuator. On FX, when you close the trunk, it kind of **** the hatch closed all the way. When you press lock on the remote, this same actuator locks it as well.
Now,
1) when you unlock the car from the inside, go back there and press the button to open the hatch door manually, do you here any noises?
2) Close all doors, go back close to the hatch button and using the remote , lock the car and then unlock the car. you should hear a sound from the actuator locking and unlocking the lock on the rear hatch!

If you don't hear this, your actuator is inop.
Next step would be to check the fuses inside the car, on the left bottom driver side, and outside on the battery compartment.
It might be just a fuse.
If all fuses check ok, your actuator is most likely gone! Not ea expensive fix, just time consuming!

NOW, if you can hear the noises, then something is either broken inside the actuator or one of the cables is loose!
Hope that helps.
Also, what year and miles on your fx?

Oct 20, 2009 | 2004 Infiniti FX35

1 Answer

Cannot find the usb port on my 2008 infiniti fx 35. would anyone know?


for the most part they are under the hood are under the dash on the driver sidetry these websites www.autozone.com and www.alldatadiy.com

Jul 30, 2009 | 2008 Infiniti FX35

1 Answer

Rear door on driver side won't open,have taken the panel off the inside of car,seems like the lock won,t travelas far as it does on the other door.is there any way to open this door,thanks[1997 lincoln...


Rear
Removal
  1. Using a small screwdriver, remove the screw cover from the armrest of rear door trim panel (27406).
  1. Remove the two retaining screws.
  1. Using Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry rear door trim panel from door inner panel.
  1. Disconnect electrical connectors.
Installation
  1. Position rear door trim panel on door inner panel, aligning two locators on rear door trim panel. Reverse Removal procedure.
------------------------------------------------------------------------------------ Rear
Removal
  1. Remove door trim panel and watershield. Refer to Section 01-05 .
  1. Check all connections of remote control links and cables. Service as necessary.
  1. Remove remote control assembly.
  1. Remove door latch remote control assembly from latch assembly.
  1. Drill out rivet at bellcrank and link (264B14).
  1. Remove three screws attaching latch assembly to door.
  1. Drill out rivet that attaches actuator motor to door.
  1. Remove latch assembly with actuator motor and door latch control rod lever link assembly.
Installation
  1. Install new bushings and clip onto latch assembly.
  1. Install latch with links and power lock actuator into door cavity.
  1. Position latch assembly to door, aligning screw holes in latch and door. Install three screws. Tighten to 10-13 Nm (89-115 lb-in).
  1. Attach door latch actuator motor to door with a new rivet.
  1. Install bellcrank and link to door using a new rivet.
  1. Install inside door handle and remote control assembly to door.
  1. Open and close door to check latch assembly operation.
  1. Install watershield and door trim panel. Refer to Section 01-05 .
ee8a11f.gif
Item Part Number Description 1 221A00 Door Handle to Door Latch Actuating Cable 2 26446 Rear Door Control Rod Retainer 3 377901 Plug Button 4 26412 Rear Door Latch 5 W623451-S2 Push Nut 6 224A32 Counter Balance 7 22450 Door Outside Handle Tension Spring 8 W701210-S309 Screw 9 224A20 Outside Door Handle Anti Rattle Pivot (2 Req'd) 10 22404 Door Handle 11 224A24 Front Door Outside Handle Spacer (2 Req'd) 12 264A64 Rear Door Actuating Rod 13 22408 Outside Door Handle Anti-Rattle Bumper 14 22428 Outside Door Handle Large Pad 15 N621906-S2 Nut (2 Req'd) 16 N807329 Screw (3 Req'd) 17 26595 Rear Door Electric Latch Actuator (RH) 18 W701566-S47 Rivet 19 431C04-A Rear Door Latch Striker Assembly 20 — Door Lock Striker Plate (Part of Door Shell Assy) 21 W525172-S Rivet (2 Req'd) 22 264B14 Bellcrank and Link (RH) 23 264A50 Bushing 24 N802034-SG Rivet 25 26420 Rear Door Latch Control Rod Link 26 W525172-S Rivet (2 Req'd) 27 21818 RR Door Latch (Inside) 28 A26460 RR Door Latch Push Button Rod 29 21982 Door Latch Rear Striker Assembly 30 N808377-S101 Screw (2 Req'd) 31 250A04 Rear Door Catch 32 N801010-S100 Truss Head Bolt (2 Req'd) 33 N804234-S2 Screw 34 266A74 Rear Door Latch Actuator Retainer 35 24630 Rear Door 36 26552 Rear Door Latch Control Escutcheon A — Tighten to 21-29 Nm (16-21 Lb-Ft) B — Tighten to 10-13 Nm (89-115 Lb-In) C — Tighten to 7-8 Nm (62-70 Lb-In) D — Tighten to 26-34 Nm (20-25 Lb-Ft) E — Tighten to 3-4 Nm (27-35 Lb-In)

Mar 24, 2009 | 1997 Lincoln Continental

1 Answer

Rear passenger doors locked but won't open


if you cant open it from inside or out side it has to be latch assy. that locks on the body . the part that is bad is inside the door there should be 3 boltz phillips screwdriver that you can see from outside . you wil have to remove door panel then there is connecting rods the part is about 50.00 used wreckcars@aol.com. if needed

Dec 24, 2008 | 2008 Hummer H3

Not finding what you are looking for?
2008 Infiniti FX35 Logo

458 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

Marvin
Marvin

Level 3 Expert

85111 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...