My turn signals, windshield wipers and rear window defroster stopped working all at the same time. The fuse and multi-function switch are both fine.

Rear Wiper/Washer System Components
The rear wiper/washer system consists of the following components:
• Rear wiper/washer switch
• Window wiper module-rear
• Window washer pump-rear
• RR WIPER 15A fuse
• RR WPRB 25A fuse
Rear Wiper/Washer System Operation
The rear wiper module controls rear wiper motor operation. Battery voltage supplied to the module is used to operate the wiper motor in all modes and to return the rear wiper arm to the park position after the ignition is turned off. Accessory voltage supplied to the rear wiper/washer switch is used to supply the rear window wiper and washer switch signal circuits. In wiper switch positions 1 and 2 the wiper switch signal circuit voltage level to the wiper motor module determines the wiper motor delay interval. The rear window washer pump supply voltage circuit is used to provide the operating voltage for the rear washer pump for as long as the rear washer switch is pressed. The rear window washer switch signal circuit is used as a wash signal to the rear wiper motor module to operate the wipers during the rear wash operation.


Did you replace the rear wiper module ?

The washer fuse should have power (battery voltage) while the ignition switch is in the RUN position. Verify both sides of the fuse have power. If the rear wash functions them it's not the fuse.

The switch signals the Body Control Module (BCM). The BCM energizes the front washer relay.

Input to BCM from switch is BCM connector C1,24 PK. Output from BCM to relay is connector C4 15 OG.

You need to verify continuity from the the switch to the BCM and from the BCM to the relay.

Comment below for further assistance.

Did you check fuse's & relays ?
Rear Window Wiper Operation
The rear wiper motor is controlled by the SJB. The SJB supplies power to the rear wiper motor from the integrated rear wiper relay. The SJB will activate the relay when all of the following conditions are met:

• Ignition switch is in the ON position
• Liftgate glass and liftgate are closed
• Multi-function switch is in the ON or intermittent position

The SJB also supplies voltage to the rear wiper motor from SJB fuse 21 (15A) when the ignition switch is in the ON position. This power feed is used to continue the wipe cycle when the multi-function switch is turned to the OFF position. The SJB receives inputs from the multi-function switch that applies ground to the low speed wipe input or applies ground to the intermittent wipe input. When either of these circuits are grounded, the SJB activates the integrated rear wiper relay and power is supplied to the rear wiper motor to move the rear wiper motor from the park position. An internal switch in the rear wiper motor then moves to the run position which connects the accessory relay power to the rear wiper motor. When the rear wiper motor returns to the park position, the internal switch in the rear wiper motor moves back to the park position. If the multi-function switch is in the ON position, the rear wiper relay is still activated, power is supplied to the rear wiper motor, and the wipe cycle starts again. If the multi-function switch is in the intermittent position, the rear wiper relay does not activate until the predetermined dwell time has elapsed, at which time the SJB activates the rear wiper relay and the wipe cycle starts again. The SJB is the smart junction box .(computer )

Rear Washer System
The SJB supplies power to the rear washer pump from fuse 21 (15A) when the ignition switch is in the ON or ACC position. The rear washer pump receives ground from the multi-function switch when the wash function is turned ON. The multi-function switch also signals the SJB when the rear wash is activated and the SJB then activates the rear wiper.

Do the wipers work ? Fuse for wipers is same as washer pump .
Principles of Operation
The wiper motors receive inputs from the following:

• Multi-function switch
• Powertrain control module (PCM)
• Ignition switch
• Smart junction box (SJB)

The following components are integrated in the wiper motors:

• Windshield wiper motor module
• High/low speed relay
• Run/park relay
• Washer pump relay
• Park sense (Hall-effect sensor)

Washer System
The windshield washer and the rear window washer are activated by the internal wiper motor modules when it receives a ground from the multi-function switch between the washer inputs. Depending on the correct ground, the internal wiper motor modules activate either the windshield washer or rear window washer relays (internal) by grounding the respective relay coil. When either module is activated, it connects voltage to the washer pump while the deactivated module provides ground to the washer pump. In this manner, voltage polarity is reversible to achieve directional change of the washer pump and washer fluid.

• The washer pump is inoperative

• Circuitry
• Washer pump
• Multi-function switch
• Windshield wiper motor
• Rear window wiper motor

• Go To Pinpoint Test I .

Does your expedition have programmable/recall memory option for seats an mirrors ?
Driver Seat Module
The power driver seat and power exterior mirrors are controlled by the driver seat module (DSM) only when the vehicle is equipped with the programmable/recall memory option.
On the Expedition Limited, the power fold exterior mirror option is controlled by the DSM. Before running a self-test or retrieving codes, the power fold switch must be inactive for at least 30 seconds.
This is a complex vehicle , electronics , control modules an serial data communication networks. You mite be better off taking it to the dealer or some other repair shop . There could be DTC'S - diagnostic trouble codes stored in the SJB - body control module !
B1667 Mirror Driver Up/Down Motor Stalled Go To Pinpoint Test D . B1668 Mirror Driver Right/Left Motor Stalled Go To Pinpoint Test D . B1669 Mirror Passenger Up/Down Motor Stalled Go To Pinpoint Test D . B1670 Mirror Passenger Right/Left Motor Stalled Go To Pinpoint Test D . B1735 Mirror Driver Vertical Switch Circuit Short to Battery Go To Pinpoint Test D . B1739 Mirror Driver Horizontal Switch Circuit Short to Battery Go To Pinpoint Test D . B1743 Mirror Passenger Vertical Switch Circuit Short to Battery Go To Pinpoint Test D . B1747 Mirror Passenger Horizontal Switch Circuit Short to Battery Go To Pinpoint Test D . B2312 Mirror Horizontal Feedback Potentiometer Circuit Failure Go To Pinpoint Test D . B2314 Mirror Passenger Horizontal Feedback Potentiometer Circuit Short to Battery Go To Pinpoint Test D . B2316 Mirror Passenger Vertical Feedback Potentiometer Circuit Failure Go To Pinpoint Test D . B2318 Mirror Passenger Vertical Feedback Potentiometer Circuit Short to Battery Go To Pinpoint Test D . B2320 Mirror Driver Horizontal Feedback Potentiometer Circuit Failure Go To Pinpoint Test D . B2322 Mirror Driver Horizontal Feedback Potentiometer Circuit Short to Battery Go To Pinpoint Test D . Normal Operation During normal operation, when the front wiper wash is selected, the windshield wiper motor provides power to the washer pump through circuit CRW14 (BU/WH) and ground is provided to the washer pump through circuit CRW12 (GY/OG) and the rear wiper motor. If rear wiper wash is selected, the rear wiper motor provides power to the washer pump through circuit CRW12 (GY/OG) and ground is provided to the washer pump through circuit CRW14 (BU/WH) and the windshield wiper motor.

Possible Causes
• Multi-function switch
• Open in circuit CRW14 (BU/WH), CRW12 (GY/OG), CRW07 (GY/BN), CRW20 (GY/YE), SBB49 (RD) or GD149 (BK/GY)
• Short to ground in circuit CRW14 (BU/WH), CRW12 (GY/OG), CRW07 (GY/BN) or CRW20 (GY/YE)
• Washer pump
• Windshield wiper motor
• Rear wiper motor
  This is

The only thing they have in common is the ignition switch.

The wiper control module is probably at fault ,without test that is just a guess . The wiper/washer switch is a input to the wiper control module. Do you know anything about automotive electronics an electrical systems ?

• The Wipers are Inoperative

• Fuse.
• Wiper motor.
• Multi-function switch.
• Circuitry.
• Wiper control module.

• GO to Pinpoint Test B .

Voltage drop testing the power an ground circuits for the wiper control module would be a good place to start . Do you know how to test electrical circuits with a volt meter ?
PINPOINT TEST B: THE WIPERS ARE INOPERATIVE CONDITIONS DETAILS/RESULTS/ACTIONS B1 CHECK FUSE JUNCTION PANEL FUSE 16 (30A)
Fuse 16 (30A)

• Is the fuse OK?

Yes GO to B2 .

No REPLACE the fuse. TEST the system for normal operation. If the fuse fails again, CHECK for a short to ground. REPAIR as necessary. B2 CHECK FOR VOLTAGE TO THE WIPER CONTROL MODULE - CIRCUIT 65 (DG)
Wiper Control Module C294
Measure the voltage between wiper control module C294-2, circuit 65 (DG), and ground; and between wiper control module C294-11, circuit 65 (DG), and ground.

• Is the voltage greater than 10 volts?

Yes GO to B3 .

No REPAIR circuit 65 (DG). TEST the system for normal operation. B3 CHECK CIRCUIT 57 (BK) FOR OPEN Measure the resistance between wiper control module C294-3, circuit 57 (BK), and ground; and between wiper control module C294-5, circuit 57 (BK), and ground.

• Are the resistances less than 5 ohms?

Yes GO to B4 .

No REPAIR circuit 57 (BK). TEST the system for normal operation. B4 CHECK THE MULTI-FUNCTION SWITCH
Multi-Function Switch
Check the multi-function switch; refer to Section 211-05 .

• Is the multi-function switch OK?

Yes GO to B5 .

No REPLACE the multi-function switch; REFER to Section 211-05 . TEST the system for normal operation. B5 CHECK CIRCUIT 993 (BR/W) FOR OPEN Measure the resistance between multi-function switch C269-4, circuit 993 (BR/W), and wiper control module C294-7, circuit 993 (BR/W).

• Is the resistance less than 5 ohms?

Yes GO to B6 .

No REPAIR circuit 993 (BR/W). TEST the system for normal operation. B6 CHECK CIRCUIT 589 (O) FOR OPEN Measure the resistance between multi-function switch C269-1, circuit 589 (O), and wiper control module C294-1, circuit 589 (O).

• Is the resistance less than 5 ohms?

Yes GO to B7 .

No REPAIR circuit 589 (O). TEST the system for normal operation. B7 CHECK THE WIPER CONTROL MODULE OUTPUT FOR VOLTAGE
Wiper Control Module C294

Wiper Motor C152
Turn the multi-function switch to the HI position. Measure the voltage between wiper motor C152-4, circuit 57 (BK), and wiper motor C152-3, circuit 56 (DB/O).

• Is the voltage greater than 10 volts?

Yes REPLACE the wiper motor; REFER to Motor-Windshield Wiper . TEST the system for normal operation.

No GO to B8 . B8 CHECK CIRCUIT 57 (BK) FOR OPEN Measure the resistance between wiper motor C152-4, circuit 57 (BK), and ground.

• Is the resistance less than 5 ohms?

Yes REPLACE the wiper control module; REFER to Module-Windshield Wiper . TEST the system for normal operation.

No REPAIR circuit 57 (BK). TEST the system for normal operation.

Multi function control switch has to be replaced.

Try replacing the wiper relay first then if problem still exist replace multi-function switch

hello,good day,hoping your fuse is in order,may check your fuse in engine room,if ok,better to send your car to your dealer,because signal light and wiper system is connected to a control module,to avoid parts replacement not deffective,ty

sounds like you have a bad multi function switch ( the wiper switch that is also a turn signal switch)