Question about 2007 Subaru B9 Tribeca

Open Question

I have a 2007 B-9 subaru. The remote locks, sound system, interior lights and part of the acc. control lights aren,t working. The interior fuses are all good. Which of the fuses in the engine compartment would cause this and how do i test them?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 15 Answers

SOURCE: abs light on, cruise control and engine light 2007 subaru outback

55 EGR Temperature Sensor or Circuit

ABS light is nothing to do with code 55 separate fault circuits.

Under dash there are two wires with mini spades at the end, connect one of them to the single black multiplug in position 2. Thats RHS plug inlet when you hold plug with tab lock on top.
ABS sensor should then flash up error coded. Ignore code 11 thats a initial flash to let you nknow the difference between a fast and slow flash.

Let me know what code flashes up and I will tell you the symptom,

Dan

Posted on Jan 08, 2009

Ad
  • 270 Answers

SOURCE: For 2001 Forrester Subaru - Front Windshield Washer fuse

If it makes noise, it's not the fuse. Most likely the discharge nozzles are stopped up. Try blowing compressed air into them from the outside.

Posted on Dec 19, 2009

planet-x
  • 232 Answers

SOURCE: My Subaru Forester engine light and cruise control

could be transmission fault, connect the 2 loose black plugs together under the drivers side dash, turn on ignition, no start, the ecl will flash the code, slow flashes are 10's and fast ones are 1's. codes can be got from bba-reman.com

Posted on Jan 13, 2010

CarMech97
  • 427 Answers

SOURCE: I have a 2002 subaru

Did you check the fuses with a test light?

Posted on Aug 27, 2011

pied
  • 195 Answers

SOURCE: Rear brake light aren't working subaru legacy 2004

Check the bulbs, if they are OK you may have a faulty brake light switch.

Posted on Dec 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dome light, radio, clock, interior lights and remote door locks not working


Check your fuses. I think all the circuits you mentioned are on the same fuse.

May 29, 2015 | 2007 Subaru Outback

1 Answer

2001 maxima alarm not working but panic works


ck for a fuse in the under the hood fuse box that says bsm may be blown.
Also try this.....
To reset the security system remove the negative battery cable for 30 minutes, then reconnect the cable. Next, lock and unlock the doors using the remote. This will reset the alarm system and the engine will start and fobs reset.

Here are some factory notes....FYI

Anti-Theft Systems

PROGRAMMING

NOTE: If a new Smart Entrance Control Module (SECU) is installed, a new identity code must be entered and all remote controllers must be programmed. If identity code cannot be entered, repair multi-remote system. See appropriate MULTI-REMOTE CONTROL SYSTEMS article.

PROGRAMMING > PROGRAMING NEW ID CODE

NOTE: This procedure will erase all previous identity codes and render all previously programmed remote controllers inoperative (until reprogrammed). All remote controllers to be used with system must be programmed at the same time. A maximum of 4 remote controllers can be programmed. Any attempt to program more than 4 controllers will be ignored. If same identity code is entered more than once, entry is ignored even though hazard warning lights will still flash twice.
1. Close and lock all doors. Erase original identity code(s) by inserting and completely removing key from ignition switch more than 6 times within 10 seconds. Hazard warning lights should flash twice. Turn ignition switch to ACC position.
2. Push any button on new remote controller once. Hazard warning lights should flash twice, indicating identity code has been entered. If identity code cannot be entered, repair multi-remote system. See appropriate MULTI-REMOTE CONTROL SYSTEMS article.
3. For each additional remote controller to be programmed, manually release door lock and lock again by using door panel switch and repeat step 2. If no additional remote controllers are to be used, exit programming mode by unlocking and opening driver's door.

Please let me know if you need anything else to get the problem fixed. Happy mew Year!

Jan 03, 2018 | 2001 Nissan Maxima

3 Answers

Subaru Tribeca 2006; the radio stopped working the interiors lights don't turn on, the lights for the temperature gages don't turn on and the alarm system does not work. Also every time I turn on the car...


had the same problem. no radio, navigation interior lights etc. replaced 20 amp fuse labeled "back up" in the engine compartment fuse box and all checks good.

Nov 08, 2010 | 2006 Subaru B9 Tribeca

5 Answers

Mk4 Golf. Remote locking, windows and interior lights not working


Maybe fuse number 6 is blown (check lefthand side of steerning wheel where all teh fuses are located - you must open the door)

Jan 10, 2010 | 2003 Volkswagen Golf

2 Answers

2000 Concorde - power locks, interior lights, radio not working


There is most likely a fault in the system and it will have to be reapired by certified tech

Jun 25, 2009 | 2000 Chrysler Concorde

1 Answer

1997 venture keyless remote programming


SYSTEM OPERATION

System warning lamp located on top of the instrument panel
Press UNLOCK button once , turns on interior lamps and deactivates alarm (if fitted)
Press UNLOCK button twice w/in 5 seconds unlocks all doors, turns on interior lamp and deactivates alarm (if fitted)
To activate alarm system (if fitted):
Switch ignition OFF
Open driver's door
Press Lock button on remote
Close Driver door
warning lamp will flash when system is activated
Press remote power sliding door button will open sliding door (if fitted) only if unlocked first
Pressing remote panic button:
*Sounds horn intermittently
*Flashes exterior lamps
*Turns on interior lamps
**Pressing panic for the second time OR switching ignition ON deactivates alarm.


PROGRAMMING
Remobe key from ignition switch
Remove the "BCM PRGRM" fuse, from the fuse box
Close all doors
Turn ignition switch to the ACC position
With in 1 SECOND , turn the ignition switch to OFF then back to 'ACC'
(really, with in one second)
Open and close the driver's door. A chime will sound, indicating programming mode activated
Press and HOLD LOCK and UNLOCK SIMULTANEOUSLY untill a chime sounds 2 times ( about 15 seconds)
Repeat this exact procedure for all remotes to be programmed
Remove key from ignition
Refit 'BCM PRGRM' fuse.

4 REMOTES MAXIMUM CAN BE PROGRAMMED

Aug 24, 2008 | 2000 Chevrolet Venture

1 Answer

1995 B4 fuse diagram in japanese writing, need to replace door lock fuse.


Yes the interior lights are always hot circuits, the radio keep alive memory most likely runs off this same circuit. The fuse should be marked courtesy lights.

Aug 15, 2008 | 1997 Subaru Legacy

Not finding what you are looking for?
2007 Subaru B9 Tribeca Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

Marvin
Marvin

Level 3 Expert

84625 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...