Question about 2008 Cadillac Dts

Open Question

Replace front turn signal bulb on 2008 Cadillac d t s

Replacing front turn signal bulb

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: Replacing front turn signal bulb on 2006 Cadillac SRX

wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.

Posted on Jan 25, 2009

Ad
greezy_je208
  • 237 Answers

SOURCE: left front turn signal bulb is out on my 2007

easily mabe. look down from under the hood, if not try try from underneath.

Posted on Dec 18, 2009

  • 1 Answer

SOURCE: 2004 CTS Cadillac front passenger turn signal bulb is out.

Actually no you don't. Crank your steering wheel all the way to the right so yo have the maxumum clearance for your hands and arms in the front of the wheel well. Remove the plastic clips that hold the wheel well splash guard and pull it back enough to allow access to the interior of your bumper.
Replace bulbs as needed.
Yes, a jack is nice and makes it a touch easier to access, but I did this in an AutoZone parking lot during a cross country road trip.
5 mins tops to complete.

Posted on Mar 14, 2010

duane_wong
  • 6826 Answers

SOURCE: How do I replace the front turn signal bulb?

that's a tough one to do. Requires unscrewing bolts underneath the car to remove the entire lense assembly. Best left to a professional or a lot of time (1 or 2 hours) to undo everything and put it back.

Posted on Jul 02, 2010

  • 1 Answer

SOURCE: Need to replace front turn signal bulb on a 2004

need to remove front wheel and panel from the inside.

almost the entire wheel cover need to come off

Posted on Aug 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace right front turn signal bulb on 2008 cadillac dts


My automotive database says you have to remove headlamp assembly to replace bulb. To remove headlamp assembly, you need to remove front bumper fascia.
Why in the world should you have to remove front of vehicle just to change a bulb, I don't know? My database is the only info I have to go by. I doubt I can walk you through it, step by step, I can't see anything from here.

Mar 01, 2016 | 2008 Cadillac Dts

Tip

Change the front turn signal bulb on Cadillac SRX


I have found a short cut for changing the front turn signal bulb
  1. Remove the inner fender well cover and then you can remove the light assemble from underneth and replace the bulb.
  2. The cover is attached with a bunch of push on body clips, pry the button up with a screwdriver and pull out fastner.
  3. Then there are two screws holding the light assembly on the bottom and inner side, it clips into the bumper on the outter side. From there it's pretty simple.
  4. FYI the GE replacement cross reference is wrong it's a Sylvania 3757A LL bulb.

on Dec 02, 2009 | Cadillac SRX Cars & Trucks

1 Answer

How to change front turn signal bulb on 2008 SRX Cadillac


Nope don't need to drop the whole light assembly. I just took the wheel and inner cover off, then the 6 torx screws that hold the light hosing together , replaced the turn signal bulb and good to go!!

Mar 04, 2013 | 2004 Cadillac SRX

1 Answer

How do i replace the fuse for the front turn signal on 2006 cadillac srx


The socket is defective?? Probe the socket with a volt meter to see if voltage is turning on and off to trigger the bulb to flash.

Jul 09, 2012 | 2006 Cadillac SRX

1 Answer

Change turn signal bulb 2008 srx


Front turn signal bulb replacement 2008 SRX . Jack up car & block . Remove front wheel & front half of the wheel house assemble. There are about 7 plastic pull rivets that have to be removed . Pull out the wheel house . Remove turn signal & driving light cover held on by 6 # T10 torx screws . Twist out socket & replace bulb # 3757NAK . Should take about 45 min.

Mar 26, 2012 | 2006 Cadillac SRX

2 Answers

2004 CTS Cadillac front passenger turn signal bulb is out.


Actually no you don't. Crank your steering wheel all the way to the right so yo have the maxumum clearance for your hands and arms in the front of the wheel well. Remove the plastic clips that hold the wheel well splash guard and pull it back enough to allow access to the interior of your bumper.
Replace bulbs as needed.
Yes, a jack is nice and makes it a touch easier to access, but I did this in an AutoZone parking lot during a cross country road trip.
5 mins tops to complete.

Feb 19, 2010 | 2004 Cadillac CTS

1 Answer

How do I replace the front turn signal bulb?


that's a tough one to do. Requires unscrewing bolts underneath the car to remove the entire lense assembly. Best left to a professional or a lot of time (1 or 2 hours) to undo everything and put it back.

Jun 09, 2009 | 1990 Cadillac Deville

1 Answer

2008 Camry Front Turn signal Bulb


Front Open The Hood And View Back Of Headlight Turn And Then Pull Light.
Rear Open Trunk And Remove Carpet From Behind Light Now You Can View The Bulb Housing Turn And Pull.

Nov 16, 2008 | 2008 Toyota Camry

2 Answers

Replacing front turn signal bulb on 2006 Cadillac SRX


You must take the front wheel off, then remove the inner front fender panels (2), they are fastened with plastic pushbuttons. this exposses the light housings for the turn and fog lambs. This takes about an hour, but saves you alot of money.

Nov 12, 2008 | 2006 Cadillac SRX

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

258 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...